Add initial support for the KSZ8795 Ethernet switch on the RevPi Flat #2

l1k · 2020-08-10T13:23:33Z

No description provided.

The KSZ8051 PHY and the KSZ8794/KSZ8795/KSZ8765 switch share exactly the same PHY ID. Since KSZ8051 is higher in the ksphy_driver[] list of PHYs in the micrel PHY driver, it is used even with the KSZ87xx switch. This is wrong, since the KSZ8051 configures registers of the PHY which are not present on the simplified KSZ87xx switch PHYs and misconfigures other registers of the KSZ87xx switch PHYs. Fortunatelly, it is possible to tell apart the KSZ8051 PHY from the KSZ87xx switch by checking the Basic Status register Bit 0, which is read-only and indicates presence of the Extended Capability Registers. The KSZ8051 PHY has those registers while the KSZ87xx switch does not. This patch implements simple check for the presence of this bit for both the KSZ8051 PHY and KSZ87xx switch, to let both use the correct PHY driver instance. Fixes: 9d162ed ("net: phy: micrel: add support for KSZ8795") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Andrew Lunn <andrew@lunn.ch> Cc: David S. Miller <davem@davemloft.net> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: George McCollister <george.mccollister@gmail.com> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk> Cc: Tristram Ha <Tristram.Ha@microchip.com> Cc: Woojung Huh <woojung.huh@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>

Add initial support for the KSZ8795 Ethernet switch on the RevPi Flat. Signed-off-by: Lukas Wunner <lukas@wunner.de>

The following sequence of operations results in a refcount warning: 1. Open device /dev/tpmrm. 2. Remove module tpm_tis_spi. 3. Write a TPM command to the file descriptor opened at step 1. ------------[ cut here ]------------ WARNING: CPU: 3 PID: 1161 at lib/refcount.c:25 kobject_get+0xa0/0xa4 refcount_t: addition on 0; use-after-free. Modules linked in: tpm_tis_spi tpm_tis_core tpm mdio_bcm_unimac brcmfmac sha256_generic libsha256 sha256_arm hci_uart btbcm bluetooth cfg80211 vc4 brcmutil ecdh_generic ecc snd_soc_core crc32_arm_ce libaes raspberrypi_hwmon ac97_bus snd_pcm_dmaengine bcm2711_thermal snd_pcm snd_timer genet snd phy_generic soundcore [last unloaded: spi_bcm2835] CPU: 3 PID: 1161 Comm: hold_open Not tainted 5.10.0ls-main-dirty RevolutionPi#2 Hardware name: BCM2711 [<c0410c3c>] (unwind_backtrace) from [<c040b580>] (show_stack+0x10/0x14) [<c040b580>] (show_stack) from [<c1092174>] (dump_stack+0xc4/0xd8) [<c1092174>] (dump_stack) from [<c0445a30>] (__warn+0x104/0x108) [<c0445a30>] (__warn) from [<c0445aa8>] (warn_slowpath_fmt+0x74/0xb8) [<c0445aa8>] (warn_slowpath_fmt) from [<c08435d0>] (kobject_get+0xa0/0xa4) [<c08435d0>] (kobject_get) from [<bf0a715c>] (tpm_try_get_ops+0x14/0x54 [tpm]) [<bf0a715c>] (tpm_try_get_ops [tpm]) from [<bf0a7d6c>] (tpm_common_write+0x38/0x60 [tpm]) [<bf0a7d6c>] (tpm_common_write [tpm]) from [<c05a7ac0>] (vfs_write+0xc4/0x3c0) [<c05a7ac0>] (vfs_write) from [<c05a7ee4>] (ksys_write+0x58/0xcc) [<c05a7ee4>] (ksys_write) from [<c04001a0>] (ret_fast_syscall+0x0/0x4c) Exception stack(0xc226bfa8 to 0xc226bff0) bfa0: 00000000 000105b4 00000003 beafe664 00000014 00000000 bfc0: 00000000 000105b4 000103f8 00000004 00000000 00000000 b6f9c000 beafe684 bfe0: 0000006c beafe648 0001056c b6eb6944 ---[ end trace d4b8409def9b8b1f ]--- The reason for this warning is the attempt to get the chip->dev reference in tpm_common_write() although the reference counter is already zero. Since commit 8979b02 ("tpm: Fix reference count to main device") the extra reference used to prevent a premature zero counter is never taken, because the required TPM_CHIP_FLAG_TPM2 flag is never set. Fix this by moving the TPM 2 character device handling from tpm_chip_alloc() to tpm_add_char_device() which is called at a later point in time when the flag has been set in case of TPM2. Commit fdc915f ("tpm: expose spaces via a device link /dev/tpmrm<n>") already introduced function tpm_devs_release() to release the extra reference but did not implement the required put on chip->devs that results in the call of this function. Fix this by putting chip->devs in tpm_chip_unregister(). Finally move the new implementation for the TPM 2 handling into a new function to avoid multiple checks for the TPM_CHIP_FLAG_TPM2 flag in the good case and error cases. Note: The integration of this patch into mainline is still pending! Cc: stable@vger.kernel.org Fixes: fdc915f ("tpm: expose spaces via a device link /dev/tpmrm<n>") Fixes: 8979b02 ("tpm: Fix reference count to main device") Co-developed-by: Jason Gunthorpe <jgg@ziepe.ca> Signed-off-by: Jason Gunthorpe <jgg@ziepe.ca> Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>

The following sequence of operations results in a refcount warning: 1. Open device /dev/tpmrm. 2. Remove module tpm_tis_spi. 3. Write a TPM command to the file descriptor opened at step 1. ------------[ cut here ]------------ WARNING: CPU: 3 PID: 1161 at lib/refcount.c:25 kobject_get+0xa0/0xa4 refcount_t: addition on 0; use-after-free. Modules linked in: tpm_tis_spi tpm_tis_core tpm mdio_bcm_unimac brcmfmac sha256_generic libsha256 sha256_arm hci_uart btbcm bluetooth cfg80211 vc4 brcmutil ecdh_generic ecc snd_soc_core crc32_arm_ce libaes raspberrypi_hwmon ac97_bus snd_pcm_dmaengine bcm2711_thermal snd_pcm snd_timer genet snd phy_generic soundcore [last unloaded: spi_bcm2835] CPU: 3 PID: 1161 Comm: hold_open Not tainted 5.10.0ls-main-dirty #2 Hardware name: BCM2711 [<c0410c3c>] (unwind_backtrace) from [<c040b580>] (show_stack+0x10/0x14) [<c040b580>] (show_stack) from [<c1092174>] (dump_stack+0xc4/0xd8) [<c1092174>] (dump_stack) from [<c0445a30>] (__warn+0x104/0x108) [<c0445a30>] (__warn) from [<c0445aa8>] (warn_slowpath_fmt+0x74/0xb8) [<c0445aa8>] (warn_slowpath_fmt) from [<c08435d0>] (kobject_get+0xa0/0xa4) [<c08435d0>] (kobject_get) from [<bf0a715c>] (tpm_try_get_ops+0x14/0x54 [tpm]) [<bf0a715c>] (tpm_try_get_ops [tpm]) from [<bf0a7d6c>] (tpm_common_write+0x38/0x60 [tpm]) [<bf0a7d6c>] (tpm_common_write [tpm]) from [<c05a7ac0>] (vfs_write+0xc4/0x3c0) [<c05a7ac0>] (vfs_write) from [<c05a7ee4>] (ksys_write+0x58/0xcc) [<c05a7ee4>] (ksys_write) from [<c04001a0>] (ret_fast_syscall+0x0/0x4c) Exception stack(0xc226bfa8 to 0xc226bff0) bfa0: 00000000 000105b4 00000003 beafe664 00000014 00000000 bfc0: 00000000 000105b4 000103f8 00000004 00000000 00000000 b6f9c000 beafe684 bfe0: 0000006c beafe648 0001056c b6eb6944 ---[ end trace d4b8409def9b8b1f ]--- The reason for this warning is the attempt to get the chip->dev reference in tpm_common_write() although the reference counter is already zero. Since commit 8979b02 ("tpm: Fix reference count to main device") the extra reference used to prevent a premature zero counter is never taken, because the required TPM_CHIP_FLAG_TPM2 flag is never set. Fix this by moving the TPM 2 character device handling from tpm_chip_alloc() to tpm_add_char_device() which is called at a later point in time when the flag has been set in case of TPM2. Commit fdc915f ("tpm: expose spaces via a device link /dev/tpmrm<n>") already introduced function tpm_devs_release() to release the extra reference but did not implement the required put on chip->devs that results in the call of this function. Fix this by putting chip->devs in tpm_chip_unregister(). Finally move the new implementation for the TPM 2 handling into a new function to avoid multiple checks for the TPM_CHIP_FLAG_TPM2 flag in the good case and error cases. Note: The integration of this patch into mainline is still pending! Cc: stable@vger.kernel.org Fixes: fdc915f ("tpm: expose spaces via a device link /dev/tpmrm<n>") Fixes: 8979b02 ("tpm: Fix reference count to main device") Co-developed-by: Jason Gunthorpe <jgg@ziepe.ca> Signed-off-by: Jason Gunthorpe <jgg@ziepe.ca> Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>

[ Upstream commit 8ef9dc0 ] We got the following lockdep splat while running fstests (specifically btrfs/003 and btrfs/020 in a row) with the new rc. This was uncovered by 87579e9 ("loop: use worker per cgroup instead of kworker") which converted loop to using workqueues, which comes with lockdep annotations that don't exist with kworkers. The lockdep splat is as follows: WARNING: possible circular locking dependency detected 5.14.0-rc2-custom+ #34 Not tainted ------------------------------------------------------ losetup/156417 is trying to acquire lock: ffff9c7645b02d38 ((wq_completion)loop0){+.+.}-{0:0}, at: flush_workqueue+0x84/0x600 but task is already holding lock: ffff9c7647395468 (&lo->lo_mutex){+.+.}-{3:3}, at: __loop_clr_fd+0x41/0x650 [loop] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #5 (&lo->lo_mutex){+.+.}-{3:3}: __mutex_lock+0xba/0x7c0 lo_open+0x28/0x60 [loop] blkdev_get_whole+0x28/0xf0 blkdev_get_by_dev.part.0+0x168/0x3c0 blkdev_open+0xd2/0xe0 do_dentry_open+0x163/0x3a0 path_openat+0x74d/0xa40 do_filp_open+0x9c/0x140 do_sys_openat2+0xb1/0x170 __x64_sys_openat+0x54/0x90 do_syscall_64+0x3b/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae -> #4 (&disk->open_mutex){+.+.}-{3:3}: __mutex_lock+0xba/0x7c0 blkdev_get_by_dev.part.0+0xd1/0x3c0 blkdev_get_by_path+0xc0/0xd0 btrfs_scan_one_device+0x52/0x1f0 [btrfs] btrfs_control_ioctl+0xac/0x170 [btrfs] __x64_sys_ioctl+0x83/0xb0 do_syscall_64+0x3b/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae -> #3 (uuid_mutex){+.+.}-{3:3}: __mutex_lock+0xba/0x7c0 btrfs_rm_device+0x48/0x6a0 [btrfs] btrfs_ioctl+0x2d1c/0x3110 [btrfs] __x64_sys_ioctl+0x83/0xb0 do_syscall_64+0x3b/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae -> #2 (sb_writers#11){.+.+}-{0:0}: lo_write_bvec+0x112/0x290 [loop] loop_process_work+0x25f/0xcb0 [loop] process_one_work+0x28f/0x5d0 worker_thread+0x55/0x3c0 kthread+0x140/0x170 ret_from_fork+0x22/0x30 -> #1 ((work_completion)(&lo->rootcg_work)){+.+.}-{0:0}: process_one_work+0x266/0x5d0 worker_thread+0x55/0x3c0 kthread+0x140/0x170 ret_from_fork+0x22/0x30 -> #0 ((wq_completion)loop0){+.+.}-{0:0}: __lock_acquire+0x1130/0x1dc0 lock_acquire+0xf5/0x320 flush_workqueue+0xae/0x600 drain_workqueue+0xa0/0x110 destroy_workqueue+0x36/0x250 __loop_clr_fd+0x9a/0x650 [loop] lo_ioctl+0x29d/0x780 [loop] block_ioctl+0x3f/0x50 __x64_sys_ioctl+0x83/0xb0 do_syscall_64+0x3b/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae other info that might help us debug this: Chain exists of: (wq_completion)loop0 --> &disk->open_mutex --> &lo->lo_mutex Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&lo->lo_mutex); lock(&disk->open_mutex); lock(&lo->lo_mutex); lock((wq_completion)loop0); *** DEADLOCK *** 1 lock held by losetup/156417: #0: ffff9c7647395468 (&lo->lo_mutex){+.+.}-{3:3}, at: __loop_clr_fd+0x41/0x650 [loop] stack backtrace: CPU: 8 PID: 156417 Comm: losetup Not tainted 5.14.0-rc2-custom+ #34 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015 Call Trace: dump_stack_lvl+0x57/0x72 check_noncircular+0x10a/0x120 __lock_acquire+0x1130/0x1dc0 lock_acquire+0xf5/0x320 ? flush_workqueue+0x84/0x600 flush_workqueue+0xae/0x600 ? flush_workqueue+0x84/0x600 drain_workqueue+0xa0/0x110 destroy_workqueue+0x36/0x250 __loop_clr_fd+0x9a/0x650 [loop] lo_ioctl+0x29d/0x780 [loop] ? __lock_acquire+0x3a0/0x1dc0 ? update_dl_rq_load_avg+0x152/0x360 ? lock_is_held_type+0xa5/0x120 ? find_held_lock.constprop.0+0x2b/0x80 block_ioctl+0x3f/0x50 __x64_sys_ioctl+0x83/0xb0 do_syscall_64+0x3b/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f645884de6b Usually the uuid_mutex exists to protect the fs_devices that map together all of the devices that match a specific uuid. In rm_device we're messing with the uuid of a device, so it makes sense to protect that here. However in doing that it pulls in a whole host of lockdep dependencies, as we call mnt_may_write() on the sb before we grab the uuid_mutex, thus we end up with the dependency chain under the uuid_mutex being added under the normal sb write dependency chain, which causes problems with loop devices. We don't need the uuid mutex here however. If we call btrfs_scan_one_device() before we scratch the super block we will find the fs_devices and not find the device itself and return EBUSY because the fs_devices is open. If we call it after the scratch happens it will not appear to be a valid btrfs file system. We do not need to worry about other fs_devices modifying operations here because we're protected by the exclusive operations locking. So drop the uuid_mutex here in order to fix the lockdep splat. A more detailed explanation from the discussion: We are worried about rm and scan racing with each other, before this change we'll zero the device out under the UUID mutex so when scan does run it'll make sure that it can go through the whole device scan thing without rm messing with us. We aren't worried if the scratch happens first, because the result is we don't think this is a btrfs device and we bail out. The only case we are concerned with is we scratch _after_ scan is able to read the superblock and gets a seemingly valid super block, so lets consider this case. Scan will call device_list_add() with the device we're removing. We'll call find_fsid_with_metadata_uuid() and get our fs_devices for this UUID. At this point we lock the fs_devices->device_list_mutex. This is what protects us in this case, but we have two cases here. 1. We aren't to the device removal part of the RM. We found our device, and device name matches our path, we go down and we set total_devices to our super number of devices, which doesn't affect anything because we haven't done the remove yet. 2. We are past the device removal part, which is protected by the device_list_mutex. Scan doesn't find the device, it goes down and does the if (fs_devices->opened) return -EBUSY; check and we bail out. Nothing about this situation is ideal, but the lockdep splat is real, and the fix is safe, tho admittedly a bit scary looking. Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> [ copy more from the discussion ] Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

…eam state [ Upstream commit b7b1d02 ] The internal stream state sets the timeout to 120 seconds 2 seconds after the creation of the flow, attach this internal stream state to the IPS_ASSURED flag for consistent event reporting. Before this patch: [NEW] udp 17 30 src=10.246.11.13 dst=216.239.35.0 sport=37282 dport=123 [UNREPLIED] src=216.239.35.0 dst=10.246.11.13 sport=123 dport=37282 [UPDATE] udp 17 30 src=10.246.11.13 dst=216.239.35.0 sport=37282 dport=123 src=216.239.35.0 dst=10.246.11.13 sport=123 dport=37282 [UPDATE] udp 17 30 src=10.246.11.13 dst=216.239.35.0 sport=37282 dport=123 src=216.239.35.0 dst=10.246.11.13 sport=123 dport=37282 [ASSURED] [DESTROY] udp 17 src=10.246.11.13 dst=216.239.35.0 sport=37282 dport=123 src=216.239.35.0 dst=10.246.11.13 sport=123 dport=37282 [ASSURED] Note IPS_ASSURED for the flow not yet in the internal stream state. after this update: [NEW] udp 17 30 src=10.246.11.13 dst=216.239.35.0 sport=37282 dport=123 [UNREPLIED] src=216.239.35.0 dst=10.246.11.13 sport=123 dport=37282 [UPDATE] udp 17 30 src=10.246.11.13 dst=216.239.35.0 sport=37282 dport=123 src=216.239.35.0 dst=10.246.11.13 sport=123 dport=37282 [UPDATE] udp 17 120 src=10.246.11.13 dst=216.239.35.0 sport=37282 dport=123 src=216.239.35.0 dst=10.246.11.13 sport=123 dport=37282 [ASSURED] [DESTROY] udp 17 src=10.246.11.13 dst=216.239.35.0 sport=37282 dport=123 src=216.239.35.0 dst=10.246.11.13 sport=123 dport=37282 [ASSURED] Before this patch, short-lived UDP flows never entered IPS_ASSURED, so they were already candidate flow to be deleted by early_drop under stress. Before this patch, IPS_ASSURED is set on regardless the internal stream state, attach this internal stream state to IPS_ASSURED. packet #1 (original direction) enters NEW state packet #2 (reply direction) enters ESTABLISHED state, sets on IPS_SEEN_REPLY paclet #3 (any direction) sets on IPS_ASSURED (if 2 seconds since the creation has passed by). Reported-by: Maciej Żenczykowski <zenczykowski@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 54659ca ] when turning off a connection, lockdep complains with the following warning (a modprobe has been done but the same happens with a disconnection from NetworkManager, it's enough to trigger a cfg80211_disconnect call): [ 682.855867] ====================================================== [ 682.855877] WARNING: possible circular locking dependency detected [ 682.855887] 5.14.0-rc6+ #16 Tainted: G C OE [ 682.855898] ------------------------------------------------------ [ 682.855906] modprobe/1770 is trying to acquire lock: [ 682.855916] ffffb6d000332b00 (&pxmitpriv->lock){+.-.}-{2:2}, at: rtw_free_stainfo+0x52/0x4a0 [r8723bs] [ 682.856073] but task is already holding lock: [ 682.856081] ffffb6d0003336a8 (&pstapriv->sta_hash_lock){+.-.}-{2:2}, at: rtw_free_assoc_resources+0x48/0x110 [r8723bs] [ 682.856207] which lock already depends on the new lock. [ 682.856215] the existing dependency chain (in reverse order) is: [ 682.856223] -> #1 (&pstapriv->sta_hash_lock){+.-.}-{2:2}: [ 682.856247] _raw_spin_lock_bh+0x34/0x40 [ 682.856265] rtw_get_stainfo+0x9a/0x110 [r8723bs] [ 682.856389] rtw_xmit_classifier+0x27/0x130 [r8723bs] [ 682.856515] rtw_xmitframe_enqueue+0xa/0x20 [r8723bs] [ 682.856642] rtl8723bs_hal_xmit+0x3b/0xb0 [r8723bs] [ 682.856752] rtw_xmit+0x4ef/0x890 [r8723bs] [ 682.856879] _rtw_xmit_entry+0xba/0x350 [r8723bs] [ 682.856981] dev_hard_start_xmit+0xee/0x320 [ 682.856999] sch_direct_xmit+0x8c/0x330 [ 682.857014] __dev_queue_xmit+0xba5/0xf00 [ 682.857030] packet_sendmsg+0x981/0x1b80 [ 682.857047] sock_sendmsg+0x5b/0x60 [ 682.857060] __sys_sendto+0xf1/0x160 [ 682.857073] __x64_sys_sendto+0x24/0x30 [ 682.857087] do_syscall_64+0x3a/0x80 [ 682.857102] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 682.857117] -> #0 (&pxmitpriv->lock){+.-.}-{2:2}: [ 682.857142] __lock_acquire+0xfd9/0x1b50 [ 682.857158] lock_acquire+0xb4/0x2c0 [ 682.857172] _raw_spin_lock_bh+0x34/0x40 [ 682.857185] rtw_free_stainfo+0x52/0x4a0 [r8723bs] [ 682.857308] rtw_free_assoc_resources+0x53/0x110 [r8723bs] [ 682.857415] cfg80211_rtw_disconnect+0x4b/0x70 [r8723bs] [ 682.857522] cfg80211_disconnect+0x12e/0x2f0 [cfg80211] [ 682.857759] cfg80211_leave+0x2b/0x40 [cfg80211] [ 682.857961] cfg80211_netdev_notifier_call+0xa9/0x560 [cfg80211] [ 682.858163] raw_notifier_call_chain+0x41/0x50 [ 682.858180] __dev_close_many+0x62/0x100 [ 682.858195] dev_close_many+0x7d/0x120 [ 682.858209] unregister_netdevice_many+0x416/0x680 [ 682.858225] unregister_netdevice_queue+0xab/0xf0 [ 682.858240] unregister_netdev+0x18/0x20 [ 682.858255] rtw_unregister_netdevs+0x28/0x40 [r8723bs] [ 682.858360] rtw_dev_remove+0x24/0xd0 [r8723bs] [ 682.858463] sdio_bus_remove+0x31/0xd0 [mmc_core] [ 682.858532] device_release_driver_internal+0xf7/0x1d0 [ 682.858550] driver_detach+0x47/0x90 [ 682.858564] bus_remove_driver+0x77/0xd0 [ 682.858579] rtw_drv_halt+0xc/0x678 [r8723bs] [ 682.858685] __x64_sys_delete_module+0x13f/0x250 [ 682.858699] do_syscall_64+0x3a/0x80 [ 682.858715] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 682.858729] other info that might help us debug this: [ 682.858737] Possible unsafe locking scenario: [ 682.858744] CPU0 CPU1 [ 682.858751] ---- ---- [ 682.858758] lock(&pstapriv->sta_hash_lock); [ 682.858772] lock(&pxmitpriv->lock); [ 682.858786] lock(&pstapriv->sta_hash_lock); [ 682.858799] lock(&pxmitpriv->lock); [ 682.858812] *** DEADLOCK *** [ 682.858820] 5 locks held by modprobe/1770: [ 682.858831] #0: ffff8d870697d980 (&dev->mutex){....}-{3:3}, at: device_release_driver_internal+0x1a/0x1d0 [ 682.858869] #1: ffffffffbdbbf1c8 (rtnl_mutex){+.+.}-{3:3}, at: unregister_netdev+0xe/0x20 [ 682.858906] #2: ffff8d87054ee5e8 (&rdev->wiphy.mtx){+.+.}-{3:3}, at: cfg80211_netdev_notifier_call+0x9e/0x560 [cfg80211] [ 682.859131] #3: ffff8d870f2bc8f0 (&wdev->mtx){+.+.}-{3:3}, at: cfg80211_leave+0x20/0x40 [cfg80211] [ 682.859354] #4: ffffb6d0003336a8 (&pstapriv->sta_hash_lock){+.-.}-{2:2}, at: rtw_free_assoc_resources+0x48/0x110 [r8723bs] [ 682.859482] stack backtrace: [ 682.859491] CPU: 1 PID: 1770 Comm: modprobe Tainted: G C OE 5.14.0-rc6+ #16 [ 682.859507] Hardware name: LENOVO 80NR/Madrid, BIOS DACN25WW 08/20/2015 [ 682.859517] Call Trace: [ 682.859531] dump_stack_lvl+0x56/0x6f [ 682.859551] check_noncircular+0xdb/0xf0 [ 682.859579] __lock_acquire+0xfd9/0x1b50 [ 682.859606] lock_acquire+0xb4/0x2c0 [ 682.859623] ? rtw_free_stainfo+0x52/0x4a0 [r8723bs] [ 682.859752] ? mark_held_locks+0x48/0x70 [ 682.859769] ? rtw_free_stainfo+0x4a/0x4a0 [r8723bs] [ 682.859898] _raw_spin_lock_bh+0x34/0x40 [ 682.859914] ? rtw_free_stainfo+0x52/0x4a0 [r8723bs] [ 682.860039] rtw_free_stainfo+0x52/0x4a0 [r8723bs] [ 682.860171] rtw_free_assoc_resources+0x53/0x110 [r8723bs] [ 682.860286] cfg80211_rtw_disconnect+0x4b/0x70 [r8723bs] [ 682.860397] cfg80211_disconnect+0x12e/0x2f0 [cfg80211] [ 682.860629] cfg80211_leave+0x2b/0x40 [cfg80211] [ 682.860836] cfg80211_netdev_notifier_call+0xa9/0x560 [cfg80211] [ 682.861048] ? __lock_acquire+0x4dc/0x1b50 [ 682.861070] ? lock_is_held_type+0xa8/0x110 [ 682.861089] ? lock_is_held_type+0xa8/0x110 [ 682.861104] ? find_held_lock+0x2d/0x90 [ 682.861120] ? packet_notifier+0x173/0x300 [ 682.861141] ? lock_release+0xb3/0x250 [ 682.861160] ? packet_notifier+0x192/0x300 [ 682.861184] raw_notifier_call_chain+0x41/0x50 [ 682.861205] __dev_close_many+0x62/0x100 [ 682.861224] dev_close_many+0x7d/0x120 [ 682.861245] unregister_netdevice_many+0x416/0x680 [ 682.861264] ? find_held_lock+0x2d/0x90 [ 682.861284] unregister_netdevice_queue+0xab/0xf0 [ 682.861306] unregister_netdev+0x18/0x20 [ 682.861325] rtw_unregister_netdevs+0x28/0x40 [r8723bs] [ 682.861434] rtw_dev_remove+0x24/0xd0 [r8723bs] [ 682.861542] sdio_bus_remove+0x31/0xd0 [mmc_core] [ 682.861615] device_release_driver_internal+0xf7/0x1d0 [ 682.861637] driver_detach+0x47/0x90 [ 682.861656] bus_remove_driver+0x77/0xd0 [ 682.861674] rtw_drv_halt+0xc/0x678 [r8723bs] [ 682.861782] __x64_sys_delete_module+0x13f/0x250 [ 682.861801] ? lockdep_hardirqs_on_prepare+0xf3/0x170 [ 682.861817] ? syscall_enter_from_user_mode+0x20/0x70 [ 682.861836] do_syscall_64+0x3a/0x80 [ 682.861855] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 682.861873] RIP: 0033:0x7f6dbe85400b [ 682.861890] Code: 73 01 c3 48 8b 0d 6d 1e 0c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa b8 b0 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 3d 1e 0c 00 f7 d8 64 89 01 48 [ 682.861906] RSP: 002b:00007ffe7a82f538 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0 [ 682.861923] RAX: ffffffffffffffda RBX: 000055a64693bd20 RCX: 00007f6dbe85400b [ 682.861935] RDX: 0000000000000000 RSI: 0000000000000800 RDI: 000055a64693bd88 [ 682.861946] RBP: 000055a64693bd20 R08: 0000000000000000 R09: 0000000000000000 [ 682.861957] R10: 00007f6dbe8c7ac0 R11: 0000000000000206 R12: 000055a64693bd88 [ 682.861967] R13: 0000000000000000 R14: 000055a64693bd88 R15: 00007ffe7a831848 This happens because when we enqueue a frame for transmission we do it under xmit_priv lock, then calling rtw_get_stainfo (needed for enqueuing) takes sta_hash_lock and this leads to the following lock dependency: xmit_priv->lock -> sta_hash_lock Turning off a connection will bring to call rtw_free_assoc_resources which will set up the inverse dependency: sta_hash_lock -> xmit_priv_lock This could lead to a deadlock as lockdep complains. Fix it by removing the xmit_priv->lock around rtw_xmitframe_enqueue call inside rtl8723bs_hal_xmit and put it in a smaller critical section inside rtw_xmit_classifier, the only place where xmit_priv data are actually accessed. Replace spin_{lock,unlock}_bh(pxmitpriv->lock) in other tx paths leading to rtw_xmitframe_enqueue call with spin_{lock,unlock}_bh(psta->sleep_q.lock) - it's not clear why accessing a sleep_q was protected by a spinlock on xmitpriv->lock. This way is avoided the same faulty lock nesting order. Extra changes in v2 by Hans de Goede: -Lift the taking of the struct __queue.lock spinlock out of rtw_free_xmitframe_queue() into the callers this allows also protecting a bunch of related state in rtw_free_stainfo(): -Protect psta->sleepq_len on rtw_free_xmitframe_queue(&psta->sleep_q); -Protect struct tx_servq.tx_pending and tx_servq.qcnt when calling rtw_free_xmitframe_queue(&tx_servq.sta_pending) -This also allows moving the spin_lock_bh(&pxmitpriv->lock); to below the sleep_q free-ing code, avoiding another ABBA locking issue CC: Larry Finger <Larry.Finger@lwfinger.net> Co-developed-by: Hans de Goede <hdegoede@redhat.com> Tested-on: Lenovo Ideapad MiiX 300-10IBY Signed-off-by: Fabio Aiuto <fabioaiuto83@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20210920145502.155454-1-hdegoede@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit f347c26 ] The following issue was observed running syzkaller: BUG: KASAN: slab-out-of-bounds in memcpy include/linux/string.h:377 [inline] BUG: KASAN: slab-out-of-bounds in sg_copy_buffer+0x150/0x1c0 lib/scatterlist.c:831 Read of size 2132 at addr ffff8880aea95dc8 by task syz-executor.0/9815 CPU: 0 PID: 9815 Comm: syz-executor.0 Not tainted 4.19.202-00874-gfc0fe04215a9 #2 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xe4/0x14a lib/dump_stack.c:118 print_address_description+0x73/0x280 mm/kasan/report.c:253 kasan_report_error mm/kasan/report.c:352 [inline] kasan_report+0x272/0x370 mm/kasan/report.c:410 memcpy+0x1f/0x50 mm/kasan/kasan.c:302 memcpy include/linux/string.h:377 [inline] sg_copy_buffer+0x150/0x1c0 lib/scatterlist.c:831 fill_from_dev_buffer+0x14f/0x340 drivers/scsi/scsi_debug.c:1021 resp_report_tgtpgs+0x5aa/0x770 drivers/scsi/scsi_debug.c:1772 schedule_resp+0x464/0x12f0 drivers/scsi/scsi_debug.c:4429 scsi_debug_queuecommand+0x467/0x1390 drivers/scsi/scsi_debug.c:5835 scsi_dispatch_cmd+0x3fc/0x9b0 drivers/scsi/scsi_lib.c:1896 scsi_request_fn+0x1042/0x1810 drivers/scsi/scsi_lib.c:2034 __blk_run_queue_uncond block/blk-core.c:464 [inline] __blk_run_queue+0x1a4/0x380 block/blk-core.c:484 blk_execute_rq_nowait+0x1c2/0x2d0 block/blk-exec.c:78 sg_common_write.isra.19+0xd74/0x1dc0 drivers/scsi/sg.c:847 sg_write.part.23+0x6e0/0xd00 drivers/scsi/sg.c:716 sg_write+0x64/0xa0 drivers/scsi/sg.c:622 __vfs_write+0xed/0x690 fs/read_write.c:485 kill_bdev:block_device:00000000e138492c vfs_write+0x184/0x4c0 fs/read_write.c:549 ksys_write+0x107/0x240 fs/read_write.c:599 do_syscall_64+0xc2/0x560 arch/x86/entry/common.c:293 entry_SYSCALL_64_after_hwframe+0x49/0xbe We get 'alen' from command its type is int. If userspace passes a large length we will get a negative 'alen'. Switch n, alen, and rlen to u32. Link: https://lore.kernel.org/r/20211013033913.2551004-3-yebin10@huawei.com Acked-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Ye Bin <yebin10@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit c56c963 upstream. In line 800 (#1), nfp_cpp_area_alloc() allocates and initializes a CPP area structure. But in line 807 (#2), when the cache is allocated failed, this CPP area structure is not freed, which will result in memory leak. We can fix it by freeing the CPP area when the cache is allocated failed (#2). 792 int nfp_cpp_area_cache_add(struct nfp_cpp *cpp, size_t size) 793 { 794 struct nfp_cpp_area_cache *cache; 795 struct nfp_cpp_area *area; 800 area = nfp_cpp_area_alloc(cpp, NFP_CPP_ID(7, NFP_CPP_ACTION_RW, 0), 801 0, size); // #1: allocates and initializes 802 if (!area) 803 return -ENOMEM; 805 cache = kzalloc(sizeof(*cache), GFP_KERNEL); 806 if (!cache) 807 return -ENOMEM; // #2: missing free 817 return 0; 818 } Fixes: 4cb584e ("nfp: add CPP access core") Signed-off-by: Jianglei Nie <niejianglei2021@163.com> Acked-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20211209061511.122535-1-niejianglei2021@163.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f35838a upstream. Line 1169 (#3) allocates a memory chunk for victim_name by kmalloc(), but when the function returns in line 1184 (#4) victim_name allocated by line 1169 (#3) is not freed, which will lead to a memory leak. There is a similar snippet of code in this function as allocating a memory chunk for victim_name in line 1104 (#1) as well as releasing the memory in line 1116 (#2). We should kfree() victim_name when the return value of backref_in_log() is less than zero and before the function returns in line 1184 (#4). 1057 static inline int __add_inode_ref(struct btrfs_trans_handle *trans, 1058 struct btrfs_root *root, 1059 struct btrfs_path *path, 1060 struct btrfs_root *log_root, 1061 struct btrfs_inode *dir, 1062 struct btrfs_inode *inode, 1063 u64 inode_objectid, u64 parent_objectid, 1064 u64 ref_index, char *name, int namelen, 1065 int *search_done) 1066 { 1104 victim_name = kmalloc(victim_name_len, GFP_NOFS); // #1: kmalloc (victim_name-1) 1105 if (!victim_name) 1106 return -ENOMEM; 1112 ret = backref_in_log(log_root, &search_key, 1113 parent_objectid, victim_name, 1114 victim_name_len); 1115 if (ret < 0) { 1116 kfree(victim_name); // #2: kfree (victim_name-1) 1117 return ret; 1118 } else if (!ret) { 1169 victim_name = kmalloc(victim_name_len, GFP_NOFS); // #3: kmalloc (victim_name-2) 1170 if (!victim_name) 1171 return -ENOMEM; 1180 ret = backref_in_log(log_root, &search_key, 1181 parent_objectid, victim_name, 1182 victim_name_len); 1183 if (ret < 0) { 1184 return ret; // #4: missing kfree (victim_name-2) 1185 } else if (!ret) { 1241 return 0; 1242 } Fixes: d3316c8 ("btrfs: Properly handle backref_in_log retval") CC: stable@vger.kernel.org # 5.10+ Reviewed-by: Qu Wenruo <wqu@suse.com> Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Jianglei Nie <niejianglei2021@163.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nbuchwitz · 2022-01-26T21:28:32Z

@l1k is this still relevant or can we close the PR?

iluminat23 · 2022-01-27T07:44:46Z

This would need a H/W change for Flat. And I guess the patch a231a33 is already included in the 5.10 tree from upstream. From my side we can drop the pull-request.

l1k · 2022-01-27T08:33:04Z

This was created as part of REVPI-730 and is still relevant. We're missing support to access and configure the Ethernet switch on the Flat.
The switch can be attached either via SPI or MDIO. However, the CM3 lacks an MDIO interface, leaving SPI as the only viable option. My recollection is that on revision R00 of the Flat, the switch was intended to be attached via SPI, but the hardware team did not actually connect it to the bus. I believe they thought that it would exceed the maximum number of devices that the RasPi can handle on an SPI bus. (In reality, that number is unlimited.)
On R01, they attached the switch to an I2C bus. The I2C interface sort of looks similar to MDIO but is actually quite different. So the only option that we had was to use bit-banging to simulate an MDIO interface. But it turned out that bit-banging doesn't work reliably due to timing issues.
This pull request implements unreliable switch access via bit-banging. It would have to be rebased on devel/revpi-5.10 and the bit-banging would have to be made more reliable, e.g. by performing it with disabled preemption and interrupts. The question is whether that's worth it. I believe we promised our key customer to retrofit switch access on the Flat.
We should redesign the Flat to use SPI in lieu of MDIO going forward.

nbuchwitz · 2022-02-09T19:55:23Z

@RevolutionPi/kernel I'll close this PR and move the relevant parts to the flats errata page

The following sequence of operations results in a refcount warning: 1. Open device /dev/tpmrm. 2. Remove module tpm_tis_spi. 3. Write a TPM command to the file descriptor opened at step 1. ------------[ cut here ]------------ WARNING: CPU: 3 PID: 1161 at lib/refcount.c:25 kobject_get+0xa0/0xa4 refcount_t: addition on 0; use-after-free. Modules linked in: tpm_tis_spi tpm_tis_core tpm mdio_bcm_unimac brcmfmac sha256_generic libsha256 sha256_arm hci_uart btbcm bluetooth cfg80211 vc4 brcmutil ecdh_generic ecc snd_soc_core crc32_arm_ce libaes raspberrypi_hwmon ac97_bus snd_pcm_dmaengine bcm2711_thermal snd_pcm snd_timer genet snd phy_generic soundcore [last unloaded: spi_bcm2835] CPU: 3 PID: 1161 Comm: hold_open Not tainted 5.10.0ls-main-dirty RevolutionPi#2 Hardware name: BCM2711 [<c0410c3c>] (unwind_backtrace) from [<c040b580>] (show_stack+0x10/0x14) [<c040b580>] (show_stack) from [<c1092174>] (dump_stack+0xc4/0xd8) [<c1092174>] (dump_stack) from [<c0445a30>] (__warn+0x104/0x108) [<c0445a30>] (__warn) from [<c0445aa8>] (warn_slowpath_fmt+0x74/0xb8) [<c0445aa8>] (warn_slowpath_fmt) from [<c08435d0>] (kobject_get+0xa0/0xa4) [<c08435d0>] (kobject_get) from [<bf0a715c>] (tpm_try_get_ops+0x14/0x54 [tpm]) [<bf0a715c>] (tpm_try_get_ops [tpm]) from [<bf0a7d6c>] (tpm_common_write+0x38/0x60 [tpm]) [<bf0a7d6c>] (tpm_common_write [tpm]) from [<c05a7ac0>] (vfs_write+0xc4/0x3c0) [<c05a7ac0>] (vfs_write) from [<c05a7ee4>] (ksys_write+0x58/0xcc) [<c05a7ee4>] (ksys_write) from [<c04001a0>] (ret_fast_syscall+0x0/0x4c) Exception stack(0xc226bfa8 to 0xc226bff0) bfa0: 00000000 000105b4 00000003 beafe664 00000014 00000000 bfc0: 00000000 000105b4 000103f8 00000004 00000000 00000000 b6f9c000 beafe684 bfe0: 0000006c beafe648 0001056c b6eb6944 ---[ end trace d4b8409def9b8b1f ]--- The reason for this warning is the attempt to get the chip->dev reference in tpm_common_write() although the reference counter is already zero. Since commit 8979b02 ("tpm: Fix reference count to main device") the extra reference used to prevent a premature zero counter is never taken, because the required TPM_CHIP_FLAG_TPM2 flag is never set. Fix this by moving the TPM 2 character device handling from tpm_chip_alloc() to tpm_add_char_device() which is called at a later point in time when the flag has been set in case of TPM2. Commit fdc915f ("tpm: expose spaces via a device link /dev/tpmrm<n>") already introduced function tpm_devs_release() to release the extra reference but did not implement the required put on chip->devs that results in the call of this function. Fix this by putting chip->devs in tpm_chip_unregister(). Finally move the new implementation for the TPM 2 handling into a new function to avoid multiple checks for the TPM_CHIP_FLAG_TPM2 flag in the good case and error cases. Note: The integration of this patch into mainline is still pending! Cc: stable@vger.kernel.org Fixes: fdc915f ("tpm: expose spaces via a device link /dev/tpmrm<n>") Fixes: 8979b02 ("tpm: Fix reference count to main device") Co-developed-by: Jason Gunthorpe <jgg@ziepe.ca> Signed-off-by: Jason Gunthorpe <jgg@ziepe.ca> Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>

The following sequence of operations results in a refcount warning: 1. Open device /dev/tpmrm. 2. Remove module tpm_tis_spi. 3. Write a TPM command to the file descriptor opened at step 1. ------------[ cut here ]------------ WARNING: CPU: 3 PID: 1161 at lib/refcount.c:25 kobject_get+0xa0/0xa4 refcount_t: addition on 0; use-after-free. Modules linked in: tpm_tis_spi tpm_tis_core tpm mdio_bcm_unimac brcmfmac sha256_generic libsha256 sha256_arm hci_uart btbcm bluetooth cfg80211 vc4 brcmutil ecdh_generic ecc snd_soc_core crc32_arm_ce libaes raspberrypi_hwmon ac97_bus snd_pcm_dmaengine bcm2711_thermal snd_pcm snd_timer genet snd phy_generic soundcore [last unloaded: spi_bcm2835] CPU: 3 PID: 1161 Comm: hold_open Not tainted 5.10.0ls-main-dirty #2 Hardware name: BCM2711 [<c0410c3c>] (unwind_backtrace) from [<c040b580>] (show_stack+0x10/0x14) [<c040b580>] (show_stack) from [<c1092174>] (dump_stack+0xc4/0xd8) [<c1092174>] (dump_stack) from [<c0445a30>] (__warn+0x104/0x108) [<c0445a30>] (__warn) from [<c0445aa8>] (warn_slowpath_fmt+0x74/0xb8) [<c0445aa8>] (warn_slowpath_fmt) from [<c08435d0>] (kobject_get+0xa0/0xa4) [<c08435d0>] (kobject_get) from [<bf0a715c>] (tpm_try_get_ops+0x14/0x54 [tpm]) [<bf0a715c>] (tpm_try_get_ops [tpm]) from [<bf0a7d6c>] (tpm_common_write+0x38/0x60 [tpm]) [<bf0a7d6c>] (tpm_common_write [tpm]) from [<c05a7ac0>] (vfs_write+0xc4/0x3c0) [<c05a7ac0>] (vfs_write) from [<c05a7ee4>] (ksys_write+0x58/0xcc) [<c05a7ee4>] (ksys_write) from [<c04001a0>] (ret_fast_syscall+0x0/0x4c) Exception stack(0xc226bfa8 to 0xc226bff0) bfa0: 00000000 000105b4 00000003 beafe664 00000014 00000000 bfc0: 00000000 000105b4 000103f8 00000004 00000000 00000000 b6f9c000 beafe684 bfe0: 0000006c beafe648 0001056c b6eb6944 ---[ end trace d4b8409def9b8b1f ]--- The reason for this warning is the attempt to get the chip->dev reference in tpm_common_write() although the reference counter is already zero. Since commit 8979b02 ("tpm: Fix reference count to main device") the extra reference used to prevent a premature zero counter is never taken, because the required TPM_CHIP_FLAG_TPM2 flag is never set. Fix this by moving the TPM 2 character device handling from tpm_chip_alloc() to tpm_add_char_device() which is called at a later point in time when the flag has been set in case of TPM2. Commit fdc915f ("tpm: expose spaces via a device link /dev/tpmrm<n>") already introduced function tpm_devs_release() to release the extra reference but did not implement the required put on chip->devs that results in the call of this function. Fix this by putting chip->devs in tpm_chip_unregister(). Finally move the new implementation for the TPM 2 handling into a new function to avoid multiple checks for the TPM_CHIP_FLAG_TPM2 flag in the good case and error cases. Note: The integration of this patch into mainline is still pending! Cc: stable@vger.kernel.org Fixes: fdc915f ("tpm: expose spaces via a device link /dev/tpmrm<n>") Fixes: 8979b02 ("tpm: Fix reference count to main device") Co-developed-by: Jason Gunthorpe <jgg@ziepe.ca> Signed-off-by: Jason Gunthorpe <jgg@ziepe.ca> Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>

Jakub Sitnicki says: ==================== This patch set addresses the syzbot report in [1]. Patch #1 has been suggested by Eric [2]. I extended it to cover the rest of sock_map proto callbacks. Otherwise we would still overflow the stack. Patch #2 contains the actual fix and bug analysis. Patches #3 & #4 add coverage to selftests to trigger the bug. [1] https://lore.kernel.org/all/00000000000073b14905ef2e7401@google.com/ [2] https://lore.kernel.org/all/CANn89iK2UN1FmdUcH12fv_xiZkv2G+Nskvmq7fG6aA_6VKRf6g@mail.gmail.com/ --- v1 -> v2: v1: https://lore.kernel.org/r/20230113-sockmap-fix-v1-0-d3cad092ee10@cloudflare.com [v1 didn't hit bpf@ ML by mistake] * pull in Eric's patch to protect against recursion loop bugs (Eric) * add a macro helper to check if pointer is inside a memory range (Eric) ==================== Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Some combinations of Pi 4Bs and Ethernet switches don't reliably get a DCHP-assigned IP address, leaving the unit with a self=assigned 169.254 address. In the failure case, the Pi is left able to receive packets but not send them, suggesting that the MAC<->PHY link is getting into a bad state. It has been found empirically that skipping a reset step by the genet driver prevents the failures. No downsides have been discovered yet, and unlike the forced renegotiation it doesn't increase the time to get an IP address, so the workaround is enabled by default; add genet.skip_umac_reset=n to the command line to disable it. See: raspberrypi/linux#3108 Signed-off-by: Phil Elwell <phil@raspberrypi.org>

[ Upstream commit 8d21155 ] adjust_inuse_and_calc_cost() use spin_lock_irq() and IRQ will be enabled when unlock. DEADLOCK might happen if we have held other locks and disabled IRQ before invoking it. Fix it by using spin_lock_irqsave() instead, which can keep IRQ state consistent with before when unlock. ================================ WARNING: inconsistent lock state 5.10.0-02758-g8e5f91fd772f #26 Not tainted -------------------------------- inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage. kworker/2:3/388 [HC0[0]:SC0[0]:HE0:SE1] takes: ffff888118c00c28 (&bfqd->lock){?.-.}-{2:2}, at: spin_lock_irq ffff888118c00c28 (&bfqd->lock){?.-.}-{2:2}, at: bfq_bio_merge+0x141/0x390 {IN-HARDIRQ-W} state was registered at: __lock_acquire+0x3d7/0x1070 lock_acquire+0x197/0x4a0 __raw_spin_lock_irqsave _raw_spin_lock_irqsave+0x3b/0x60 bfq_idle_slice_timer_body bfq_idle_slice_timer+0x53/0x1d0 __run_hrtimer+0x477/0xa70 __hrtimer_run_queues+0x1c6/0x2d0 hrtimer_interrupt+0x302/0x9e0 local_apic_timer_interrupt __sysvec_apic_timer_interrupt+0xfd/0x420 run_sysvec_on_irqstack_cond sysvec_apic_timer_interrupt+0x46/0xa0 asm_sysvec_apic_timer_interrupt+0x12/0x20 irq event stamp: 837522 hardirqs last enabled at (837521): [<ffffffff84b9419d>] __raw_spin_unlock_irqrestore hardirqs last enabled at (837521): [<ffffffff84b9419d>] _raw_spin_unlock_irqrestore+0x3d/0x40 hardirqs last disabled at (837522): [<ffffffff84b93fa3>] __raw_spin_lock_irq hardirqs last disabled at (837522): [<ffffffff84b93fa3>] _raw_spin_lock_irq+0x43/0x50 softirqs last enabled at (835852): [<ffffffff84e00558>] __do_softirq+0x558/0x8ec softirqs last disabled at (835845): [<ffffffff84c010ff>] asm_call_irq_on_stack+0xf/0x20 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&bfqd->lock); <Interrupt> lock(&bfqd->lock); *** DEADLOCK *** 3 locks held by kworker/2:3/388: #0: ffff888107af0f38 ((wq_completion)kthrotld){+.+.}-{0:0}, at: process_one_work+0x742/0x13f0 #1: ffff8881176bfdd8 ((work_completion)(&td->dispatch_work)){+.+.}-{0:0}, at: process_one_work+0x777/0x13f0 #2: ffff888118c00c28 (&bfqd->lock){?.-.}-{2:2}, at: spin_lock_irq #2: ffff888118c00c28 (&bfqd->lock){?.-.}-{2:2}, at: bfq_bio_merge+0x141/0x390 stack backtrace: CPU: 2 PID: 388 Comm: kworker/2:3 Not tainted 5.10.0-02758-g8e5f91fd772f #26 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 Workqueue: kthrotld blk_throtl_dispatch_work_fn Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x107/0x167 print_usage_bug valid_state mark_lock_irq.cold+0x32/0x3a mark_lock+0x693/0xbc0 mark_held_locks+0x9e/0xe0 __trace_hardirqs_on_caller lockdep_hardirqs_on_prepare.part.0+0x151/0x360 trace_hardirqs_on+0x5b/0x180 __raw_spin_unlock_irq _raw_spin_unlock_irq+0x24/0x40 spin_unlock_irq adjust_inuse_and_calc_cost+0x4fb/0x970 ioc_rqos_merge+0x277/0x740 __rq_qos_merge+0x62/0xb0 rq_qos_merge bio_attempt_back_merge+0x12c/0x4a0 blk_mq_sched_try_merge+0x1b6/0x4d0 bfq_bio_merge+0x24a/0x390 __blk_mq_sched_bio_merge+0xa6/0x460 blk_mq_sched_bio_merge blk_mq_submit_bio+0x2e7/0x1ee0 __submit_bio_noacct_mq+0x175/0x3b0 submit_bio_noacct+0x1fb/0x270 blk_throtl_dispatch_work_fn+0x1ef/0x2b0 process_one_work+0x83e/0x13f0 process_scheduled_works worker_thread+0x7e3/0xd80 kthread+0x353/0x470 ret_from_fork+0x1f/0x30 Fixes: b0853ab ("blk-iocost: revamp in-period donation snapbacks") Signed-off-by: Li Nan <linan122@huawei.com> Acked-by: Tejun Heo <tj@kernel.org> Reviewed-by: Yu Kuai <yukuai3@huawei.com> Link: https://lore.kernel.org/r/20230527091904.3001833-1-linan666@huaweicloud.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ce3aee7 ] syzkaller reported use-after-free in __gtp_encap_destroy(). [0] It shows the same process freed sk and touched it illegally. Commit e198987 ("gtp: fix suspicious RCU usage") added lock_sock() and release_sock() in __gtp_encap_destroy() to protect sk->sk_user_data, but release_sock() is called after sock_put() releases the last refcnt. [0]: BUG: KASAN: slab-use-after-free in instrument_atomic_read_write include/linux/instrumented.h:96 [inline] BUG: KASAN: slab-use-after-free in atomic_try_cmpxchg_acquire include/linux/atomic/atomic-instrumented.h:541 [inline] BUG: KASAN: slab-use-after-free in queued_spin_lock include/asm-generic/qspinlock.h:111 [inline] BUG: KASAN: slab-use-after-free in do_raw_spin_lock include/linux/spinlock.h:186 [inline] BUG: KASAN: slab-use-after-free in __raw_spin_lock_bh include/linux/spinlock_api_smp.h:127 [inline] BUG: KASAN: slab-use-after-free in _raw_spin_lock_bh+0x75/0xe0 kernel/locking/spinlock.c:178 Write of size 4 at addr ffff88800dbef398 by task syz-executor.2/2401 CPU: 1 PID: 2401 Comm: syz-executor.2 Not tainted 6.4.0-rc5-01219-gfa0e21fa4443 #2 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x72/0xa0 lib/dump_stack.c:106 print_address_description mm/kasan/report.c:351 [inline] print_report+0xcc/0x620 mm/kasan/report.c:462 kasan_report+0xb2/0xe0 mm/kasan/report.c:572 check_region_inline mm/kasan/generic.c:181 [inline] kasan_check_range+0x39/0x1c0 mm/kasan/generic.c:187 instrument_atomic_read_write include/linux/instrumented.h:96 [inline] atomic_try_cmpxchg_acquire include/linux/atomic/atomic-instrumented.h:541 [inline] queued_spin_lock include/asm-generic/qspinlock.h:111 [inline] do_raw_spin_lock include/linux/spinlock.h:186 [inline] __raw_spin_lock_bh include/linux/spinlock_api_smp.h:127 [inline] _raw_spin_lock_bh+0x75/0xe0 kernel/locking/spinlock.c:178 spin_lock_bh include/linux/spinlock.h:355 [inline] release_sock+0x1f/0x1a0 net/core/sock.c:3526 gtp_encap_disable_sock drivers/net/gtp.c:651 [inline] gtp_encap_disable+0xb9/0x220 drivers/net/gtp.c:664 gtp_dev_uninit+0x19/0x50 drivers/net/gtp.c:728 unregister_netdevice_many_notify+0x97e/0x1520 net/core/dev.c:10841 rtnl_delete_link net/core/rtnetlink.c:3216 [inline] rtnl_dellink+0x3c0/0xb30 net/core/rtnetlink.c:3268 rtnetlink_rcv_msg+0x450/0xb10 net/core/rtnetlink.c:6423 netlink_rcv_skb+0x15d/0x450 net/netlink/af_netlink.c:2548 netlink_unicast_kernel net/netlink/af_netlink.c:1339 [inline] netlink_unicast+0x700/0x930 net/netlink/af_netlink.c:1365 netlink_sendmsg+0x91c/0xe30 net/netlink/af_netlink.c:1913 sock_sendmsg_nosec net/socket.c:724 [inline] sock_sendmsg+0x1b7/0x200 net/socket.c:747 ____sys_sendmsg+0x75a/0x990 net/socket.c:2493 ___sys_sendmsg+0x11d/0x1c0 net/socket.c:2547 __sys_sendmsg+0xfe/0x1d0 net/socket.c:2576 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x3f/0x90 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x72/0xdc RIP: 0033:0x7f1168b1fe5d Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 73 9f 1b 00 f7 d8 64 89 01 48 RSP: 002b:00007f1167edccc8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00000000004bbf80 RCX: 00007f1168b1fe5d RDX: 0000000000000000 RSI: 00000000200002c0 RDI: 0000000000000003 RBP: 00000000004bbf80 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 000000000000000b R14: 00007f1168b80530 R15: 0000000000000000 </TASK> Allocated by task 1483: kasan_save_stack+0x22/0x50 mm/kasan/common.c:45 kasan_set_track+0x25/0x30 mm/kasan/common.c:52 __kasan_slab_alloc+0x59/0x70 mm/kasan/common.c:328 kasan_slab_alloc include/linux/kasan.h:186 [inline] slab_post_alloc_hook mm/slab.h:711 [inline] slab_alloc_node mm/slub.c:3451 [inline] slab_alloc mm/slub.c:3459 [inline] __kmem_cache_alloc_lru mm/slub.c:3466 [inline] kmem_cache_alloc+0x16d/0x340 mm/slub.c:3475 sk_prot_alloc+0x5f/0x280 net/core/sock.c:2073 sk_alloc+0x34/0x6c0 net/core/sock.c:2132 inet6_create net/ipv6/af_inet6.c:192 [inline] inet6_create+0x2c7/0xf20 net/ipv6/af_inet6.c:119 __sock_create+0x2a1/0x530 net/socket.c:1535 sock_create net/socket.c:1586 [inline] __sys_socket_create net/socket.c:1623 [inline] __sys_socket_create net/socket.c:1608 [inline] __sys_socket+0x137/0x250 net/socket.c:1651 __do_sys_socket net/socket.c:1664 [inline] __se_sys_socket net/socket.c:1662 [inline] __x64_sys_socket+0x72/0xb0 net/socket.c:1662 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x3f/0x90 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x72/0xdc Freed by task 2401: kasan_save_stack+0x22/0x50 mm/kasan/common.c:45 kasan_set_track+0x25/0x30 mm/kasan/common.c:52 kasan_save_free_info+0x2e/0x50 mm/kasan/generic.c:521 ____kasan_slab_free mm/kasan/common.c:236 [inline] ____kasan_slab_free mm/kasan/common.c:200 [inline] __kasan_slab_free+0x10c/0x1b0 mm/kasan/common.c:244 kasan_slab_free include/linux/kasan.h:162 [inline] slab_free_hook mm/slub.c:1781 [inline] slab_free_freelist_hook mm/slub.c:1807 [inline] slab_free mm/slub.c:3786 [inline] kmem_cache_free+0xb4/0x490 mm/slub.c:3808 sk_prot_free net/core/sock.c:2113 [inline] __sk_destruct+0x500/0x720 net/core/sock.c:2207 sk_destruct+0xc1/0xe0 net/core/sock.c:2222 __sk_free+0xed/0x3d0 net/core/sock.c:2233 sk_free+0x7c/0xa0 net/core/sock.c:2244 sock_put include/net/sock.h:1981 [inline] __gtp_encap_destroy+0x165/0x1b0 drivers/net/gtp.c:634 gtp_encap_disable_sock drivers/net/gtp.c:651 [inline] gtp_encap_disable+0xb9/0x220 drivers/net/gtp.c:664 gtp_dev_uninit+0x19/0x50 drivers/net/gtp.c:728 unregister_netdevice_many_notify+0x97e/0x1520 net/core/dev.c:10841 rtnl_delete_link net/core/rtnetlink.c:3216 [inline] rtnl_dellink+0x3c0/0xb30 net/core/rtnetlink.c:3268 rtnetlink_rcv_msg+0x450/0xb10 net/core/rtnetlink.c:6423 netlink_rcv_skb+0x15d/0x450 net/netlink/af_netlink.c:2548 netlink_unicast_kernel net/netlink/af_netlink.c:1339 [inline] netlink_unicast+0x700/0x930 net/netlink/af_netlink.c:1365 netlink_sendmsg+0x91c/0xe30 net/netlink/af_netlink.c:1913 sock_sendmsg_nosec net/socket.c:724 [inline] sock_sendmsg+0x1b7/0x200 net/socket.c:747 ____sys_sendmsg+0x75a/0x990 net/socket.c:2493 ___sys_sendmsg+0x11d/0x1c0 net/socket.c:2547 __sys_sendmsg+0xfe/0x1d0 net/socket.c:2576 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x3f/0x90 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x72/0xdc The buggy address belongs to the object at ffff88800dbef300 which belongs to the cache UDPv6 of size 1344 The buggy address is located 152 bytes inside of freed 1344-byte region [ffff88800dbef300, ffff88800dbef840) The buggy address belongs to the physical page: page:00000000d31bfed5 refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff88800dbeed40 pfn:0xdbe8 head:00000000d31bfed5 order:3 entire_mapcount:0 nr_pages_mapped:0 pincount:0 memcg:ffff888008ee0801 flags: 0x100000000010200(slab|head|node=0|zone=1) page_type: 0xffffffff() raw: 0100000000010200 ffff88800c7a3000 dead000000000122 0000000000000000 raw: ffff88800dbeed40 0000000080160015 00000001ffffffff ffff888008ee0801 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff88800dbef280: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff88800dbef300: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb >ffff88800dbef380: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff88800dbef400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88800dbef480: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb Fixes: e198987 ("gtp: fix suspicious RCU usage") Reported-by: syzkaller <syzkaller@googlegroups.com> Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Reviewed-by: Pablo Neira Ayuso <pablo@netfilter.org> Link: https://lore.kernel.org/r/20230622213231.24651-1-kuniyu@amazon.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 6f67fbf ] The `shift` variable which indicates the offset in the string at which to start matching the pattern is initialized to `bm->patlen - 1`, but it is not reset when a new block is retrieved. This means the implemen- tation may start looking at later and later positions in each successive block and miss occurrences of the pattern at the beginning. E.g., consider a HTTP packet held in a non-linear skb, where the HTTP request line occurs in the second block: [... 52 bytes of packet headers ...] GET /bmtest HTTP/1.1\r\nHost: www.example.com\r\n\r\n and the pattern is "GET /bmtest". Once the first block comprising the packet headers has been examined, `shift` will be pointing to somewhere near the end of the block, and so when the second block is examined the request line at the beginning will be missed. Reinitialize the variable for each new block. Fixes: 8082e4e ("[LIB]: Boyer-Moore extension for textsearch infrastructure strike #2") Link: https://bugzilla.netfilter.org/show_bug.cgi?id=1390 Signed-off-by: Jeremy Sowden <jeremy@azazel.net> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 99d4850 ] Found by leak sanitizer: ``` ==1632594==ERROR: LeakSanitizer: detected memory leaks Direct leak of 21 byte(s) in 1 object(s) allocated from: #0 0x7f2953a7077b in __interceptor_strdup ../../../../src/libsanitizer/asan/asan_interceptors.cpp:439 #1 0x556701d6fbbf in perf_env__read_cpuid util/env.c:369 #2 0x556701d70589 in perf_env__cpuid util/env.c:465 #3 0x55670204bba2 in x86__is_amd_cpu arch/x86/util/env.c:14 #4 0x5567020487a2 in arch__post_evsel_config arch/x86/util/evsel.c:83 #5 0x556701d8f78b in evsel__config util/evsel.c:1366 #6 0x556701ef5872 in evlist__config util/record.c:108 #7 0x556701cd6bcd in test__PERF_RECORD tests/perf-record.c:112 #8 0x556701cacd07 in run_test tests/builtin-test.c:236 #9 0x556701cacfac in test_and_print tests/builtin-test.c:265 #10 0x556701cadddb in __cmd_test tests/builtin-test.c:402 #11 0x556701caf2aa in cmd_test tests/builtin-test.c:559 #12 0x556701d3b557 in run_builtin tools/perf/perf.c:323 #13 0x556701d3bac8 in handle_internal_command tools/perf/perf.c:377 #14 0x556701d3be90 in run_argv tools/perf/perf.c:421 #15 0x556701d3c3f8 in main tools/perf/perf.c:537 #16 0x7f2952a46189 in __libc_start_call_main ../sysdeps/nptl/libc_start_call_main.h:58 SUMMARY: AddressSanitizer: 21 byte(s) leaked in 1 allocation(s). ``` Fixes: f7b58cb ("perf mem/c2c: Add load store event mappings for AMD") Signed-off-by: Ian Rogers <irogers@google.com> Acked-by: Ravi Bangoria <ravi.bangoria@amd.com> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ravi Bangoria <ravi.bangoria@amd.com> Link: https://lore.kernel.org/r/20230613235416.1650755-1-irogers@google.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit b684c09 ] ppc_save_regs() skips one stack frame while saving the CPU register states. Instead of saving current R1, it pulls the previous stack frame pointer. When vmcores caused by direct panic call (such as `echo c > /proc/sysrq-trigger`), are debugged with gdb, gdb fails to show the backtrace correctly. On further analysis, it was found that it was because of mismatch between r1 and NIP. GDB uses NIP to get current function symbol and uses corresponding debug info of that function to unwind previous frames, but due to the mismatching r1 and NIP, the unwinding does not work, and it fails to unwind to the 2nd frame and hence does not show the backtrace. GDB backtrace with vmcore of kernel without this patch: --------- (gdb) bt #0 0xc0000000002a53e8 in crash_setup_regs (oldregs=<optimized out>, newregs=0xc000000004f8f8d8) at ./arch/powerpc/include/asm/kexec.h:69 #1 __crash_kexec (regs=<optimized out>) at kernel/kexec_core.c:974 #2 0x0000000000000063 in ?? () #3 0xc000000003579320 in ?? () --------- Further analysis revealed that the mismatch occurred because "ppc_save_regs" was saving the previous stack's SP instead of the current r1. This patch fixes this by storing current r1 in the saved pt_regs. GDB backtrace with vmcore of patched kernel: -------- (gdb) bt #0 0xc0000000002a53e8 in crash_setup_regs (oldregs=0x0, newregs=0xc00000000670b8d8) at ./arch/powerpc/include/asm/kexec.h:69 #1 __crash_kexec (regs=regs@entry=0x0) at kernel/kexec_core.c:974 #2 0xc000000000168918 in panic (fmt=fmt@entry=0xc000000001654a60 "sysrq triggered crash\n") at kernel/panic.c:358 #3 0xc000000000b735f8 in sysrq_handle_crash (key=<optimized out>) at drivers/tty/sysrq.c:155 #4 0xc000000000b742cc in __handle_sysrq (key=key@entry=99, check_mask=check_mask@entry=false) at drivers/tty/sysrq.c:602 #5 0xc000000000b7506c in write_sysrq_trigger (file=<optimized out>, buf=<optimized out>, count=2, ppos=<optimized out>) at drivers/tty/sysrq.c:1163 #6 0xc00000000069a7bc in pde_write (ppos=<optimized out>, count=<optimized out>, buf=<optimized out>, file=<optimized out>, pde=0xc00000000362cb40) at fs/proc/inode.c:340 #7 proc_reg_write (file=<optimized out>, buf=<optimized out>, count=<optimized out>, ppos=<optimized out>) at fs/proc/inode.c:352 #8 0xc0000000005b3bbc in vfs_write (file=file@entry=0xc000000006aa6b00, buf=buf@entry=0x61f498b4f60 <error: Cannot access memory at address 0x61f498b4f60>, count=count@entry=2, pos=pos@entry=0xc00000000670bda0) at fs/read_write.c:582 #9 0xc0000000005b4264 in ksys_write (fd=<optimized out>, buf=0x61f498b4f60 <error: Cannot access memory at address 0x61f498b4f60>, count=2) at fs/read_write.c:637 #10 0xc00000000002ea2c in system_call_exception (regs=0xc00000000670be80, r0=<optimized out>) at arch/powerpc/kernel/syscall.c:171 #11 0xc00000000000c270 in system_call_vectored_common () at arch/powerpc/kernel/interrupt_64.S:192 -------- Nick adds: So this now saves regs as though it was an interrupt taken in the caller, at the instruction after the call to ppc_save_regs, whereas previously the NIP was there, but R1 came from the caller's caller and that mismatch is what causes gdb's dwarf unwinder to go haywire. Signed-off-by: Aditya Gupta <adityag@linux.ibm.com> Fixes: d16a58f ("powerpc: Improve ppc_save_regs()") Reivewed-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230615091047.90433-1-adityag@linux.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 303c9c6 ] Changes in VFIO caused a pseudo-device to be created as child of fsl-mc devices causing a crash [1] when trying to bind a fsl-mc device to VFIO. Fix this by checking the device type when enumerating fsl-mc child devices. [1] Modules linked in: Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP CPU: 6 PID: 1289 Comm: sh Not tainted 6.2.0-rc5-00047-g7c46948a6e9c #2 Hardware name: NXP Layerscape LX2160ARDB (DT) pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : mc_send_command+0x24/0x1f0 lr : dprc_get_obj_region+0xfc/0x1c0 sp : ffff80000a88b900 x29: ffff80000a88b900 x28: ffff48a9429e1400 x27: 00000000000002b2 x26: ffff48a9429e1718 x25: 0000000000000000 x24: 0000000000000000 x23: ffffd59331ba3918 x22: ffffd59331ba3000 x21: 0000000000000000 x20: ffff80000a88b9b8 x19: 0000000000000000 x18: 0000000000000001 x17: 7270642f636d2d6c x16: 73662e3030303030 x15: ffffffffffffffff x14: ffffd59330f1d668 x13: ffff48a8727dc389 x12: ffff48a8727dc386 x11: 0000000000000002 x10: 00008ceaf02f35d4 x9 : 0000000000000012 x8 : 0000000000000000 x7 : 0000000000000006 x6 : ffff80000a88bab0 x5 : 0000000000000000 x4 : 0000000000000000 x3 : ffff80000a88b9e8 x2 : ffff80000a88b9e8 x1 : 0000000000000000 x0 : ffff48a945142b80 Call trace: mc_send_command+0x24/0x1f0 dprc_get_obj_region+0xfc/0x1c0 fsl_mc_device_add+0x340/0x590 fsl_mc_obj_device_add+0xd0/0xf8 dprc_scan_objects+0x1c4/0x340 dprc_scan_container+0x38/0x60 vfio_fsl_mc_probe+0x9c/0xf8 fsl_mc_driver_probe+0x24/0x70 really_probe+0xbc/0x2a8 __driver_probe_device+0x78/0xe0 device_driver_attach+0x30/0x68 bind_store+0xa8/0x130 drv_attr_store+0x24/0x38 sysfs_kf_write+0x44/0x60 kernfs_fop_write_iter+0x128/0x1b8 vfs_write+0x334/0x448 ksys_write+0x68/0xf0 __arm64_sys_write+0x1c/0x28 invoke_syscall+0x44/0x108 el0_svc_common.constprop.1+0x94/0xf8 do_el0_svc+0x38/0xb0 el0_svc+0x20/0x50 el0t_64_sync_handler+0x98/0xc0 el0t_64_sync+0x174/0x178 Code: aa0103f4 a9025bf5 d5384100 b9400801 (79401260) ---[ end trace 0000000000000000 ]--- Fixes: 3c28a76 ("vfio: Add struct device to vfio_device") Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> Message-ID: <20230613160718.29500-1-laurentiu.tudor@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 2fb48d8 ] When a device-mapper device is passing through the inline encryption support of an underlying device, calls to blk_crypto_evict_key() take the blk_crypto_profile::lock of the device-mapper device, then take the blk_crypto_profile::lock of the underlying device (nested). This isn't a real deadlock, but it causes a lockdep report because there is only one lock class for all instances of this lock. Lockdep subclasses don't really work here because the hierarchy of block devices is dynamic and could have more than 2 levels. Instead, register a dynamic lock class for each blk_crypto_profile, and associate that with the lock. This avoids false-positive lockdep reports like the following: ============================================ WARNING: possible recursive locking detected 6.4.0-rc5 #2 Not tainted -------------------------------------------- fscryptctl/1421 is trying to acquire lock: ffffff80829ca418 (&profile->lock){++++}-{3:3}, at: __blk_crypto_evict_key+0x44/0x1c0 but task is already holding lock: ffffff8086b68ca8 (&profile->lock){++++}-{3:3}, at: __blk_crypto_evict_key+0xc8/0x1c0 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&profile->lock); lock(&profile->lock); *** DEADLOCK *** May be due to missing lock nesting notation Fixes: 1b26283 ("block: Keyslot Manager for Inline Encryption") Reported-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20230610061139.212085-1-ebiggers@kernel.org Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 5eda1ad upstream. Thread #1: [122554.641906][ T92] f2fs_getxattr+0xd4/0x5fc -> waiting for f2fs_down_read(&F2FS_I(inode)->i_xattr_sem); [122554.641927][ T92] __f2fs_get_acl+0x50/0x284 [122554.641948][ T92] f2fs_init_acl+0x84/0x54c [122554.641969][ T92] f2fs_init_inode_metadata+0x460/0x5f0 [122554.641990][ T92] f2fs_add_inline_entry+0x11c/0x350 -> Locked dir->inode_page by f2fs_get_node_page() [122554.642009][ T92] f2fs_do_add_link+0x100/0x1e4 [122554.642025][ T92] f2fs_create+0xf4/0x22c [122554.642047][ T92] vfs_create+0x130/0x1f4 Thread #2: [123996.386358][ T92] __get_node_page+0x8c/0x504 -> waiting for dir->inode_page lock [123996.386383][ T92] read_all_xattrs+0x11c/0x1f4 [123996.386405][ T92] __f2fs_setxattr+0xcc/0x528 [123996.386424][ T92] f2fs_setxattr+0x158/0x1f4 -> f2fs_down_write(&F2FS_I(inode)->i_xattr_sem); [123996.386443][ T92] __f2fs_set_acl+0x328/0x430 [123996.386618][ T92] f2fs_set_acl+0x38/0x50 [123996.386642][ T92] posix_acl_chmod+0xc8/0x1c8 [123996.386669][ T92] f2fs_setattr+0x5e0/0x6bc [123996.386689][ T92] notify_change+0x4d8/0x580 [123996.386717][ T92] chmod_common+0xd8/0x184 [123996.386748][ T92] do_fchmodat+0x60/0x124 [123996.386766][ T92] __arm64_sys_fchmodat+0x28/0x3c Cc: <stable@vger.kernel.org> Fixes: 27161f1 "f2fs: avoid race in between read xattr & write xattr" Reviewed-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 5fc8cbe ] pr_info() is called with rtp->cbs_gbl_lock spin lock locked. Because pr_info() calls printk() that might sleep, this will result in BUG like below: [ 0.206455] cblist_init_generic: Setting adjustable number of callback queues. [ 0.206463] [ 0.206464] ============================= [ 0.206464] [ BUG: Invalid wait context ] [ 0.206465] 5.19.0-00428-g9de1f9c8ca51 #5 Not tainted [ 0.206466] ----------------------------- [ 0.206466] swapper/0/1 is trying to lock: [ 0.206467] ffffffffa0167a58 (&port_lock_key){....}-{3:3}, at: serial8250_console_write+0x327/0x4a0 [ 0.206473] other info that might help us debug this: [ 0.206473] context-{5:5} [ 0.206474] 3 locks held by swapper/0/1: [ 0.206474] #0: ffffffff9eb597e0 (rcu_tasks.cbs_gbl_lock){....}-{2:2}, at: cblist_init_generic.constprop.0+0x14/0x1f0 [ 0.206478] #1: ffffffff9eb579c0 (console_lock){+.+.}-{0:0}, at: _printk+0x63/0x7e [ 0.206482] #2: ffffffff9ea77780 (console_owner){....}-{0:0}, at: console_emit_next_record.constprop.0+0x111/0x330 [ 0.206485] stack backtrace: [ 0.206486] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.19.0-00428-g9de1f9c8ca51 #5 [ 0.206488] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-1.fc36 04/01/2014 [ 0.206489] Call Trace: [ 0.206490] <TASK> [ 0.206491] dump_stack_lvl+0x6a/0x9f [ 0.206493] __lock_acquire.cold+0x2d7/0x2fe [ 0.206496] ? stack_trace_save+0x46/0x70 [ 0.206497] lock_acquire+0xd1/0x2f0 [ 0.206499] ? serial8250_console_write+0x327/0x4a0 [ 0.206500] ? __lock_acquire+0x5c7/0x2720 [ 0.206502] _raw_spin_lock_irqsave+0x3d/0x90 [ 0.206504] ? serial8250_console_write+0x327/0x4a0 [ 0.206506] serial8250_console_write+0x327/0x4a0 [ 0.206508] console_emit_next_record.constprop.0+0x180/0x330 [ 0.206511] console_unlock+0xf7/0x1f0 [ 0.206512] vprintk_emit+0xf7/0x330 [ 0.206514] _printk+0x63/0x7e [ 0.206516] cblist_init_generic.constprop.0.cold+0x24/0x32 [ 0.206518] rcu_init_tasks_generic+0x5/0xd9 [ 0.206522] kernel_init_freeable+0x15b/0x2a2 [ 0.206523] ? rest_init+0x160/0x160 [ 0.206526] kernel_init+0x11/0x120 [ 0.206527] ret_from_fork+0x1f/0x30 [ 0.206530] </TASK> [ 0.207018] cblist_init_generic: Setting shift to 1 and lim to 1. This patch moves pr_info() so that it is called without rtp->cbs_gbl_lock locked. Signed-off-by: Shigeru Yoshida <syoshida@redhat.com> Tested-by: "Zhang, Qiang1" <qiang1.zhang@intel.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 5f4fa16 ] We do netif_napi_add() for all allocated q_vectors[], but potentially do netif_napi_del() for part of them, then kfree q_vectors and leave invalid pointers at dev->napi_list. Reproducer: [root@host ~]# cat repro.sh #!/bin/bash pf_dbsf="0000:41:00.0" vf0_dbsf="0000:41:02.0" g_pids=() function do_set_numvf() { echo 2 >/sys/bus/pci/devices/${pf_dbsf}/sriov_numvfs sleep $((RANDOM%3+1)) echo 0 >/sys/bus/pci/devices/${pf_dbsf}/sriov_numvfs sleep $((RANDOM%3+1)) } function do_set_channel() { local nic=$(ls -1 --indicator-style=none /sys/bus/pci/devices/${vf0_dbsf}/net/) [ -z "$nic" ] && { sleep $((RANDOM%3)) ; return 1; } ifconfig $nic 192.168.18.5 netmask 255.255.255.0 ifconfig $nic up ethtool -L $nic combined 1 ethtool -L $nic combined 4 sleep $((RANDOM%3)) } function on_exit() { local pid for pid in "${g_pids[@]}"; do kill -0 "$pid" &>/dev/null && kill "$pid" &>/dev/null done g_pids=() } trap "on_exit; exit" EXIT while :; do do_set_numvf ; done & g_pids+=($!) while :; do do_set_channel ; done & g_pids+=($!) wait Result: [ 4093.900222] ================================================================== [ 4093.900230] BUG: KASAN: use-after-free in free_netdev+0x308/0x390 [ 4093.900232] Read of size 8 at addr ffff88b4dc145640 by task repro.sh/6699 [ 4093.900233] [ 4093.900236] CPU: 10 PID: 6699 Comm: repro.sh Kdump: loaded Tainted: G O --------- -t - 4.18.0 #1 [ 4093.900238] Hardware name: Powerleader PR2008AL/H12DSi-N6, BIOS 2.0 04/09/2021 [ 4093.900239] Call Trace: [ 4093.900244] dump_stack+0x71/0xab [ 4093.900249] print_address_description+0x6b/0x290 [ 4093.900251] ? free_netdev+0x308/0x390 [ 4093.900252] kasan_report+0x14a/0x2b0 [ 4093.900254] free_netdev+0x308/0x390 [ 4093.900261] iavf_remove+0x825/0xd20 [iavf] [ 4093.900265] pci_device_remove+0xa8/0x1f0 [ 4093.900268] device_release_driver_internal+0x1c6/0x460 [ 4093.900271] pci_stop_bus_device+0x101/0x150 [ 4093.900273] pci_stop_and_remove_bus_device+0xe/0x20 [ 4093.900275] pci_iov_remove_virtfn+0x187/0x420 [ 4093.900277] ? pci_iov_add_virtfn+0xe10/0xe10 [ 4093.900278] ? pci_get_subsys+0x90/0x90 [ 4093.900280] sriov_disable+0xed/0x3e0 [ 4093.900282] ? bus_find_device+0x12d/0x1a0 [ 4093.900290] i40e_free_vfs+0x754/0x1210 [i40e] [ 4093.900298] ? i40e_reset_all_vfs+0x880/0x880 [i40e] [ 4093.900299] ? pci_get_device+0x7c/0x90 [ 4093.900300] ? pci_get_subsys+0x90/0x90 [ 4093.900306] ? pci_vfs_assigned.part.7+0x144/0x210 [ 4093.900309] ? __mutex_lock_slowpath+0x10/0x10 [ 4093.900315] i40e_pci_sriov_configure+0x1fa/0x2e0 [i40e] [ 4093.900318] sriov_numvfs_store+0x214/0x290 [ 4093.900320] ? sriov_totalvfs_show+0x30/0x30 [ 4093.900321] ? __mutex_lock_slowpath+0x10/0x10 [ 4093.900323] ? __check_object_size+0x15a/0x350 [ 4093.900326] kernfs_fop_write+0x280/0x3f0 [ 4093.900329] vfs_write+0x145/0x440 [ 4093.900330] ksys_write+0xab/0x160 [ 4093.900332] ? __ia32_sys_read+0xb0/0xb0 [ 4093.900334] ? fput_many+0x1a/0x120 [ 4093.900335] ? filp_close+0xf0/0x130 [ 4093.900338] do_syscall_64+0xa0/0x370 [ 4093.900339] ? page_fault+0x8/0x30 [ 4093.900341] entry_SYSCALL_64_after_hwframe+0x65/0xca [ 4093.900357] RIP: 0033:0x7f16ad4d22c0 [ 4093.900359] Code: 73 01 c3 48 8b 0d d8 cb 2c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d 89 24 2d 00 00 75 10 b8 01 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 31 c3 48 83 ec 08 e8 fe dd 01 00 48 89 04 24 [ 4093.900360] RSP: 002b:00007ffd6491b7f8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 [ 4093.900362] RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 00007f16ad4d22c0 [ 4093.900363] RDX: 0000000000000002 RSI: 0000000001a41408 RDI: 0000000000000001 [ 4093.900364] RBP: 0000000001a41408 R08: 00007f16ad7a1780 R09: 00007f16ae1f2700 [ 4093.900364] R10: 0000000000000001 R11: 0000000000000246 R12: 0000000000000002 [ 4093.900365] R13: 0000000000000001 R14: 00007f16ad7a0620 R15: 0000000000000001 [ 4093.900367] [ 4093.900368] Allocated by task 820: [ 4093.900371] kasan_kmalloc+0xa6/0xd0 [ 4093.900373] __kmalloc+0xfb/0x200 [ 4093.900376] iavf_init_interrupt_scheme+0x63b/0x1320 [iavf] [ 4093.900380] iavf_watchdog_task+0x3d51/0x52c0 [iavf] [ 4093.900382] process_one_work+0x56a/0x11f0 [ 4093.900383] worker_thread+0x8f/0xf40 [ 4093.900384] kthread+0x2a0/0x390 [ 4093.900385] ret_from_fork+0x1f/0x40 [ 4093.900387] 0xffffffffffffffff [ 4093.900387] [ 4093.900388] Freed by task 6699: [ 4093.900390] __kasan_slab_free+0x137/0x190 [ 4093.900391] kfree+0x8b/0x1b0 [ 4093.900394] iavf_free_q_vectors+0x11d/0x1a0 [iavf] [ 4093.900397] iavf_remove+0x35a/0xd20 [iavf] [ 4093.900399] pci_device_remove+0xa8/0x1f0 [ 4093.900400] device_release_driver_internal+0x1c6/0x460 [ 4093.900401] pci_stop_bus_device+0x101/0x150 [ 4093.900402] pci_stop_and_remove_bus_device+0xe/0x20 [ 4093.900403] pci_iov_remove_virtfn+0x187/0x420 [ 4093.900404] sriov_disable+0xed/0x3e0 [ 4093.900409] i40e_free_vfs+0x754/0x1210 [i40e] [ 4093.900415] i40e_pci_sriov_configure+0x1fa/0x2e0 [i40e] [ 4093.900416] sriov_numvfs_store+0x214/0x290 [ 4093.900417] kernfs_fop_write+0x280/0x3f0 [ 4093.900418] vfs_write+0x145/0x440 [ 4093.900419] ksys_write+0xab/0x160 [ 4093.900420] do_syscall_64+0xa0/0x370 [ 4093.900421] entry_SYSCALL_64_after_hwframe+0x65/0xca [ 4093.900422] 0xffffffffffffffff [ 4093.900422] [ 4093.900424] The buggy address belongs to the object at ffff88b4dc144200 which belongs to the cache kmalloc-8k of size 8192 [ 4093.900425] The buggy address is located 5184 bytes inside of 8192-byte region [ffff88b4dc144200, ffff88b4dc146200) [ 4093.900425] The buggy address belongs to the page: [ 4093.900427] page:ffffea00d3705000 refcount:1 mapcount:0 mapping:ffff88bf04415c80 index:0x0 compound_mapcount: 0 [ 4093.900430] flags: 0x10000000008100(slab|head) [ 4093.900433] raw: 0010000000008100 dead000000000100 dead000000000200 ffff88bf04415c80 [ 4093.900434] raw: 0000000000000000 0000000000030003 00000001ffffffff 0000000000000000 [ 4093.900434] page dumped because: kasan: bad access detected [ 4093.900435] [ 4093.900435] Memory state around the buggy address: [ 4093.900436] ffff88b4dc145500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 4093.900437] ffff88b4dc145580: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 4093.900438] >ffff88b4dc145600: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 4093.900438] ^ [ 4093.900439] ffff88b4dc145680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 4093.900440] ffff88b4dc145700: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 4093.900440] ================================================================== Although the patch #2 (of 2) can avoid the issue triggered by this repro.sh, there still are other potential risks that if num_active_queues is changed to less than allocated q_vectors[] by unexpected, the mismatched netif_napi_add/del() can also cause UAF. Since we actually call netif_napi_add() for all allocated q_vectors unconditionally in iavf_alloc_q_vectors(), so we should fix it by letting netif_napi_del() match to netif_napi_add(). Fixes: 5eae00c ("i40evf: main driver core") Signed-off-by: Ding Hui <dinghui@sangfor.com.cn> Cc: Donglin Peng <pengdonglin@sangfor.com.cn> Cc: Huang Cun <huangcun@sangfor.com.cn> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Madhu Chittim <madhu.chittim@intel.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 7f7cfcb ] In hci_cs_disconnect, we do hci_conn_del even if disconnection failed. ISO, L2CAP and SCO connections refer to the hci_conn without hci_conn_get, so disconn_cfm must be called so they can clean up their conn, otherwise use-after-free occurs. ISO: ========================================================== iso_sock_connect:880: sk 00000000eabd6557 iso_connect_cis:356: 70:1a:b8:98:ff:a2 -> 28:3d:c2:4a:7e:da ... iso_conn_add:140: hcon 000000001696f1fd conn 00000000b6251073 hci_dev_put:1487: hci0 orig refcnt 17 __iso_chan_add:214: conn 00000000b6251073 iso_sock_clear_timer:117: sock 00000000eabd6557 state 3 ... hci_rx_work:4085: hci0 Event packet hci_event_packet:7601: hci0: event 0x0f hci_cmd_status_evt:4346: hci0: opcode 0x0406 hci_cs_disconnect:2760: hci0: status 0x0c hci_sent_cmd_data:3107: hci0 opcode 0x0406 hci_conn_del:1151: hci0 hcon 000000001696f1fd handle 2560 hci_conn_unlink:1102: hci0: hcon 000000001696f1fd hci_conn_drop:1451: hcon 00000000d8521aaf orig refcnt 2 hci_chan_list_flush:2780: hcon 000000001696f1fd hci_dev_put:1487: hci0 orig refcnt 21 hci_dev_put:1487: hci0 orig refcnt 20 hci_req_cmd_complete:3978: opcode 0x0406 status 0x0c ... <no iso_* activity on sk/conn> ... iso_sock_sendmsg:1098: sock 00000000dea5e2e0, sk 00000000eabd6557 BUG: kernel NULL pointer dereference, address: 0000000000000668 PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP PTI Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 RIP: 0010:iso_sock_sendmsg (net/bluetooth/iso.c:1112) bluetooth ========================================================== L2CAP: ================================================================== hci_cmd_status_evt:4359: hci0: opcode 0x0406 hci_cs_disconnect:2760: hci0: status 0x0c hci_sent_cmd_data:3085: hci0 opcode 0x0406 hci_conn_del:1151: hci0 hcon ffff88800c999000 handle 3585 hci_conn_unlink:1102: hci0: hcon ffff88800c999000 hci_chan_list_flush:2780: hcon ffff88800c999000 hci_chan_del:2761: hci0 hcon ffff88800c999000 chan ffff888018ddd280 ... BUG: KASAN: slab-use-after-free in hci_send_acl+0x2d/0x540 [bluetooth] Read of size 8 at addr ffff888018ddd298 by task bluetoothd/1175 CPU: 0 PID: 1175 Comm: bluetoothd Tainted: G E 6.4.0-rc4+ #2 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x5b/0x90 print_report+0xcf/0x670 ? __virt_addr_valid+0xf8/0x180 ? hci_send_acl+0x2d/0x540 [bluetooth] kasan_report+0xa8/0xe0 ? hci_send_acl+0x2d/0x540 [bluetooth] hci_send_acl+0x2d/0x540 [bluetooth] ? __pfx___lock_acquire+0x10/0x10 l2cap_chan_send+0x1fd/0x1300 [bluetooth] ? l2cap_sock_sendmsg+0xf2/0x170 [bluetooth] ? __pfx_l2cap_chan_send+0x10/0x10 [bluetooth] ? lock_release+0x1d5/0x3c0 ? mark_held_locks+0x1a/0x90 l2cap_sock_sendmsg+0x100/0x170 [bluetooth] sock_write_iter+0x275/0x280 ? __pfx_sock_write_iter+0x10/0x10 ? __pfx___lock_acquire+0x10/0x10 do_iter_readv_writev+0x176/0x220 ? __pfx_do_iter_readv_writev+0x10/0x10 ? find_held_lock+0x83/0xa0 ? selinux_file_permission+0x13e/0x210 do_iter_write+0xda/0x340 vfs_writev+0x1b4/0x400 ? __pfx_vfs_writev+0x10/0x10 ? __seccomp_filter+0x112/0x750 ? populate_seccomp_data+0x182/0x220 ? __fget_light+0xdf/0x100 ? do_writev+0x19d/0x210 do_writev+0x19d/0x210 ? __pfx_do_writev+0x10/0x10 ? mark_held_locks+0x1a/0x90 do_syscall_64+0x60/0x90 ? lockdep_hardirqs_on_prepare+0x149/0x210 ? do_syscall_64+0x6c/0x90 ? lockdep_hardirqs_on_prepare+0x149/0x210 entry_SYSCALL_64_after_hwframe+0x72/0xdc RIP: 0033:0x7ff45cb23e64 Code: 15 d1 1f 0d 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 80 3d 9d a7 0d 00 00 74 13 b8 14 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 54 c3 0f 1f 00 48 83 ec 28 89 54 24 1c 48 89 RSP: 002b:00007fff21ae09b8 EFLAGS: 00000202 ORIG_RAX: 0000000000000014 RAX: ffffffffffffffda RBX: 0000000000000001 RCX: 00007ff45cb23e64 RDX: 0000000000000001 RSI: 00007fff21ae0aa0 RDI: 0000000000000017 RBP: 00007fff21ae0aa0 R08: 000000000095a8a0 R09: 0000607000053f40 R10: 0000000000000001 R11: 0000000000000202 R12: 00007fff21ae0ac0 R13: 00000fffe435c150 R14: 00007fff21ae0a80 R15: 000060f000000040 </TASK> Allocated by task 771: kasan_save_stack+0x33/0x60 kasan_set_track+0x25/0x30 __kasan_kmalloc+0xaa/0xb0 hci_chan_create+0x67/0x1b0 [bluetooth] l2cap_conn_add.part.0+0x17/0x590 [bluetooth] l2cap_connect_cfm+0x266/0x6b0 [bluetooth] hci_le_remote_feat_complete_evt+0x167/0x310 [bluetooth] hci_event_packet+0x38d/0x800 [bluetooth] hci_rx_work+0x287/0xb20 [bluetooth] process_one_work+0x4f7/0x970 worker_thread+0x8f/0x620 kthread+0x17f/0x1c0 ret_from_fork+0x2c/0x50 Freed by task 771: kasan_save_stack+0x33/0x60 kasan_set_track+0x25/0x30 kasan_save_free_info+0x2e/0x50 ____kasan_slab_free+0x169/0x1c0 slab_free_freelist_hook+0x9e/0x1c0 __kmem_cache_free+0xc0/0x310 hci_chan_list_flush+0x46/0x90 [bluetooth] hci_conn_cleanup+0x7d/0x330 [bluetooth] hci_cs_disconnect+0x35d/0x530 [bluetooth] hci_cmd_status_evt+0xef/0x2b0 [bluetooth] hci_event_packet+0x38d/0x800 [bluetooth] hci_rx_work+0x287/0xb20 [bluetooth] process_one_work+0x4f7/0x970 worker_thread+0x8f/0x620 kthread+0x17f/0x1c0 ret_from_fork+0x2c/0x50 ================================================================== Fixes: b8d2905 ("Bluetooth: clean up connection in hci_cs_disconnect") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

Marek Vasut and others added 2 commits August 10, 2020 14:22

fixup! ARM: dts: bcm283x: Add overlays for Revolution Pi by KUNBUS

8c8df7a

Add initial support for the KSZ8795 Ethernet switch on the RevPi Flat. Signed-off-by: Lukas Wunner <lukas@wunner.de>

l1k assigned iluminat23 and linosanfilippo-kunbus Aug 10, 2020

iluminat23 removed their assignment Aug 10, 2020

nbuchwitz closed this Feb 9, 2022

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

Add initial support for the KSZ8795 Ethernet switch on the RevPi Flat #2

Add initial support for the KSZ8795 Ethernet switch on the RevPi Flat #2

l1k commented Aug 10, 2020

nbuchwitz commented Jan 26, 2022

iluminat23 commented Jan 27, 2022

l1k commented Jan 27, 2022 •

edited

Loading

nbuchwitz commented Feb 9, 2022

Add initial support for the KSZ8795 Ethernet switch on the RevPi Flat #2

Add initial support for the KSZ8795 Ethernet switch on the RevPi Flat #2

Conversation

l1k commented Aug 10, 2020

nbuchwitz commented Jan 26, 2022

iluminat23 commented Jan 27, 2022

l1k commented Jan 27, 2022 • edited Loading

nbuchwitz commented Feb 9, 2022

l1k commented Jan 27, 2022 •

edited

Loading