sprinklers_pi

Sprinklers Pi is a sophisticated Irrigation control system for the Raspberry Pi. The system contains a built in mobile web page server that can be used to configure and monitor the system status from anywhere. It can also be cross compiled on an AVR/Arduino platform with appropriate networking and storage hardware.

Major Features

Fully contained system with control logic and web serving.
Same code can be compiled to run on the Atmel/AVR/Arduino platform.
Web based control (including mobile Android iOS)
Automatic adjustment of intervals based on weather conditions. (weather underground API)
Weather conditions can be pulled from individual personal weather stations or from general weather data based on zipcode.
Manual Control
Scheduled Control
Quick Schedule
Named Zones
Full Graphing feature of historic logs
Ability to run with OpenSprinkler module, direct relay outputs or an external script.
Supports master valve/pump output
Supports expansion zone board (up to 15 zones)
Very simple installation
Seasonal adjustment.

Weather Setup

By default, we now ship with no weather provider enabled, and therefore no adjustment performed. Follow the directions below to enable a weather provider. If you change weather providers be sure to run "make clean" before rebuilding.

OpenWeather / OpenWeatherMap

This is the current recommended free provider, however, it is currently unsupported on Arduino/AVR Platforms due to a dependence on curl and a JSON library that is currently untested on Arduino. It works on Linux devices including raspberry pi.

OpenWeatherMap appears to now require a CC on file for new accounts in order to work properly.

As long as you use less than 1000 calls / day it is still free. Sprinklers_pi will only make calls before starting a schedule and when you use the Weather Provider Diagnostics page so you should be no where near this limit.

Uncomment #define WEATHER_OPENWEATHER in config.h before building.
Build and start the server.
Navigate to the Settings Page.
Fill in API Secret with your api key from this page: https://home.openweathermap.org/api_keys
Fill in Location in the format: lattidue,longitude (eg. "40.749748,-73.991618")
Click "OK" at the top to save.
Navigate to the Advanced -> Weather Provider Diagnostics page to test everything is working.

DarkSky Weather

WARNING: Darksky has been aquired by Apple and is shutting down their free API at the end of 2021.

Uncomment #define WEATHER_DARKSKY in config.h before building.

DarkSky is currently unsupported on Arduino/AVR Platforms due to a dependence on curl and a JSON library that is currently untested on Arduino.

Once you have built and started the server fill out the API Secret Key in the Settings page (API Id is unused). Your Secret can be found here: https://darksky.net/dev (account required, free). Location must be (without the quotes):

GPS Latitude,Longitude (eg. "40.749748,-73.991618")

Aeris Weather

Uncomment #define WEATHER_AERIS in config.h before building.

Once you have built and started the server fill out the API Id, API Secret, and Location in the Settings page. Your API Id and Secret can be found here: https://www.aerisweather.com/account/apps (account required, free, must be renewed every 2 months). Location can be any of the following:

GPS Latitude,Longitude (eg. "40.749748,-73.991618")
City, State (eg. "New York, NY")
City, Country (eg. "London, United Kingdom")
ZIP Code (eg. 10001)

Testing Weather Data

You can click on Advanced -> Weather Provider Diagnostics to verify your setup is working.

See the wiki for more information: https://github.com/rszimm/sprinklers_pi/wiki/Weather-adjustments

Building

make
sudo make install

NOTE: If you are running an older version of g++ compiler you may see the error unrecognized command line option '-std=c++11'. You should either update to g++ version 4.8+, or if you are not using DarkSky as a weather provider, you can remove -std=c++11 at the end of line 8 in the Makefile. You can see what version of g++ you have by running g++ --version.

Running

sudo /etc/init.d/sprinklers_pi start

See the wiki for more information: https://github.com/rszimm/sprinklers_pi/wiki

Live Demo

A live demo site is available here: http://kilby.kewlshells.com:8080/ Please keep it clean.

License

rszimm/sprinklers_pi

About

Resources

License

Stars

Watchers

Forks

Releases 21

Packages 0

Contributors 8

Languages

Packages