-
|
Highlights of 2.10 says New "Eddie the Edgehog" default splash screen - on color display radios also shows the current version of EdgeTX installed. Just updated successfully (inc SD Card) but still have the old splashscreen and no version number on startup. Did I miss something? Also, volume of welcome message is briefly high on start up then drops to set volume. Previously it behaved as per set volume. |
Beta Was this translation helpful? Give feedback.
Replies: 4 comments 3 replies
-
If when you check in Radio Settings -> Version it says you are running 2.10 and not 2.9 or earlier, you must have a custom splash screen screen (i.e. there is a Not sure about what could be causing the volume level to change... given there is also an option to inhibit the startup sound being played, it should have also read the volume level configured and then honor that, maybe something is being read out of sequence. |
Beta Was this translation helpful? Give feedback.
-
|
Thanks Peter. I just had the default original splashscreen but thanks to your reply I now realise it's a custom image in the images folder - hadn't noticed that before! Yeh, the sound thing is a minor issue, as you say it must be loading the message ahead of the volume setting but at least I can switch off the welcome message now... could get a bit annoying for the rest of the family if I'm messing around with the radio in the evenings! |
Beta Was this translation helpful? Give feedback.
-
|
I have edgetx v 2.9.2 on a Radiomaster TX16s and it will NOT update to vers. 2.10.1 Tried Flash Bootloader and Companion. Both say flashed and complete, BUT the vers listed in the system is still 2.9.2 Providence!!!!!!!!!! |
Beta Was this translation helpful? Give feedback.
-
Beta Was this translation helpful? Give feedback.
-
|
If you did "flash bootloader", you only updated the bootloader, not the
firmware. Next step is to use the bootloader to update the firmware.
When you used Companion, was this is the radio off when you connected it to
the computer? And did it take over a minute to flash the firmware?
Otherwise you may have done something else, like syncing the SD card after
downloading the firmware to your computer?
…On Wed, 26 June 2024, 6:40 am Sotm12, ***@***.***> wrote:
I have edgetx v 2.9.2 on a Radiomaster TX16s and it will NOT update to
vers. 2.10.1 Tried Flash Bootloader and Companion. Both say flashed and
complete, BUT the vers listed in the system is still 2.9.2
Providence!!!!!!!!!!
—
Reply to this email directly, view it on GitHub
<#5001 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ABJ66KIJEE6QEPW4A4SUKB3ZJHIVBAVCNFSM6AAAAABHVBZQOOVHI2DSMVQWIX3LMV43SRDJONRXK43TNFXW4Q3PNVWWK3TUHM4TQNZVG44DO>
.
You are receiving this because you commented.Message ID:
***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
|
Thanks for the quick reply. I just got the nightly version update from Github and that update worked. The previous one would NOT. And yes I know how to put the radio in DFU mode. |
Beta Was this translation helpful? Give feedback.
-
|
It was flashed with Bootloader sorry left out the “with”.
From: Peter Feerick
Sent: Tuesday, June 25, 2024 1:49 PM
To: EdgeTX/edgetx
Cc: Sotm12 ; Comment
Subject: Re: [EdgeTX/edgetx] Couple of issues with update to 2.10 (Discussion #5001)
If you did "flash bootloader", you only updated the bootloader, not the
firmware. Next step is to use the bootloader to update the firmware.
When you used Companion, was this is the radio off when you connected it to
the computer? And did it take over a minute to flash the firmware?
Otherwise you may have done something else, like syncing the SD card after
downloading the firmware to your computer?
On Wed, 26 June 2024, 6:40 am Sotm12, ***@***.***> wrote:
I have edgetx v 2.9.2 on a Radiomaster TX16s and it will NOT update to
vers. 2.10.1 Tried Flash Bootloader and Companion. Both say flashed and
complete, BUT the vers listed in the system is still 2.9.2
Providence!!!!!!!!!!
—
Reply to this email directly, view it on GitHub
<#5001 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ABJ66KIJEE6QEPW4A4SUKB3ZJHIVBAVCNFSM6AAAAABHVBZQOOVHI2DSMVQWIX3LMV43SRDJONRXK43TNFXW4Q3PNVWWK3TUHM4TQNZVG44DO>
.
You are receiving this because you commented.Message ID:
***@***.***>
—
Reply to this email directly, view it on GitHub, or unsubscribe.
You are receiving this because you commented.Message ID: ***@***.***>
|
Beta Was this translation helpful? Give feedback.
If when you check in Radio Settings -> Version it says you are running 2.10 and not 2.9 or earlier, you must have a custom splash screen screen (i.e. there is a
/IMAGES/splash.pngfile).Not sure about what could be causing the volume level to change... given there is also an option to inhibit the startup sound being played, it should have also read the volume level configured and then honor that, maybe something is being read out of sequence.