-
Notifications
You must be signed in to change notification settings - Fork 0
/
Copy pathrc.wireless.conf
226 lines (209 loc) · 7.18 KB
/
rc.wireless.conf
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
# Wireless LAN adapter configuration
#
# Theory of operation :
#
# The script attempts to match a block of settings to the specific wireless
# card inserted, the *first* block matching the card is used.
# The address format is "hwaddr", with * as a wildcard.
# 'hwaddr' is the unique MAC address identifier of the wireless card.
# The MAC address is usually printed on the card, or can be found via
# "/sbin/ip link show dev $interface"
# Some examples here use only half of the MAC address with a wildcard to
# match a whole family of cards...
#
# All the Wireless specific configuration is done through the Wireless
# Extensions, so we will just call 'iwconfig' with the right parameters
# defined below.
# Of course, you need to have iwconfig installled on your system.
# To download iwconfig, or for more info on Wireless Extensions :
# http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html
#
# Note : you don't need to fill all parameters, leave them blank, in most
# cases the driver will initialise itself with sane defaults values or
# automatically figure out the value... And no drivers do support all
# possible settings...
#
# -- This is a modified '/etc/pcmcia/wireless.opts' script --
# -- I added sections for Prism/GT and Atheros based cards --
# -- (supported by the prism54 and madwifi drivers) --
# -- 16/sep/2004 * Eric Hameleers --
#
VERBOSE=1
case "$HWADDR" in
## NOTE : Comment out the following five lines to activate the samples below ...
## --------- START SECTION TO REMOVE -----------
## Pick up any Access Point, should work on most 802.11 cards
*)
INFO="Any ESSID"
ESSID="any"
;;
## ---------- END SECTION TO REMOVE ------------
# Here are a few examples with a few Wireless LANs supported...
# The matching is done on the first 3 bytes of the MAC address
# SMC2835W EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Adapter
00:04:E2:*)
INFO="SMC2835W EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Adapter"
# ESSID (extended network name) : My Network, any
ESSID="any"
# NWID/Domain (cell identifier) : 89AB, 100, off
NWID=""
# Operation mode : Ad-Hoc, Managed, Master, Repeater, Secondary, auto
MODE="Managed"
# Frequency or channel : 1, 2, 3 (channel) ; 2.422G, 2.46G (frequency)
FREQ=""
CHANNEL="7"
# Sensitivity (cell size + roaming speed) : 1, 2, 3 ; -70 (dBm)
SENS=""
# Bit rate : auto, 1M, 11M,54M
RATE="auto"
# Encryption key : 4567-89AB-CD, s:password
# Example for 40-bit encryption:
#KEY="883e-aa67-21 [1] key 5501-d0da-87 [2] key 91f5-3368-6b [3] key 2d73-31b7-96 [4]"
# Example for 104-bit encryption (aka 128-bit WEP):
#KEY="d5ad2f05abd048ecf10b1c80c7"
KEY=""
# RTS threshold : off, 500
RTS=""
# Fragmentation threshold : off, 1000
FRAG=""
# Other iwconfig parameters : power off, ap 01:23:45:67:89:AB
IWCONFIG=""
# iwspy parameters : + 01:23:45:67:89:AB
IWSPY=""
# iwpriv parameters : set_port 2, set_histo 50 60
IWPRIV=""
;;
# Multiband Atheros based 802.11a/b/g universal NIC cards
00:05:4E:*)
INFO="Multiband Atheros based 802.11a/b/g universal NIC"
# ESSID (extended network name) : My Network, any
ESSID=""
# Operation mode : Ad-Hoc, Managed, Master, Repeater, Secondary, auto
MODE="Managed"
# Frequency or channel : 1, 2, 3 (channel) ; 2.422G, 2.46G (frequency)
FREQ=""
CHANNEL="7"
# Bit rate : auto, 1M, 11M,54M
RATE="auto"
# Encryption key : 4567-89AB-CD, s:password
# Example for 40-bit encryption:
#KEY="883e-aa67-21 [1] key 5501-d0da-87 [2] key 91f5-3368-6b [3] key 2d73-31b7-96 [4]"
# Example for 104-bit encryption (aka 128-bit WEP):
#KEY="d5ad2f05abd048ecf10b1c80c7"
KEY=""
# Other iwconfig parameters : power off, ap 01:23:45:67:89:AB
IWCONFIG=""
# iwspy parameters : + 01:23:45:67:89:AB
IWSPY=""
# iwpriv parameters : set_port 2, set_histo 50 60
IWPRIV=""
;;
# Lucent Wavelan IEEE (+ Orinoco, RoamAbout and ELSA)
# Note : wvlan_cs driver only, and version 1.0.4+ for encryption support
00:60:1D:*|00:02:2D:*)
INFO="Wavelan IEEE example (Lucent default settings)"
ESSID="Wavelan Network"
MODE="Managed"
#RATE="auto"
KEY="s:secu1"
# To set all four keys, use :
#KEY="s:secu1 [1] key s:secu2 [2] key s:secu3 [3] key s:secu4 [4] key [1]"
# For the RG 1000 Residential Gateway: The ESSID is the identifier on
# the unit, and the default key is the last 5 digits of the same.
#ESSID="084d70"
#KEY="s:84d70"
;;
# Cisco/Aironet 4800/3x0
# Note : MPL driver only (airo/airo_cs), version 1.3 or later
00:40:96:*|00:02:8A:*)
INFO="Cisco/Aironet example (Cisco default settings)"
ESSID="any"
# To set all four ESSID, use iwconfig v21 and the same trick as above
MODE="Managed"
#RATE="11M auto"
#KEY="d5ad2f05abd048ecf10b1c80c7"
KEY="off"
;;
# Samsung MagicLan (+ some other PrismII cards)
# Note : Samsung binary library driver, version 1.20 or later
00:00:F0:*|00:02:78:*)
INFO="Samsung MagicLan example (Samsung default settings)"
ESSID="any"
MODE="Managed"
CHANNEL="4"
RATE="auto"
#KEY="883e-aa67-21 [1] key 5501-d0da-87 [2] key 91f5-3368-6b [3] key 2d73-31b7-96 [4]"
#IWCONFIG="power on"
;;
# Raytheon Raylink/WebGear Aviator2.4
# Note : doesn't work yet, please use for debugging only :-(
00:00:8F:*|00:00:F1:*)
INFO="Raylink/Aviator2.4 example (Aviator default ad-hoc setting)"
ESSID="ADHOC_ESSID"
MODE="Ad-Hoc"
RATE="auto"
IWPRIV="set_framing 1"
;;
# Old Lucent Wavelan
08:00:0E:*)
INFO="Wavelan example (Lucent default settings)"
NWID="0100"
MODE="Ad-Hoc"
FREQ="2.425G"
KEY="off"
;;
# Netwave (Xircom Netwave/Netwave Airsurfer)
00:80:C7:*)
INFO="Netwave example (Netwave default settings)"
NWID="100"
KEY="00"
;;
# Proxim RangeLan2/Symphony (what is the MAC address ???)
XX:XX:XX:*)
INFO="Proxim RangeLan2/Symphony example"
NWID="0"
MODE="Master"
CHANNEL="15"
IWPRIV="setsubchan 1"
;;
# No Wires Needed Swallow 550 and 1100 setting (what is the MAC address ???)
XX:XX:XX:*)
INFO="NWN Swallow example"
ESSID="session"
KEY="0000-0000-00 open"
;;
# Symbol Spectrum24 setting (what is the MAC address ???)
XX:XX:XX:*)
INFO="Symbol Spectrum24 example"
ESSID="Essid string"
;;
# Generic example (decribe all possible settings)
*)
INFO="Fill with your own settings..."
# ESSID (extended network name) : My Network, any
ESSID=""
# NWID/Domain (cell identifier) : 89AB, 100, off
NWID=""
# Operation mode : Ad-Hoc, Managed, Master, Repeater, Secondary, auto
MODE=""
# Frequency or channel : 1, 2, 3 (channel) ; 2.422G, 2.46G (frequency)
FREQ=""
CHANNEL=""
# Sensitivity (cell size + roaming speed) : 1, 2, 3 ; -70 (dBm)
SENS=""
# Bit rate : auto, 1M, 11M
RATE=""
# Encryption key : 4567-89AB-CD, s:password
KEY=""
# RTS threshold : off, 500
RTS=""
# Fragmentation threshold : off, 1000
FRAG=""
# Other iwconfig parameters : power off, ap 01:23:45:67:89:AB
IWCONFIG=""
# iwspy parameters : + 01:23:45:67:89:AB
IWSPY=""
# iwpriv parameters : set_port 2, set_histo 50 60
IWPRIV=""
;;
esac