marlin 2.1.2 octopus powerloss psu smart sensor bltouch firmware

printer.cfg voor klipper tronxy x5sa 2ec330x330 vind u hier onder.gebruikte run out sensoren btt smart sensor 2.0 opgelet lees u eigen mcu nummer uit en schrijf de huidige in de printer cfg hier mee over

klipper printer cfg.

include fluidd.cfg] [include mainsail.cfg]

This file contains common pin mappings for the BigTreeTech Octopus.

To use this config, the firmware should be compiled for the

STM32F446 with a "32KiB bootloader" and a "12MHz crystal" clock reference.

See docs/Config_Reference.md for a description of parameters.

[virtual_sdcard] path: /home/gijs/printer_data/gcodes

[display_status]

[pause_resume]

[gcode_macro CANCEL_PRINT] description: Cancel the actual running print rename_existing: CANCEL_PRINT_BASE gcode: TURN_OFF_HEATERS CANCEL_PRINT_BASE

[duplicate_pin_override] pins: PA2, PF4

Driver0

[stepper_x] step_pin: PF13 dir_pin: PF12 enable_pin: !PF14 microsteps: 16 rotation_distance: 80 endstop_pin: !PG6 position_endstop: 0 position_max: 330 homing_speed: 50

Driver1

[stepper_y] step_pin: PG0 dir_pin: PG1 enable_pin: !PF15 microsteps: 16 rotation_distance: 80 endstop_pin: !PG9 position_endstop: 0 position_max: 330 homing_speed: 50

Driver2

[stepper_z] step_pin: PF11 dir_pin: !PG3 enable_pin: !PG5 microsteps: 16 rotation_distance: 16 endstop_pin: probe:z_virtual_endstop position_min: -15 position_max: 395

Driver3

The Octopus only has 4 heater outputs which leaves an extra stepper

This can be used for a second Z stepper, dual_carriage, extruder co-stepper,

or other accesory such as an MMU

[stepper_z1] step_pin: PG4 dir_pin: !PC1 enable_pin: !PA0 microsteps: 16 rotation_distance: 16

#...

########################

BL Touch

########################

A [probe] section can be defined instead with a pin: setting identical

to the sensor_pin: for a bltouch

[bltouch] control_pin: PB6 sensor_pin: PE9 x_offset: -43 y_offset: -6 #z_offset: 3.0

uncomment these to speed up testing, though some BLTouchs wont work reliably (i.e. mine)

stow_on_each_sample: false

probe_with_touch_mode: true

Inductive Probe, comment out if using BLTouch

[probe]

pin: ~!PC5

x_offset: -40

y_offset: -7

# z_offset: 3.71

z_offset: 4.54

speed: 10.0

samples: 3

samples_result: median

# sample_retract_dist: 3.0

samples_tolerance: 0.01

samples_tolerance_retries: 3

[safe_z_home] home_xy_position: 205,165 speed: 150 z_hop: 10 z_hop_speed: 10

[bed_screws]

screw1: 5,5

screw2: 165,5

screw3: 325,5

screw4: 5,325

screw5: 165,325

screw6: 325,325

[screws_tilt_adjust] speed: 150 screw1: 45,12 screw2: 210,12 screw3: 350,12 screw4: 45,330 screw5: 210,330 screw6: 350,330

[bed_mesh] speed: 150 probe_count: 5,5 mesh_min : 20,20 mesh_max : 300,300

horizontal_move_z: 6

algorithm: lagrange

########################

Z Tilt

########################

[z_tilt] z_positions:-90,165 420,165 points: 90,165 327,165 speed: 200 horizontal_move_z: 10 retries: 5 retry_tolerance: .005

########################

Mesh Bed Leveling

########################

[bed_mesh] speed: 200 horizontal_move_z: 6 mesh_min: 45, 45 mesh_max: 280, 280 probe_count: 5, 5

###########################

SCREWS_TILT_CALCULATE

###########################

[screws_tilt_adjust] screw1: 90,45 screw1_name: left front screw2: 90,285 screw2_name: left back screw3: 330,285 screw3_name: right back screw4: 330,45 screw4_name: right front speed: 100 horizontal_move_z: 5 screw_thread: CCW-M3

########################

Extruder

########################

Driver4 (Extruder 0 / T0)

[extruder] step_pin: PF9 dir_pin: PF10 enable_pin: !PG2 full_steps_per_rotation: 200 microsteps: 16 rotation_distance: 14.797544011113
nozzle_diameter: 0.400 filament_diameter: 1.750 heater_pin: PA2 # HE0 sensor_pin: PF4 # T0 sensor_type: EPCOS 100K B57560G104F control: pid pid_Kp: 16.165 pid_Ki: 0.623 pid_Kd: 104.872 min_temp: 0 max_temp: 260 min_extrude_temp: 180 max_extrude_only_distance: 150 pressure_advance: 0.60 pressure_advance_smooth_time: 0.080

[filament_switch_sensor switch_sensor] switch_pin: gpio_PG13 pause_on_runout: False runout_gcode: PAUSE # [pause_resume] is required in printer.cfg M117 Filament switch runout insert_gcode: M117 Filament switch inserted

[filament_motion_sensor encoder_sensor] switch_pin: gpio_12 detection_length: 2.88 extruder: extruder pause_on_runout: False runout_gcode: PAUSE # [pause_resume] is required in printer.cfg M117 Filament encoder runout insert_gcode: M117 Filament encoder inserted

Driver5 (Extruder 1 / T1)

[extruder1] step_pin: PC13 dir_pin: PF0 enable_pin: !PF1 full_steps_per_rotation: 200 microsteps: 16 rotation_distance: 15.377839854686 nozzle_diameter: 0.400 filament_diameter: 1.750 heater_pin: PA2 # HE0 sensor_pin: PF4 # T0 sensor_type: EPCOS 100K B57560G104F control: pid pid_Kp: 16.165 pid_Ki: 0.623 pid_Kd: 104.872 min_temp: 0 max_temp: 260 min_extrude_temp: 180 max_extrude_only_distance: 150 pressure_advance: 0.60 pressure_advance_smooth_time: 0.080

[filament_switch_sensor switch_sensor] switch_pin: gpio_PG13 pause_on_runout: False runout_gcode: PAUSE # [pause_resume] is required in printer.cfg M117 Filament switch runout insert_gcode: M117 Filament switch inserted

[filament_motion_sensor encoder_sensor] switch_pin: gpio_14 detection_length: 2.88 extruder: extruder pause_on_runout: False runout_gcode: PAUSE # [pause_resume] is required in printer.cfg M117 Filament encoder runout insert_gcode: M117 Filament encoder inserted

[gcode_macro T0] gcode: SYNC_EXTRUDER_MOTION EXTRUDER="extruder" MOTION_QUEUE="extruder" SYNC_EXTRUDER_MOTION EXTRUDER="extruder1" MOTION_QUEUE="" #SYNC_EXTRUDER_MOTION EXTRUDER="extruder2" MOTION_QUEUE="" #SYNC_EXTRUDER_MOTION EXTRUDER="extruder3" MOTION_QUEUE="" #SYNC_EXTRUDER_MOTION EXTRUDER="extruder4" MOTION_QUEUE=""

[gcode_macro T1] gcode: SYNC_EXTRUDER_MOTION EXTRUDER="extruder" MOTION_QUEUE="" SYNC_EXTRUDER_MOTION EXTRUDER="extruder1" MOTION_QUEUE="extruder" #SYNC_EXTRUDER_MOTION EXTRUDER="extruder2" MOTION_QUEUE="" #SYNC_EXTRUDER_MOTION EXTRUDER="extruder3" MOTION_QUEUE="" #SYNC_EXTRUDER_MOTION EXTRUDER="extruder4" MOTION_QUEUE=""

[delayed_gcode STARTUP_GCODE] initial_duration: 0.1 gcode: {% set svv = printer.save_variables.variables %} {% if svv.active_tool != "" %} { svv.active_tool } {% else %} T0 {% endif %} { action_respond_info("Active Tool: " + svv.active_tool) } set_pressure_advance extruder=extruder advance=0.60 smooth_time=0.08 set_pressure_advance extruder=extruder1 advance=0.60 smooth_time=0.08 #set_pressure_advance extruder=extruder2 advance=0.60 smooth_time=0.08 #set_pressure_advance extruder=extruder3 advance=0.60 smooth_time=0.08 #set_pressure_advance extruder=extruder4 advance=0.60 smooth_time=0.08

Driver6

#[extruder2] #step_pin: PE2 #dir_pin: PE3 #enable_pin: !PD4 #heater_pin: PB10 # HE2 #sensor_pin: PF6 # T2 #...

#[filament_switch_sensor material_2] #switch_pin: PG14

Driver7

#[extruder3] #step_pin: PE6 #dir_pin: PA14 #enable_pin: !PE0 #heater_pin: PB11 # HE3 #sensor_pin: PF7 # T3 #...

#[filament_switch_sensor material_3] #switch_pin: PG15

[heater_bed] heater_pin: PA1 sensor_pin: PF3 # TB sensor_type: ATC Semitec 104GT-2 #control: watermark control: pid pid_Kp: 72.003 pid_Ki: 1.616 pid_Kd: 801.935 min_temp: 0 max_temp: 130

[fan] pin: PA8

[heater_fan fan1] pin: PE5

[heater_fan fan2] pin: PD12

#[heater_fan fan3] #pin: PD13

#[heater_fan fan4] #pin: PD14

#[controller_fan fan5] #pin: PD15

[mcu] serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_47005E000451373330333137-if00

CAN bus is also available on this board

[printer] kinematics: corexy max_velocity: 300 max_accel: 3000 max_z_velocity: 5 max_z_accel: 100

[heater_bed] heater_pin: PA1 sensor_pin: PF3 # TB sensor_type: ATC Semitec 104GT-2 #control: watermark #control: pid

min_temp: 0 max_temp: 130

[fan] pin: PA8

[heater_fan fan1] pin: PE5

[heater_fan fan2] pin: PD12

#[heater_fan fan3] #pin: PD13

#[heater_fan fan4] #pin: PD14

#[controller_fan fan5] #pin: PD15

[mcu] serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_200046001450535556323420-if00

CAN bus is also available on this board

[printer] kinematics: corexy max_velocity: 300 max_accel: 3000 max_z_velocity: 5 max_z_accel: 100

########################################

TMC2209 configuration

######################################## [tmc2209 stepper_x] uart_pin: PC4 diag_pin: PG6 run_current: 0.800

[tmc2209 stepper_y] uart_pin: PD11 diag_pin: PG9 run_current: 0.800

[tmc2209 stepper_z] uart_pin: PC6 diag_pin: PG10 run_current: 0.650 stealthchop_threshold: 999999

[tmc2209 stepper_z1] uart_pin: PC7 diag_pin: PG11 run_current: 0.650 stealthchop_threshold: 999999

[tmc2209 extruder] uart_pin: PF2 run_current: 0.800 stealthchop_threshold: 999999

[tmc2209 extruder1] uart_pin: PE4 run_current: 0.800 stealthchop_threshold: 999999

#[tmc2209 extruder2] #uart_pin: PE1 #run_current: 0.800 #stealthchop_threshold: 999999

#[tmc2209 extruder3] #uart_pin: PD3 #run_current: 0.800 #stealthchop_threshold: 999999

########################################

TMC2130 configuration

########################################

#[tmc2130 stepper_x] #cs_pin: PC4 #spi_bus: spi1 ##diag1_pin: PG6 #run_current: 0.800 #stealthchop_threshold: 999999

#[tmc2130 stepper_y] #cs_pin: PD11 #spi_bus: spi1 ##diag1_pin: PG9 #run_current: 0.800 #stealthchop_threshold: 999999

#[tmc2130 stepper_z] #cs_pin: PC6 #spi_bus: spi1 ##diag1_pin: PG10 #run_current: 0.650 #stealthchop_threshold: 999999

#[tmc2130 stepper_] #cs_pin: PC7 #spi_bus: spi1 ##diag1_pin: PG11 #run_current: 0.800 #stealthchop_threshold: 999999

#[tmc2130 extruder] #cs_pin: PF2 #spi_bus: spi1 #run_current: 0.800 #stealthchop_threshold: 999999

#[tmc2130 extruder1] #cs_pin: PE4 #spi_bus: spi1 #run_current: 0.800 #stealthchop_threshold: 999999

#[tmc2130 extruder2] #cs_pin: PE1 #spi_bus: spi1 #run_current: 0.800 #stealthchop_threshold: 999999

#[tmc2130 extruder3] #cs_pin: PD3 #spi_bus: spi1 #run_current: 0.800 #stealthchop_threshold: 999999

[board_pins] aliases: # EXP1 header EXP1_1=PE8, EXP1_2=PE7, EXP1_3=PE9, EXP1_4=PE10, EXP1_5=PE12, EXP1_6=PE13, # Slot in the socket on this side EXP1_7=PE14, EXP1_8=PE15, EXP1_9=, EXP1_10=<5V>,

# EXP2 header
EXP2_1=PA6, EXP2_2=PA5,
EXP2_3=PB1, EXP2_4=PA4,
EXP2_5=PB2, EXP2_6=PA7,      # Slot in the socket on this side
EXP2_7=PC15, EXP2_8=<RST>,
EXP2_9=<GND>, EXP2_10=PC5

See the sample-lcd.cfg file for definitions of common LCD displays.

#[neopixel my_neopixel] #pin: PB0

## <---------------------- SAVE_CONFIG ----------------------> ## DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. ## ## [bed_mesh default] ## version = 1 ## points = ## 0.050000, 0.025000, 0.020000, 0.020000, 0.035000 ## -0.005000, -0.070000, -0.120000, -0.060000, -0.080000 ## -0.045000, -0.100000, -0.090000, -0.085000, -0.105000 ## -0.145000, -0.185000, -0.195000, -0.200000, -0.185000 ## -0.035000, -0.115000, -0.120000, -0.100000, -0.040000 ## tension = 0.2 ## min_x = 45.0 ## algo = lagrange ## y_count = 5 ## mesh_y_pps = 2 ## min_y = 45.0 ## x_count = 5 ## max_y = 280.0 ## mesh_x_pps = 2 ## max_x = 280.0 ## ## [extruder] ## ## [heater_bed] ## ## [bltouch] ## z_offset = 2.080 ## ## [extruder1] #*#