-
Notifications
You must be signed in to change notification settings - Fork 324
Commit
This commit does not belong to any branch on this repository, and may belong to a fork outside of the repository.
ath79-generic: Add support for OpenMesh OM5P-AC v2
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/200 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* 4x GPIO-LEDs (3x wifi, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
- eth0
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as LAN interface
- eth1
+ AR8031 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Gluon image name change
=======================
The device had the image name "openmesh-om5p-acv2" in older versions of Gluon.
This had to be changed with the new name in the device trees of the ath79
device tree.- Loading branch information
Showing
3 changed files
with
343 additions
and
1 deletion.
There are no files selected for viewing
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| Original file line number | Diff line number | Diff line change |
|---|---|---|
|
|
@@ -41,7 +41,7 @@ ath79-generic | |
| - OM2P-LC | ||
| - OM5P | ||
| - OM5P-AN | ||
| - OM5P-AC (v1) | ||
| - OM5P-AC (v1, v2) | ||
|
|
||
| * Plasma Cloud | ||
|
|
||
|
|
||
337 changes: 337 additions & 0 deletions
337
patches/openwrt/0013-ath79-Add-support-for-OpenMesh-OM5P-AC-v2.patch
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| Original file line number | Diff line number | Diff line change |
|---|---|---|
| @@ -0,0 +1,337 @@ | ||
| From: Sven Eckelmann <sven@narfation.org> | ||
| Date: Mon, 23 Nov 2020 13:41:34 +0100 | ||
| Subject: ath79: Add support for OpenMesh OM5P-AC v2 | ||
|
|
||
| Device specifications: | ||
| ====================== | ||
|
|
||
| * Qualcomm/Atheros QCA9558 ver 1 rev 0 | ||
| * 720/600/200 MHz (CPU/DDR/AHB) | ||
| * 128 MB of RAM | ||
| * 16 MB of SPI NOR flash | ||
| - 2x 7 MB available; but one of the 7 MB regions is the recovery image | ||
| * 2T2R 2.4 GHz Wi-Fi (11n) | ||
| * 2T2R 5 GHz Wi-Fi (11ac) | ||
| * 4x GPIO-LEDs (3x wifi, 1x power) | ||
| * 1x GPIO-button (reset) | ||
| * external h/w watchdog (enabled by default)) | ||
| * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) | ||
| * TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring | ||
| * 2x ethernet | ||
| - eth0 | ||
| + AR8035 ethernet PHY (RGMII) | ||
| + 10/100/1000 Mbps Ethernet | ||
| + 802.3af POE | ||
| + used as LAN interface | ||
| - eth1 | ||
| + AR8031 ethernet PHY (RGMII) | ||
| + 10/100/1000 Mbps Ethernet | ||
| + 18-24V passive POE (mode B) | ||
| + used as WAN interface | ||
| * 12-24V 1A DC | ||
| * internal antennas | ||
|
|
||
| Flashing instructions: | ||
| ====================== | ||
|
|
||
| Various methods can be used to install the actual image on the flash. | ||
| Two easy ones are: | ||
|
|
||
| ap51-flash | ||
| ---------- | ||
|
|
||
| The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be | ||
| used to transfer the image to the u-boot when the device boots up. | ||
|
|
||
| initramfs from TFTP | ||
| ------------------- | ||
|
|
||
| The serial console must be used to access the u-boot shell during bootup. | ||
| It can then be used to first boot up the initramfs image from a TFTP server | ||
| (here with the IP 192.168.1.21): | ||
|
|
||
| setenv serverip 192.168.1.21 | ||
| setenv ipaddr 192.168.1.1 | ||
| tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr | ||
|
|
||
| The actual sysupgrade image can then be transferred (on the LAN port) to the | ||
| device via | ||
|
|
||
| scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ | ||
|
|
||
| On the device, the sysupgrade must then be started using | ||
|
|
||
| sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin | ||
|
|
||
| Signed-off-by: Sven Eckelmann <sven@narfation.org> | ||
| Forwarded: https://github.com/openwrt/openwrt/pull/3720 | ||
|
|
||
| diff --git a/target/linux/ath79/dts/qca9558_openmesh_om5p-ac-v2.dts b/target/linux/ath79/dts/qca9558_openmesh_om5p-ac-v2.dts | ||
| index b4d452dda19de7986f75f1e7a6f647b1d517014d..a478f04a74a18a966f8b962f17abc8560b19f6b3 100644 | ||
| --- a/target/linux/ath79/dts/qca9558_openmesh_om5p-ac-v2.dts | ||
| +++ b/target/linux/ath79/dts/qca9558_openmesh_om5p-ac-v2.dts | ||
| @@ -7,26 +7,34 @@ | ||
|
|
||
| / { | ||
| compatible = "openmesh,om5p-ac-v2", "qca,qca9558"; | ||
| - model = "OpenMesh OM5P-AC V2"; | ||
| + model = "OpenMesh OM5P-AC v2"; | ||
|
|
||
| - extosc: ref { | ||
| - compatible = "fixed-clock"; | ||
| - #clock-cells = <0>; | ||
| - clock-output-names = "ref"; | ||
| - clock-frequency = <40000000>; | ||
| + chosen { | ||
| + /delete-property/ bootargs; | ||
| + }; | ||
| + | ||
| + aliases { | ||
| + serial0 = &uart; | ||
| + led-boot = &led_power_blue; | ||
| + led-failsafe = &led_power_blue; | ||
| + led-running = &led_power_blue; | ||
| + led-upgrade = &led_power_blue; | ||
| + label-mac-device = ð0; | ||
| }; | ||
|
|
||
| leds { | ||
| compatible = "gpio-leds"; | ||
|
|
||
| - power { | ||
| - label = "blue:power"; | ||
| - gpios = <&gpio 14 GPIO_ACTIVE_LOW>; | ||
| - }; | ||
| - | ||
| wifi_green { | ||
| label = "green:wifi"; | ||
| gpios = <&gpio 13 GPIO_ACTIVE_LOW>; | ||
| + linux,default-trigger = "phy0tpt"; | ||
| + }; | ||
| + | ||
| + led_power_blue: power_blue { | ||
| + label = "blue:power"; | ||
| + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; | ||
| + default-state = "on"; | ||
| }; | ||
|
|
||
| wifi_yellow { | ||
| @@ -50,6 +58,32 @@ | ||
| }; | ||
| }; | ||
|
|
||
| + i2c { | ||
| + compatible = "i2c-gpio"; | ||
| + gpios = <&gpio 19 GPIO_ACTIVE_HIGH /* sda */ | ||
| + &gpio 18 GPIO_ACTIVE_HIGH /* scl */ | ||
| + >; | ||
| + #address-cells = <1>; | ||
| + #size-cells = <0>; | ||
| + | ||
| + i2c-gpio,scl-open-drain; | ||
| + i2c-gpio,sda-open-drain; | ||
| + | ||
| + tmp423a@4e { | ||
| + compatible = "ti,tmp423"; | ||
| + reg = <0x4e>; | ||
| + }; | ||
| + }; | ||
| + | ||
| + watchdog { | ||
| + compatible = "linux,wdt-gpio"; | ||
| + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; | ||
| + hw_algo = "toggle"; | ||
| + /* hw_margin_ms is actually 300s but driver limits it to 60s */ | ||
| + hw_margin_ms = <60000>; | ||
| + always-running; | ||
| + }; | ||
| + | ||
| gpio-export { | ||
| compatible = "gpio-export"; | ||
| #size-cells = <0>; | ||
| @@ -69,11 +103,11 @@ | ||
|
|
||
| &pinmux { | ||
| pinmux_pa_dcdc_pins { | ||
| - pinctrl-single,bits = <0x0 0xff00 0x0>; | ||
| + pinctrl-single,bits = <0x0 0x0 0xff0000>; | ||
| }; | ||
|
|
||
| pinmux_pa_high_pins { | ||
| - pinctrl-single,bits = <0x10 0xff 0x0>; | ||
| + pinctrl-single,bits = <0x10 0x0 0xff>; | ||
| }; | ||
| }; | ||
|
|
||
| @@ -81,10 +115,6 @@ | ||
| status = "okay"; | ||
| }; | ||
|
|
||
| -&pll { | ||
| - clocks = <&extosc>; | ||
| -}; | ||
| - | ||
| &spi { | ||
| status = "okay"; | ||
|
|
||
| @@ -93,6 +123,7 @@ | ||
| reg = <0>; | ||
| spi-max-frequency = <25000000>; | ||
|
|
||
| + /* partitions are passed via bootloader */ | ||
| partitions { | ||
| compatible = "fixed-partitions"; | ||
| #address-cells = <1>; | ||
| @@ -104,19 +135,29 @@ | ||
| read-only; | ||
| }; | ||
|
|
||
| - partition@1 { | ||
| + partition@40000 { | ||
| label = "u-boot-env"; | ||
| reg = <0x040000 0x010000>; | ||
| }; | ||
|
|
||
| - partition@2 { | ||
| - compatible = "denx,uimage"; | ||
| - label = "firmware"; | ||
| + partition@50000 { | ||
| + label = "custom"; | ||
| + reg = <0x050000 0x060000>; | ||
| + read-only; | ||
| + }; | ||
| + | ||
| + partition@b0000 { | ||
| + label = "inactive"; | ||
| + reg = <0x0b0000 0x7a0000>; | ||
| + }; | ||
| + | ||
| + partition@850000 { | ||
| + label = "inactive2"; | ||
| reg = <0x850000 0x7a0000>; | ||
| }; | ||
|
|
||
| - partition@3 { | ||
| - label = "art"; | ||
| + art: partition@ff0000 { | ||
| + label = "ART"; | ||
| reg = <0xff0000 0x010000>; | ||
| read-only; | ||
| }; | ||
| @@ -127,18 +168,25 @@ | ||
| &mdio0 { | ||
| status = "okay"; | ||
|
|
||
| + phy-mask = <0x10>; | ||
| + | ||
| phy4: ethernet-phy@4 { | ||
| reg = <4>; | ||
| - phy-mode = "rgmii-id"; | ||
| + eee-broken-100tx; | ||
| + eee-broken-1000t; | ||
| }; | ||
| }; | ||
|
|
||
| &mdio1 { | ||
| status = "okay"; | ||
|
|
||
| + phy-mask = <0x2>; | ||
| + | ||
| phy1: ethernet-phy@1 { | ||
| reg = <1>; | ||
| - phy-mode = "sgmii"; | ||
| + eee-broken-100tx; | ||
| + eee-broken-1000t; | ||
| + at803x-override-sgmii-link-check; | ||
| }; | ||
| }; | ||
|
|
||
| @@ -147,7 +195,19 @@ | ||
|
|
||
| pll-data = <0x82000101 0x80000101 0x80001313>; | ||
|
|
||
| + mtd-mac-address = <&art 0x0>; | ||
| + | ||
| + phy-mode = "rgmii-id"; | ||
| phy-handle = <&phy4>; | ||
| + | ||
| + gmac-config { | ||
| + device = <&gmac>; | ||
| + rgmii-enabled = <1>; | ||
| + rxd-delay = <2>; | ||
| + rxdv-delay = <2>; | ||
| + txd-delay = <0>; | ||
| + txen-delay = <0>; | ||
| + }; | ||
| }; | ||
|
|
||
| ð1 { | ||
| @@ -155,5 +215,17 @@ | ||
|
|
||
| pll-data = <0x03000101 0x80000101 0x80001313>; | ||
|
|
||
| + mtd-mac-address = <&art 0x6>; | ||
| + | ||
| + qca955x-sgmii-fixup; | ||
| + | ||
| phy-handle = <&phy1>; | ||
| }; | ||
| + | ||
| +&wmac { | ||
| + status = "okay"; | ||
| + | ||
| + mtd-cal-data = <&art 0x1000>; | ||
| + mtd-mac-address = <&art 0x0>; | ||
| + mac-address-increment = <2>; | ||
| +}; | ||
| diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata | ||
| index 80f9dcf49f8b63f962b82c4a404ed4084d713e81..510f7cc2a8a0bf3dd0eafdfa7fd3e31fa4da19a5 100644 | ||
| --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata | ||
| +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata | ||
| @@ -102,12 +102,9 @@ case "$FIRMWARE" in | ||
| openmesh,a40|\ | ||
| openmesh,a60|\ | ||
| openmesh,mr1750-v1|\ | ||
| - openmesh,mr1750-v2) | ||
| - caldata_extract "ART" 0x5000 0x844 | ||
| - ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16) | ||
| - ;; | ||
| + openmesh,mr1750-v2|\ | ||
| openmesh,om5p-ac-v2) | ||
| - caldata_extract "art" 0x5000 0x844 | ||
| + caldata_extract "ART" 0x5000 0x844 | ||
| ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16) | ||
| ;; | ||
| qihoo,c301) | ||
| diff --git a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh | ||
| index 98583a67810258a2aca7f2eadc85c770e33fe1dc..67e53c5fdebf29e71b920753be829fa4e41ca207 100644 | ||
| --- a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh | ||
| +++ b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh | ||
| @@ -83,6 +83,7 @@ platform_do_upgrade() { | ||
| openmesh,om2p-lc|\ | ||
| openmesh,om5p|\ | ||
| openmesh,om5p-ac-v1|\ | ||
| + openmesh,om5p-ac-v2|\ | ||
| openmesh,om5p-an) | ||
| PART_NAME="inactive" | ||
| platform_do_upgrade_openmesh "$1" | ||
| diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk | ||
| index 890792ae6f8c8e59fef9c2f78d1a57dbecb9e1d0..64b619e5eab4dc2b33146060eca7c8da5b3c1fc0 100644 | ||
| --- a/target/linux/ath79/image/generic.mk | ||
| +++ b/target/linux/ath79/image/generic.mk | ||
| @@ -1822,12 +1822,12 @@ endef | ||
| TARGET_DEVICES += openmesh_om5p-ac-v1 | ||
|
|
||
| define Device/openmesh_om5p-ac-v2 | ||
| + $(Device/openmesh_common_64k) | ||
| SOC := qca9558 | ||
| - DEVICE_VENDOR := OpenMesh | ||
| DEVICE_MODEL := OM5P-AC | ||
| DEVICE_VARIANT := v2 | ||
| - DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct om-watchdog | ||
| - IMAGE_SIZE := 7808k | ||
| + DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct | ||
| + OPENMESH_CE_TYPE := OM5PAC | ||
| SUPPORTED_DEVICES += om5p-acv2 | ||
| endef | ||
| TARGET_DEVICES += openmesh_om5p-ac-v2 |
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters