Plugins for version v3.4

This release holds the following plugins:

Endstops Monitor

This is a simple demo plugin for DWC 3.4.0 to be uploaded either on "Upload&Start", "System Files", or "Plugins -> External Plugins".
It registers a new tab under Settings -> Machine -> Endstops where the endstop states of each axis can be observed.

Input Shaping (beta1)

This plugin lets you tune input shaping. It lets you see estimated damping at given input frequencies and it allows you to record and evaluate different motion profiles.

Motion Webcam Server

This plugin runs the motion webcam streaming service as a DSF plugin. The main motion.conf file is accessible via 0:/sys/motion.conf (aka /opt/dsf/sd/sys/motion.conf).

Note that the default configuration uses the default /dev/video0 device node, which is generally applicable to external USB webcams. Depending on your choice of camera, extra customizations may be required.

Plugins for version v3.4-rc2

This release holds the following plugins:

Endstops Monitor

This is a simple demo plugin for DWC 3.4-rc2 to be uploaded either on "Upload&Start", "System Files", or "Plugins -> External Plugins".
It registers a new tab under Settings -> Machine -> Endstops where the endstop states of each axis can be observed.

Motion Webcam Server

This plugin runs the motion webcam streaming service as a DSF plugin. The main motion.conf file is accessible via 0:/sys/motion.conf.

Note that the default configuration uses the default /dev/video0 device node, which is generally applicable to external USB webcams. Depending on your choice of camera, extra customizations may be required.

Plugins for version v3.4-rc1

This release holds the following plugins:

Endstops Monitor

This is a simple demo plugin for DWC 3.4-rc1 to be uploaded either on "Upload&Start", "System Files", or "Plugins -> External Plugins".
It registers a new tab under Settings -> Machine -> Endstops where the endstop states of each axis can be observed.

Motion Webcam Server

This plugin runs the motion webcam streaming service as a DSF plugin. The main motion.conf file is accessible via 0:/sys/motion.conf.

Note that the default configuration uses the default /dev/video0 device node, which is generally applicable to external USB webcams. Depending on your choice of camera, extra customizations may be required.

Plugins for version 3.4-b7

This release holds the following plugins:

Endstops Monitor

This is a simple demo plugin for DWC 3.4-b6 to be uploaded either on "Upload&Start" or on "System Files".
It registers a new tab under Settings -> Machine -> Endstops where the endstop states of each axis can be observed.

Motion Webcam Server

This plugin runs the motion webcam streaming service as a DSF plugin. The main motion.conf file is accessible via 0:/sys/motion.conf.

Note that the default configuration uses the default /dev/video0 device node, which is generally applicable to external USB webcams. Depending on your choice of camera, extra customizations may be required.

Plugins for version v3.4-b6

This release holds the following plugins:

Endstops Monitor

This is a simple demo plugin for DWC 3.4-b6 to be uploaded either on "Upload&Start" or on "System Files".
It registers a new tab under Settings -> Machine -> Endstops where the endstop states of each axis can be observed.

Plugins for version v3.4-b2

This release holds the following plugins:

Endstops Monitor

This is a simple demo plugin for DWC 3.4-b2 to be uploaded either on "Upload&Start" or on "System Files".
It registers a new tab under Settings -> Machine -> Endstops where the endstop states of each axis can be observed.

Plugins for version v3.3.0

This release holds the following plugins:

Endstops Monitor

This is a simple demo plugin for DWC 3.3 to be uploaded either on "Upload&Start" or on "System Files".
It registers a new tab under Settings -> Machine -> Endstops where the endstop states of each axis can be observed.

Plugins for v3.3-b2

This release holds the following plugins:

Endstops Monitor

This is a simple demo plugin for DWC 3.3-b2 to be uploaded either on "Upload&Start" or on "System Files".
It registers a new tab under Settings -> Machine -> Endstops where the endstop states of each axis can be observed.