Skip to content

MechWild/murphpad-zmk-config

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

19 Commits
 
 
 
 
 
 
 
 

Repository files navigation

MurphPad ZMK Config

Instructions

  1. You will need to sign up for a GitHub account, and fork this repository so you can edit it.
  2. Navigate to the Actions tab and click the "I understand my workflows, go ahead and run them" button to enable builds. Actions tab with "I understand my workflows" button
  3. Edit config/murphpad.conf to enable/disable features. Edit config/murphpad.keymap to change the keymap. Lastly, make sure the build.yaml file has your board in the "boards" list.
  4. After committing your changes, your firmware will begin compiling. Assuming there are no typos or other problems, it will eventually be downloadable from the Actions tab.
  5. Flash the firmware that matches the board you're using, e.g. murphpad-nice_nano_v2-zmk.uf2 for a nice!nano v2.

Common Questions/Problems

There was an error and the build didn't finish.

There is probably an error in your keymap.

Carefully double-check the last changes you made. ZMK syntax is very different from QMK syntax. Note that when editing keymaps, each ZMK code is generally preceded by a reference categorizing what that code does.

For example: the letter "Z" is categorized as a key press. To add the letter "Z" to a keymap, it must be written &kp Z.

A few more examples below:

QMK ZMK
KC_A &kp A
QK_REBOOT &sys_reset
LT(1, KC_SPACE) &lt 1 SPACE

There are many, many more differences. Don't forget to check the ZMK docs.

The OLED/RGB/encoder(s) don't work.

Double-check the features in the config/murphpad.conf file.

And double-check the Kconfig file in the build results to make sure what you've enabled is really enabled. As of mid-July 2022, there are also some issues regarding default board/shield configurations taking precedence over user configurations.

The OLED can be a bit finicky.

There is a known issue with OLEDs not being re-initialized after power off; please check that pull request for any updates and/or possible workarounds.

Try the following:

  1. Wait at least one minute and press the physical reset button on the board once.
  2. If CONFIG_ZMK_RGB_UNDERGLOW_EXT_POWER=y is set in config/murphpad.conf, turn on RGB. Then try step 1.
  3. Add &ext_power EP_ON to your keymap and press the key to make sure external power is on. Then try step 2.

How can I turn off the RGB without turning the OLED off?

Since the RGB LEDs and the OLED are powered by the same pin (VCC), both will be turned off if power is cut to that pin. There are two ways to resolve this:

Set CONFIG_ZMK_RGB_UNDERGLOW_EXT_POWER=n in config/murphpad.conf.

This configuration setting will allow you to turn the RGB LEDs off without cutting power. It is the default in this repository.

⚠️ Not cutting power to the LEDs will have a significant impact on battery life. Check the ZMK Power Profiler and set your expectations accordingly.

Connect OLED VCC to a different power source.

If the board powering your MurphPad has an alternate power pin (often labeled RAW), connecting VCC on the OLED to it will prevent the display from being affected when board VCC is toggled off.

Later revisions of the MurphPad add jumpers to simplify this process for boards with alternate power pins in the same place as nice!nano RAW, but this can be done on all known versions.

⚠️ If using a nice!nano v2 without a battery, its RAW pin does not always deliver consistent voltage. This can result in the OLED turning off immediately after boot, or failing to turn on. Unfortunately, the only guaranteed fix is to add a battery; occasionally it will work after a reset as described in step 1.


Instructions for MurphPad v3.1

photo by Tokolist#9634

  1. Disconnect OLED VCC from LED8 by cutting the trace on the PCB.
  2. Solder a wire connecting from the RAW pin on the PCB to the OLED VCC pin.
    • @tokolist demonstrates an elegant solution by wiring RAW to the unused LED strip connection, but the wire can be connected directly.

⚠️ If the LED strip is in use, you will also need to cut the trace between its 5V and OLED VCC, and rewire the strip to board VCC.

Instructions for MurphPad Rev2 v1.2

photo by @honorless

  1. Disconnect OLED VCC from LED8 by cutting the J1 jumper.
  2. Connect OLED VCC to board RAW by closing the J2 jumper.

⚠️ If your board's additional power pin is not in the same place, you will need to wire that yourself instead of closing J2.


After disconnecting the MurphPad from Bluetooth, it won't reconnect.

Forget the Bluetooth connection on both the MurphPad and the device, then try re-pairing.

If you don't remember which profile on the MurphPad was used to connect to a specific device, this may mean cycling through each (&bt BT_PRV/&bt BT_NXT) and clearing them (&bt BT_CLR) one by one. See ZMK's documentation for more info.

As a last resort, try flashing the settings_reset firmware for your board; this will force-clear everything.

Further Troubleshooting Resources

About

ZMK config files to build firmware for the Murphpad.

Resources

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published