doc: specify release-7 branch in flake URLs

doc/manual/developing.rst

@@ -14,7 +14,7 @@ ARTIQ itself does not depend on Nix, and it is also possible to compile everythi
 * Install the `Nix package manager <http://nixos.org/nix/>`_, version 2.4 or later. Prefer a single-user installation for simplicity.
 * If you did not install Vivado in its default location ``/opt``, clone the ARTIQ Git repository and edit ``flake.nix`` accordingly.
 * Enable flakes in Nix by e.g. adding ``experimental-features = nix-command flakes`` to ``nix.conf`` (for example ``~/.config/nix/nix.conf``).
-* Enter the development shell by running ``nix develop git+https://github.com/m-labs/artiq.git``, or alternatively by cloning the ARTIQ Git repository and running ``nix develop`` at the root (where ``flake.nix`` is).
+* Enter the development shell by running ``nix develop git+https://github.com/m-labs/artiq.git\?ref=release-7``, or alternatively by cloning the ARTIQ Git repository and running ``nix develop`` at the root (where ``flake.nix`` is).
 * You can then build the firmware and gateware with a command such as ``$ python -m artiq.gateware.targets.kasli``. If you are using a JSON system description file, use ``$ python -m artiq.gateware.targets.kasli_generic file.json``.
 * Flash the binaries into the FPGA board with a command such as ``$ artiq_flash --srcbuild -d artiq_kasli -V <your_variant>``. You need to configure OpenOCD as explained :ref:`in the user section <configuring-openocd>`. OpenOCD is already part of the flake's development environment.
 * Check that the board boots and examine the UART messages by running a serial terminal program, e.g. ``$ flterm /dev/ttyUSB1`` (``flterm`` is part of MiSoC and installed in the flake's development environment). Leave the terminal running while you are flashing the board, so that you see the startup messages when the board boots immediately after flashing. You can also restart the board (without reflashing it) with ``$ artiq_flash start``.

doc/manual/installing.rst

@@ -21,7 +21,7 @@ Once Nix is installed, enable Flakes: ::
   $ mkdir -p ~/.config/nix
   $ echo "experimental-features = nix-command flakes" > ~/.config/nix/nix.conf
 
-The easiest way to obtain ARTIQ is then to install it into the user environment with ``$ nix profile install git+https://github.com/m-labs/artiq.git``. Answer "Yes" to the questions about setting Nix configuration options. This provides a minimal installation of ARTIQ where the usual commands (``artiq_master``, ``artiq_dashboard``, ``artiq_run``, etc.) are available.
+The easiest way to obtain ARTIQ is then to install it into the user environment with ``$ nix profile install git+https://github.com/m-labs/artiq.git\?ref=release-7``. Answer "Yes" to the questions about setting Nix configuration options. This provides a minimal installation of ARTIQ where the usual commands (``artiq_master``, ``artiq_dashboard``, ``artiq_run``, etc.) are available.
 
 This installation is however quite limited, as Nix creates a dedicated Python environment for the ARTIQ commands alone. This means that other useful Python packages that you may want (pandas, matplotlib, ...) are not available to them.
 
@@ -30,8 +30,8 @@ Installing multiple packages and making them visible to the ARTIQ commands requi
 ::
 
   {
-    inputs.artiq.url = "git+https://github.com/m-labs/artiq.git";
-    inputs.extrapkg.url = "git+https://git.m-labs.hk/M-Labs/artiq-extrapkg.git";
+    inputs.artiq.url = "git+https://github.com/m-labs/artiq.git?ref=release-7";
+    inputs.extrapkg.url = "git+https://git.m-labs.hk/M-Labs/artiq-extrapkg.git?ref=release-7";
     inputs.extrapkg.inputs.artiq.follows = "artiq";
     outputs = { self, artiq, extrapkg }:
       let