Ender 3v2 with Sprite Extruder Pro and BL touch - Setting

[b771x]

Hello,
I use firmware Ender3V2-422-BLTUBL-T13-MPC-20230312.bin. I have problem to make correct physical and probe setting. Who has the same HW configuration: Please can You help me:

1. What Mriscoc version of firmware to use
2. What physical and probe exact values to setup ?
   Thanks for the answer

[JohnDelisle]

I'm running a self-compiled Ender3V2-422-BLTUBL-T13-LA-MPC. I'm working through configuring it, but used to run your firmware and can share most of the settings for Ender 3v2 with Sprite Pro and CR Touch.

Physical settings:
X bed size: 215
Y bed size: 220
X min pos: 0
Y min pos: -5
X max pos: 215
Y max pos: 220
Z max pos: 235

Bed PID (you should run an auto-tune, but here's mine):
Set Kp: 98.27
Set Ki: 17.55
Set Kd: 366.86
Temp: 60
Pid Cycles: 5

Hotend PID (again - auto-tune, don't use mine, but for reference..):
Set Kp: 14.84
Set Ki: 1.13
Set Kd: 48.67
Temp: 230
Pid Cycles: 5

Probe Settings:
Probe X Offset: -31.4
Probe Y Offset: -40.1
Probe Z Offset: -2.76
Z Feed Rate: 480
Multi Probing: 2
Enable HS Mode: Yes

Mesh Leveling:
Mesh Points: 7x7
Fade Height: 10

Mesh Inset:
Mesh X Min: 10
Mesh X Max: 183.6
Mesh Y Min: 10
Mesh Y Max: 179.9

[ahtinurme]

Thank you, this works!

[ShoobyDooWupWup]

Signed up to GitHub just to say thank you for this. I bought a BambuLab and haven't used my E3 V2 for a while, decided to get it out and play around with it. Apart from the Z height (due to the type of bed more than likely) everything was perfect, did the PID's myself. Can't thank you enough for the BL Touch settings mate.

[nikopatel]

I'm running a self-compiled Ender3V2-422-BLTUBL-T13-LA-MPC. I'm working through configuring it, but used to run your firmware and can share most of the settings for Ender 3v2 with Sprite Pro and CR Touch.

Physical settings: X bed size: 215 Y bed size: 220 X min pos: 0 Y min pos: -5 X max pos: 215 Y max pos: 220 Z max pos: 235

Bed PID (you should run an auto-tune, but here's mine): Set Kp: 98.27 Set Ki: 17.55 Set Kd: 366.86 Temp: 60 Pid Cycles: 5

Hotend PID (again - auto-tune, don't use mine, but for reference..): Set Kp: 14.84 Set Ki: 1.13 Set Kd: 48.67 Temp: 230 Pid Cycles: 5

Probe Settings: Probe X Offset: -31.4 Probe Y Offset: -40.1 Probe Z Offset: -2.76 Z Feed Rate: 480 Multi Probing: 2 Enable HS Mode: Yes

Mesh Leveling: Mesh Points: 7x7 Fade Height: 10

Mesh Inset: Mesh X Min: 10 Mesh X Max: 183.6 Mesh Y Min: 10 Mesh Y Max: 179.9

Hi Awesome Helpful post.
could you please tell me if this settings (offcourse not the bedsize) will work for Ender 3/Ender 3 Pro on BTT SKR mini e3 V3.0 board?
and how to tune for PID for my board?

[b771x]

Thank you very much for detail answer I will set them and we will see. Dňa ne 23. 4. 2023 o 21:21 John Delisle ***@***.***> napísala(a):

…

I'm running a self-compiled Ender3V2-422-BLTUBL-T13-LA-MPC. I'm working through configuring it, but used to run your firmware and can share most of the settings for Ender 3v2 with Sprite. Physical settings: X bed size: 215 Y bed size: 220 X min pos: 0 Y min pos: -5 X max pos: 215 Y max pos: 220 Z max pos: 235 Bed PID (you should run an auto-tune, but here's mine): Set Kp: 98.27 Set Ki: 17.55 Set Kd: 366.86 Temp: 60 Pid Cycles: 5 Hotend PID (again - auto-tune, don't use mine, but for reference..): Set Kp: 14.84 Set Ki: 1.13 Set Kd: 48.67 Temp: 230 Pid Cycles: 5 Probe Settings: Probe X Offset: -31.4 Probe Y Offset: -40.1 Probe Z Offset: -2.76 Z Feed Rate: 480 Multi Probing: 2 Enable HS Mode: Yes Mesh Leveling: Mesh Points: 7x7 Fade Height: 10 Mesh Inset: Mesh X Min: 10 Mesh X Max: 183.6 Mesh Y Min: 10 Mesh Y Max: 179.9 — Reply to this email directly, view it on GitHub <#883 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AYM3UIDQNPUI4MJCGS6IFYDXCV6K7ANCNFSM6AAAAAAXIL24KM> . You are receiving this because you authored the thread.Message ID: ***@***.***>

[b771x]

My printer works well after new settings. Only MPC is maybe not ok. Please look at photo. Target was 200 but calibration ended on 217. Is it ok? Dňa po 24. 4. 2023 o 10:46 pribylinecm ***@***.***> napísala(a):

…

HelloJohn, thank you very much for detail answer I will set them and we will see. Br, Milan Dňa ne 23. 4. 2023 o 21:21 John Delisle ***@***.***> napísala(a): > I'm running a self-compiled Ender3V2-422-BLTUBL-T13-LA-MPC. I'm working > through configuring it, but used to run your firmware and can share most of > the settings for Ender 3v2 with Sprite. > > Physical settings: > X bed size: 215 > Y bed size: 220 > X min pos: 0 > Y min pos: -5 > X max pos: 215 > Y max pos: 220 > Z max pos: 235 > > Bed PID (you should run an auto-tune, but here's mine): > Set Kp: 98.27 > Set Ki: 17.55 > Set Kd: 366.86 > Temp: 60 > Pid Cycles: 5 > > Hotend PID (again - auto-tune, don't use mine, but for reference..): > Set Kp: 14.84 > Set Ki: 1.13 > Set Kd: 48.67 > Temp: 230 > Pid Cycles: 5 > > Probe Settings: > Probe X Offset: -31.4 > Probe Y Offset: -40.1 > Probe Z Offset: -2.76 > Z Feed Rate: 480 > Multi Probing: 2 > Enable HS Mode: Yes > > Mesh Leveling: > Mesh Points: 7x7 > Fade Height: 10 > > Mesh Inset: > Mesh X Min: 10 > Mesh X Max: 183.6 > Mesh Y Min: 10 > Mesh Y Max: 179.9 > > — > Reply to this email directly, view it on GitHub > <#883 (comment)>, > or unsubscribe > <https://github.com/notifications/unsubscribe-auth/AYM3UIDQNPUI4MJCGS6IFYDXCV6K7ANCNFSM6AAAAAAXIL24KM> > . > You are receiving this because you authored the thread.Message ID: > ***@***.***> >

[b771x]

IMG_1333