MarlinFirmware · thinkyhead · May 19, 2022 · May 17, 2022 · May 19, 2022
diff --git a/config/examples/AnyCubic/Chiron/Configuration_adv.h b/config/examples/AnyCubic/Chiron/Configuration_adv.h
@@ -1480,8 +1480,8 @@
     //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     #define POWER_LOSS_PIN           79 // Pin to detect power loss. Set to -1 to disable default pin on boards without module.
     #define POWER_LOSS_STATE        LOW // State of pin indicating power loss
-    //#define POWER_LOSS_PULLUP         // Set pullup / pulldown as appropriate for your sensor
-    #define POWER_LOSS_PULLDOWN
+    #define POWER_LOSS_PULLUP           // Set pullup / pulldown as appropriate for your sensor
+    //#define POWER_LOSS_PULLDOWN
     #define POWER_LOSS_PURGE_LEN      1 // (mm) Length of filament to purge on resume
     //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
 

diff --git a/config/examples/AnyCubic/i3 Mega/Configuration.h b/config/examples/AnyCubic/i3 Mega/Configuration.h
@@ -20,6 +20,8 @@
  *
  */
 #pragma once
+#error "Don't build with import-2.0.x configurations!"
+#error "Use the 'bugfix...' or 'release...' configurations matching your Marlin version."
 
 //#define I3MEGA_HAS_BLTOUCH
 //#define I3MEGA_HAS_TMC2208
@@ -969,7 +971,7 @@
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
 #define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
 #define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
 #define I_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define J_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define K_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.

diff --git a/config/examples/BIQU/B1 - SKR 1.4/Configuration.h b/config/examples/BIQU/B1 - SKR 1.4/Configuration.h
@@ -20,8 +20,11 @@
  *
  */
 #pragma once
+#error "Don't build with import-2.0.x configurations!"
+#error "Use the 'bugfix...' or 'release...' configurations matching your Marlin version."
 
-//#define B1_WITH_BLTOUCH
+// Enable this option for BLTouch support
+//#define B1_USE_BLTOUCH
 
 /**
  * Configuration.h
@@ -948,7 +951,7 @@
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
 #define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
 #define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
-#ifdef B1_WITH_BLTOUCH
+#ifdef B1_USE_BLTOUCH
   #define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #else
   #define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
@@ -1179,7 +1182,7 @@
 /**
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
-#ifdef B1_WITH_BLTOUCH
+#ifdef B1_USE_BLTOUCH
   #define BLTOUCH
 #endif
 
@@ -1344,7 +1347,7 @@
  * A total of 2 does fast/slow probes with a weighted average.
  * A total of 3 or more adds more slow probes, taking the average.
  */
-#ifdef B1_WITH_BLTOUCH
+#ifdef B1_USE_BLTOUCH
   #define MULTIPLE_PROBING 2
 #endif
 //#define EXTRA_PROBING    1
@@ -1534,7 +1537,7 @@
 #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
   #define MIN_SOFTWARE_ENDSTOP_X
   #define MIN_SOFTWARE_ENDSTOP_Y
-  #ifndef B1_WITH_BLTOUCH
+  #ifndef B1_USE_BLTOUCH
     #define MIN_SOFTWARE_ENDSTOP_Z
   #endif
   #define MIN_SOFTWARE_ENDSTOP_I
@@ -1679,7 +1682,7 @@
 //#define AUTO_BED_LEVELING_3POINT
 //#define AUTO_BED_LEVELING_LINEAR
 //#define AUTO_BED_LEVELING_UBL
-#ifdef B1_WITH_BLTOUCH
+#ifdef B1_USE_BLTOUCH
   #define AUTO_BED_LEVELING_BILINEAR
 #else
   #define MESH_BED_LEVELING
@@ -2158,7 +2161,7 @@
  *
  * View the current statistics with M78.
  */
-#define PRINTCOUNTER
+//#define PRINTCOUNTER
 #if ENABLED(PRINTCOUNTER)
   #define PRINTCOUNTER_SAVE_INTERVAL 60 // (minutes) EEPROM save interval during print
 #endif

diff --git a/config/examples/BIQU/B1 - SKR 1.4/README.md b/config/examples/BIQU/B1 - SKR 1.4/README.md
@@ -4,6 +4,6 @@ Compile with the `LPC1768` environment.
 
 ## BLTouch Probe Support
 
-Enable `B1_USE_BLTOUCH` for probe customizations.
+Uncomment `B1_USE_BLTOUCH` for probe customizations.
 
 This configuration retains the use of homing with a Z limit switch. If you want to home with the BLTouch probe, remove your Z limit switch & bracket and enable (uncomment) `USE_PROBE_FOR_Z_HOMING` and `Z_SAFE_HOMING`. Change `Z_MIN_ENDSTOP_INVERTING` from `true` to `false`.
diff --git a/config/examples/BIQU/B1 - SKR 2/Configuration.h b/config/examples/BIQU/B1 - SKR 2/Configuration.h
@@ -20,8 +20,11 @@
  *
  */
 #pragma once
+#error "Don't build with import-2.0.x configurations!"
+#error "Use the 'bugfix...' or 'release...' configurations matching your Marlin version."
 
-//#define B1_WITH_BLTOUCH
+// Enable this option for BLTouch support
+//#define B1_USE_BLTOUCH
 
 /**
  * Configuration.h
@@ -948,7 +951,7 @@
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
 #define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
 #define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
-#ifdef B1_WITH_BLTOUCH
+#ifdef B1_USE_BLTOUCH
   #define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #else
   #define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
@@ -1179,7 +1182,7 @@
 /**
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
-#ifdef B1_WITH_BLTOUCH
+#ifdef B1_USE_BLTOUCH
   #define BLTOUCH
 #endif
 
@@ -1344,7 +1347,7 @@
  * A total of 2 does fast/slow probes with a weighted average.
  * A total of 3 or more adds more slow probes, taking the average.
  */
-#ifdef B1_WITH_BLTOUCH
+#ifdef B1_USE_BLTOUCH
   #define MULTIPLE_PROBING 2
 #endif
 //#define EXTRA_PROBING    1
@@ -1534,7 +1537,7 @@
 #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
   #define MIN_SOFTWARE_ENDSTOP_X
   #define MIN_SOFTWARE_ENDSTOP_Y
-  #ifndef B1_WITH_BLTOUCH
+  #ifndef B1_USE_BLTOUCH
     #define MIN_SOFTWARE_ENDSTOP_Z
   #endif
   #define MIN_SOFTWARE_ENDSTOP_I
@@ -1679,7 +1682,7 @@
 //#define AUTO_BED_LEVELING_3POINT
 //#define AUTO_BED_LEVELING_LINEAR
 //#define AUTO_BED_LEVELING_UBL
-#ifdef B1_WITH_BLTOUCH
+#ifdef B1_USE_BLTOUCH
   #define AUTO_BED_LEVELING_BILINEAR
 #else
   #define MESH_BED_LEVELING

diff --git a/config/examples/BIQU/B1 - SKR 2/README.md b/config/examples/BIQU/B1 - SKR 2/README.md
@@ -4,6 +4,6 @@ Flash drive support is enabled, but jumpers to enable support may not have been
 
 ## BLTouch Probe Support
 
-Enable `B1_USE_BLTOUCH` for probe customizations.
+Uncomment `B1_USE_BLTOUCH` for probe customizations.
 
 This configuration retains the use of homing with a Z limit switch. If you want to home with the BLTouch probe, remove your Z limit switch & bracket and enable (uncomment) `USE_PROBE_FOR_Z_HOMING` and `Z_SAFE_HOMING`. Change `Z_MIN_ENDSTOP_INVERTING` from `true` to `false`.
diff --git a/config/examples/CTC/A13/Configuration.h b/config/examples/CTC/A13/Configuration.h
@@ -89,7 +89,7 @@
 #define SHOW_BOOTSCREEN
 
 // Show the bitmap in Marlin/_Bootscreen.h on startup.
-#define SHOW_CUSTOM_BOOTSCREEN
+//#define SHOW_CUSTOM_BOOTSCREEN
 
 // Show the bitmap in Marlin/_Statusscreen.h on the status screen.
 #define CUSTOM_STATUS_SCREEN_IMAGE
@@ -2248,7 +2248,7 @@
  * just remove some extraneous menu items to recover space.
  */
 //#define NO_LCD_MENUS
-//#define SLIM_LCD_MENUS
+#define SLIM_LCD_MENUS
 
 //
 // ENCODER SETTINGS

diff --git a/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h b/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h
@@ -3037,7 +3037,7 @@
 #endif
 
 // Support for Adafruit NeoPixel LED driver
-#define NEOPIXEL_LED
+//#define NEOPIXEL_LED
 #if ENABLED(NEOPIXEL_LED)
   #define NEOPIXEL_TYPE           NEO_GRB // NEO_GRBW, NEO_RGBW, NEO_GRB, NEO_RBG, etc.
                                           // See https://github.com/adafruit/Adafruit_NeoPixel/blob/master/Adafruit_NeoPixel.h

diff --git a/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration_adv.h b/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration_adv.h
@@ -1370,7 +1370,7 @@
    * LED Control Menu
    * Add LED Control to the LCD menu
    */
-  #define LED_CONTROL_MENU
+  //#define LED_CONTROL_MENU
   #if ENABLED(LED_CONTROL_MENU)
     #define LED_COLOR_PRESETS                 // Enable the Preset Color menu option
     //#define NEO2_COLOR_PRESETS              // Enable a second NeoPixel Preset Color menu option
@@ -4481,7 +4481,7 @@
 //
 // M43 - display pin status, toggle pins, watch pins, watch endstops & toggle LED, test servo probe
 //
-#define PINS_DEBUGGING
+//#define PINS_DEBUGGING
 
 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE

diff --git a/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h b/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h
@@ -2988,7 +2988,7 @@
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
 // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.
-//#define FAN_SOFT_PWM
+#define FAN_SOFT_PWM
 
 // Incrementing this by 1 will double the software PWM frequency,
 // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.

diff --git a/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h b/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h
@@ -2976,7 +2976,7 @@
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
 // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.
-//#define FAN_SOFT_PWM
+#define FAN_SOFT_PWM
 
 // Incrementing this by 1 will double the software PWM frequency,
 // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.

diff --git a/config/examples/Creality/CR-10 S5/CrealityV2.2-BLTouch/Configuration.h b/config/examples/Creality/CR-10 S5/CrealityV2.2-BLTouch/Configuration.h
@@ -2977,7 +2977,7 @@
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
 // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.
-//#define FAN_SOFT_PWM
+#define FAN_SOFT_PWM
 
 // Incrementing this by 1 will double the software PWM frequency,
 // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.

diff --git a/config/examples/Creality/CR-10S/CrealityV1/Configuration.h b/config/examples/Creality/CR-10S/CrealityV1/Configuration.h
@@ -2974,7 +2974,7 @@
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
 // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.
-//#define FAN_SOFT_PWM
+#define FAN_SOFT_PWM
 
 // Incrementing this by 1 will double the software PWM frequency,
 // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.

diff --git a/config/examples/Creality/CR-30 PrintMill/Configuration.h b/config/examples/Creality/CR-30 PrintMill/Configuration.h
@@ -1079,7 +1079,7 @@
   #endif
 #endif
 
-#define DEFAULT_EJERK    5.0  // May be used by Linear Advance
+#define DEFAULT_EJERK   10.0  // May be used by Linear Advance
 
 /**
  * Junction Deviation Factor

diff --git a/config/examples/Creality/CR-6 SE/Configuration.h b/config/examples/Creality/CR-6 SE/Configuration.h
@@ -2734,6 +2734,7 @@
 // CR-6 OEM touch screen. A DWIN display with touch.
 //
 #define DWIN_CREALITY_TOUCHLCD
+#define LCD_SERIAL_PORT 3
 
 //
 // Touch-screen LCD for Malyan M200/M300 printers

diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration_adv.h
@@ -4484,7 +4484,7 @@
 //
 // M43 - display pin status, toggle pins, watch pins, watch endstops & toggle LED, test servo probe
 //
-#define PINS_DEBUGGING
+//#define PINS_DEBUGGING
 
 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE

diff --git a/config/examples/Creality/Ender-3 S1/Configuration.h b/config/examples/Creality/Ender-3 S1/Configuration.h
@@ -1118,7 +1118,7 @@
  * The probe replaces the Z-MIN endstop and is used for Z homing.
  * (Automatically enables USE_PROBE_FOR_Z_HOMING.)
  */
-#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
+//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 
 // Force the use of the probe for Z-axis homing
 //#define USE_PROBE_FOR_Z_HOMING
@@ -1799,7 +1799,7 @@
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */
-#define LCD_BED_LEVELING
+//#define LCD_BED_LEVELING
 
 #if ENABLED(LCD_BED_LEVELING)
   #define MESH_EDIT_Z_STEP  0.025 // (mm) Step size while manually probing Z axis.

diff --git a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h
@@ -3043,7 +3043,7 @@
 #endif
 
 // Support for Adafruit NeoPixel LED driver
-#define NEOPIXEL_LED
+//#define NEOPIXEL_LED
 #if ENABLED(NEOPIXEL_LED)
   #define NEOPIXEL_TYPE          NEO_GRBW // NEO_GRBW, NEO_RGBW, NEO_GRB, NEO_RBG, etc.
                                           // See https://github.com/adafruit/Adafruit_NeoPixel/blob/master/Adafruit_NeoPixel.h

diff --git a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration_adv.h b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration_adv.h
@@ -1370,7 +1370,7 @@
    * LED Control Menu
    * Add LED Control to the LCD menu
    */
-  #define LED_CONTROL_MENU
+  //#define LED_CONTROL_MENU
   #if ENABLED(LED_CONTROL_MENU)
     #define LED_COLOR_PRESETS                 // Enable the Preset Color menu option
     //#define NEO2_COLOR_PRESETS              // Enable a second NeoPixel Preset Color menu option
@@ -4481,7 +4481,7 @@
 //
 // M43 - display pin status, toggle pins, watch pins, watch endstops & toggle LED, test servo probe
 //
-#define PINS_DEBUGGING
+//#define PINS_DEBUGGING
 
 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE

diff --git a/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h b/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h
@@ -109,7 +109,7 @@
  *
  * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  */
-#define SERIAL_PORT -1
+#define SERIAL_PORT 1
 
 /**
  * Serial Port Baud Rate
@@ -130,7 +130,7 @@
  * Currently Ethernet (-2) is only supported on Teensy 4.1 boards.
  * :[-2, -1, 0, 1, 2, 3, 4, 5, 6, 7]
  */
-#define SERIAL_PORT_2 1
+//#define SERIAL_PORT_2 -1
 //#define BAUDRATE_2 250000   // Enable to override BAUDRATE
 
 /**

diff --git a/config/examples/Creality/Ender-5 Plus/Configuration_adv.h b/config/examples/Creality/Ender-5 Plus/Configuration_adv.h
@@ -1773,7 +1773,6 @@
 // Additional options for DGUS / DWIN displays
 //
 #if HAS_DGUS_LCD
-  #define LCD_SERIAL_PORT 2
   #define LCD_BAUDRATE 115200
 
   #define DGUS_RX_BUFFER_SIZE 128

diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration.h
@@ -20,7 +20,10 @@
  *
  */
 #pragma once
+#error "Don't build with import-2.0.x configurations!"
+#error "Use the 'bugfix...' or 'release...' configurations matching your Marlin version."
 
+// Enable this option for BLTouch support
 //#define E5_USE_BLTOUCH
 
 /**
-Original file line number
+Diff line change
@@ Expand Up / @@ -1079,7 +1079,7 @@ @@
       #endif
     #endif
-    #define DEFAULT_EJERK    5.0  // May be used by Linear Advance
+    #define DEFAULT_EJERK   10.0  // May be used by Linear Advance
     /**
      * Junction Deviation Factor
@@ Expand Down @@