Skip to content

Arduino library to interface to JQ8400 (JQ8400-FL, JQ8400-TF) Mp3 Player Modules

License

Notifications You must be signed in to change notification settings

gpb01/JQ8400_Serial

 
 

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

49 Commits
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

JQ8400_Serial

Simple to use Arduino library to interface to JQ8400 (JQ8400-FL, JQ8400-TF) Mp3 Player Modules

Table of Contents

JQ8400-TF JQ8400-FL

Download, Install and Example

  • Download: http://sparks.gogo.co.nz/JQ8400_Serial.zip
  • Open the Arduino IDE (1.6+)
  • Select the menu item Sketch > Import Library > Add Library
  • Choose to install the JQ8400_Serial.zip file you downloaded
  • Now you can choose File > Examples > JQ8400_Serial > HelloWorld

Connecting To Your Arduino

The JQ8400_Serial library can be configured to talk through any "Serial" port, including "SoftwareSerial", anything that is a Stream.

Most commonly you will use a SoftwareSerial with typical "AVR" based Arduinos that only have one hardware seral port. For Arduino's (and related, like ESP32) that have more than one hardware serial port you will typically want to use one of those instead of SoftwareSerial.

The most important consideration is that if your Arduino is 5 volt, you will want to put a 1k resistor on the RX pin of the JQ8400 and the Arduino's appropriate TX pin you are using.

Below are some examples to help you.

For a SoftwareSerial Connection

This is the typical setup where you have an Arduino Uno or Nano etc which only has one "Hardware" serial port and you use that to upload and communicate to the Arduino yourself, therefore we use a SoftwareSerial connection to communicate between the Arduino and the JQ8400 Module.

SoftwareSerial 5v Arduino, connect as follows.

JQ8400 Module Arduino
RX through a 1K Resistor then to pin 9
TX pin 8
GND (any of) GND
VCC (any of) VCC

SoftwareSerial 3v3 Arduino, connect as follows...

JQ8400 Module Arduino
RX pin 9
TX pin 8
GND (any of) GND
VCC (any of) VCC

You can use pins other than 9 and 8 if you wish, simply set them in your code, which looks something like this...

#include <SoftwareSerial.h>
SoftwareSerial mySerial(8,9);

#include <JQ8400_Serial.h>
JQ8400_Serial mp3(mySerial);

void setup()
{
  mySerial.begin(9600); // We must talk to the JQ8400 at 9600
  mp3.reset();          // Reset the device (optional, recommended)
}

void loop()
{
  // You should do more interesting stuff than just this...
  mp3.next();
  while(mp3.busy()); // Wait until finished.
}

For a built in additional hardware serial connection (eg ESP32)

This is a typical setup where your Arduino environment has more than one "Serial", and you want to use one of those to communicate to the JQ8400, leaving the normal "Serial" free for uploading, communication to the Arduino etc...

Built In Additional Serial on 5v Arduino, connect as follows.

JQ8400 Module Arduino
RX through a 1K Resistor then to appropriate TX pin
TX RX pin
GND (any of) GND
VCC (any of) VCC

Built In Additional Serial on 3v3 Arduino, connect as follows.

JQ8400 Module Arduino
RX appropriate TX pin
TX appropriate RX pin
GND (any of) GND
VCC (any of) VCC

Example for ESP32 using Built In Serial2

JQ8400 Module ESP32
RX GPIO17
TX GPIO16
GND (any of) GND
VCC (any of) VCC

Example Code For "Serial2"

#include <JQ8400_Serial.h>
JQ8400_Serial mp3(Serial2);

void setup()
{
  Serial2.begin(9600);  // We must talk to the JQ8400 at 9600 - maybe you need to add some extra parameters to begin, consult your specific board's documents if you have trouble.
  mp3.reset();          // Reset the device (optional, recommended)
}

void loop()
{
  // You should do more interesting stuff than just this...
  mp3.next();
  while(mp3.busy()); // Wait until finished.
}

Troubleshooting

People have problems in about this order...

  1. Incorrectly wired, make sure that TX/RX crossover and that you have GND shared
  2. Insufficient power supply. The power demands are not insignificant, USB from a computer... likely not good enough. Use external power.
  3. Trying to upload to JQ8400 while it is still connected to the Arduino. Best to unplug the JQ8400 from your project and just have it plugged into a USB cable when you want to change the files on it.
  4. MP3 file problem. Try re-encoding your MP3 files.

Further Documentation and Library Reference

JQ6500 to JQ8400 Breaking Changes

This section is for users of previous JQ6500 devices and the JQ6500_Serial library who are transitioning to a JQ8400 with JQ8400_Serial library.

As much as possible the JQ8400_Serial library should follow the same "api", with some additions, however there are some "breaking changes" you should be aware of...

  • The initialisation has changed so that you can (must) point the JQ8400 library to a specific serial connection to the JQ8400 player, you can use SoftwareSerial, or any of your other serial ports (or any Stream). This enables you to use devices that do not support SoftwareSerial.

Example for software serial on pins 8 and 9...

#include <SoftwareSerial.h>
SoftwareSerial  mySerial(8,9);
  
#include <JQ8400_Serial.h>
JQ8400_Serial   mp3(mySerial);

void setup()
{
  mySerial.begin(9600);
  mp3.reset();
}

Example over microcontroller's default hardware serial port...

#include <JQ8400_Serial.h>
JQ8400_Serial   mp3(Serial);

void setup()
{
  Serial.begin(9600);
  mp3.reset();
}

Example over microcontroller's other hardware serial port...

#include <JQ8400_Serial.h>
JQ8400_Serial   mp3(Serial2);

void setup()
{
  Serial2.begin(9600);
  mp3.reset();
}
  • JQ8400 does not support countFolders() at all (AFAIK) therefore this method is not available..
  • JQ8400 is not given a source for countFiles - that is use mp3.countFiles() not mp3.countFiles(MP3_SRC_SDCARD), use mp3.setSource(MP3_SRC_SDCARD) to change the source before counting if you are not already on that source.
  • JQ8400 does not support MP3_EQ_BASS

About

Arduino library to interface to JQ8400 (JQ8400-FL, JQ8400-TF) Mp3 Player Modules

Resources

License

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published

Languages

  • C++ 100.0%