greaseweazle.h

#ifndef GREASEWEAZLE_H
#define GREASEWEAZLE_H

#include <stdint.h>

#define GREASEWEAZLE_VID 0x1209
#define GREASEWEAZLE_PID 0x4d69

#define GREASEWEAZLE_ID ((GREASEWEAZLE_VID << 16) | GREASEWEAZLE_PID)

#define EP_OUT 0x02
#define EP_IN 0x83

//extern Bytes fluxEngineToGreaseweazle(const Bytes& fldata, nanoseconds_t clock);
//extern Bytes greaseWeazleToFluxEngine(const Bytes& gwdata, nanoseconds_t clock);
//extern Bytes stripPartialRotation(const Bytes& fldata);

/* Copied from
 * https://github.com/keirf/Greaseweazle/blob/master/inc/cdc_acm_protocol.h.
 *
 * WARNING: these headers were originally defined with 'packed', which is a
 * gccism so it's been dummied out. Don't use them expecting wire protocol
 * structures. */

#define packed /* */

/*
 * GREASEWEAZLE COMMAND SET
 */

/* CMD_GET_INFO, length=3, idx. Returns 32 bytes after ACK. */
#define CMD_GET_INFO 0
/* [BOOTLOADER] CMD_UPDATE, length=6, <update_len>.
 * Host follows with <update_len> bytes.
 * Bootloader finally returns a status byte, 0 on success. */
/* [MAIN FIRMWARE] CMD_UPDATE, length=10, <update_len>, 0xdeafbee3.
 * Host follows with <update_len> bytes.
 * Main firmware finally returns a status byte, 0 on success. */
#define CMD_UPDATE 1
/* CMD_SEEK, length=3, cyl#. Seek to cyl# on selected drive. */
#define CMD_SEEK 2
/* CMD_HEAD, length=3, head# (0=bottom) */
#define CMD_HEAD 3
/* CMD_SET_PARAMS, length=3+nr, idx, <nr bytes> */
#define CMD_SET_PARAMS 4
/* CMD_GET_PARAMS, length=4, idx, nr_bytes. Returns nr_bytes after ACK. */
#define CMD_GET_PARAMS 5
/* CMD_MOTOR, length=4, drive#, on/off. Turn on/off a drive motor. */
#define CMD_MOTOR 6
/* CMD_READ_FLUX, length=2-8. Argument is gw_read_flux.
 * Returns flux readings until EOStream. */
#define CMD_READ_FLUX 7
/* CMD_WRITE_FLUX, length=2-4. Argument is gw_write_flux.
 * Host follows with flux readings until EOStream. */
#define CMD_WRITE_FLUX 8
/* CMD_GET_FLUX_STATUS, length=2. Last read/write status returned in ACK. */
#define CMD_GET_FLUX_STATUS 9
/* CMD_SWITCH_FW_MODE, length=3, <mode> */
#define CMD_SWITCH_FW_MODE 11
/* CMD_SELECT, length=3, drive#. Select drive# as current unit. */
#define CMD_SELECT 12
/* CMD_DESELECT, length=2. Deselect current unit (if any). */
#define CMD_DESELECT 13
/* CMD_SET_BUS_TYPE, length=3, bus_type. Set the bus type. */
#define CMD_SET_BUS_TYPE 14
/* CMD_SET_PIN, length=4, pin#, level. */
#define CMD_SET_PIN 15
/* CMD_RESET, length=2. Reset all state to initial (power on) values. */
#define CMD_RESET 16
/* CMD_ERASE_FLUX, length=6. Argument is gw_erase_flux. */
#define CMD_ERASE_FLUX 17
/* CMD_SOURCE_BYTES, length=6. Argument is gw_sink_source_bytes. */
#define CMD_SOURCE_BYTES 18
/* CMD_SINK_BYTES, length=6. Argument is gw_sink_source_bytes. */
#define CMD_SINK_BYTES 19
#define CMD_MAX 19

/*
 * CMD_SET_BUS CODES
 */
#define BUS_NONE 0
#define BUS_IBMPC 1
#define BUS_SHUGART 2
#define BUS_APPLE2 3

/*
 * ACK RETURN CODES
 */
#define ACK_OKAY 0
#define ACK_BAD_COMMAND 1
#define ACK_NO_INDEX 2
#define ACK_NO_TRK0 3
#define ACK_FLUX_OVERFLOW 4
#define ACK_FLUX_UNDERFLOW 5
#define ACK_WRPROT 6
#define ACK_NO_UNIT 7
#define ACK_NO_BUS 8
#define ACK_BAD_UNIT 9
#define ACK_BAD_PIN 10
#define ACK_BAD_CYLINDER 11

/*
 * CONTROL-CHANNEL COMMAND SET:
 * We abuse SET_LINE_CODING requests over endpoint 0, stashing a command
 * in the baud-rate field.
 */
#define BAUD_NORMAL 9600
#define BAUD_CLEAR_COMMS 10000

/*
 * Flux stream opcodes. Preceded by 0xFF byte.
 *
 * Argument types:
 *  N28: 28-bit non-negative integer N, encoded as 4 bytes b0,b1,b2,b3:
 *   b0 = (uint8_t)(1 | (N <<  1))
 *   b1 = (uint8_t)(1 | (N >>  6))
 *   b2 = (uint8_t)(1 | (N >> 13))
 *   b3 = (uint8_t)(1 | (N >> 20))
 */
/* FLUXOP_INDEX [CMD_READ_FLUX]
 *  Args:
 *   +4 [N28]: ticks to index, relative to sample cursor.
 *  Signals an index pulse in the read stream. Sample cursor is unaffected. */
#define FLUXOP_INDEX 1
/* FLUXOP_SPACE [CMD_READ_FLUX, CMD_WRITE_FLUX]
 *  Args:
 *   +4 [N28]: ticks to increment the sample cursor.
 *  Increments the sample cursor with no intervening flux transitions. */
#define FLUXOP_SPACE 2
/* FLUXOP_ASTABLE [CMD_WRITE_FLUX]
 *  Args:
 *   +4 [N28]: astable period.
 *  Generate regular flux transitions at specified astable period.
 *  Duration is specified by immediately preceding FLUXOP_SPACE opcode(s). */
#define FLUXOP_ASTABLE 3

/*
 * COMMAND PACKETS
 */

/* CMD_GET_INFO, index 0 */
#define GETINFO_FIRMWARE 0
struct packed gw_info
{
    uint8_t fw_major;
    uint8_t fw_minor;
    uint8_t is_main_firmware; /* == 0 -> update bootloader */
    uint8_t max_cmd;
    uint32_t sample_freq;
    uint8_t hw_model, hw_submodel;
    uint8_t usb_speed;
};
extern struct gw_info gw_info;

/* CMD_GET_INFO, index 1 */
#define GETINFO_BW_STATS 1
struct packed gw_bw_stats
{
    struct packed
    {
        uint32_t bytes;
        uint32_t usecs;
    } min_bw, max_bw;
};

/* CMD_READ_FLUX */
struct packed gw_read_flux
{
    /* Maximum ticks to read for (or 0, for no limit). */
    uint32_t ticks;
    /* Maximum index pulses to read (or 0, for no limit). */
    uint16_t max_index;
};

/* CMD_WRITE_FLUX */
struct packed gw_write_flux
{
    /* If non-zero, start the write at the index pulse. */
    uint8_t cue_at_index;
    /* If non-zero, terminate the write at the next index pulse. */
    uint8_t terminate_at_index;
};

/* CMD_ERASE_FLUX */
struct packed gw_erase_flux
{
    uint32_t ticks;
};

/* CMD_SINK_SOURCE_BYTES */
struct packed gw_sink_source_bytes
{
    uint32_t nr_bytes;
};

/* CMD_{GET,SET}_PARAMS, index 0 */
#define PARAMS_DELAYS 0
struct packed gw_delay
{
    uint16_t select_delay; /* usec */
    uint16_t step_delay;   /* usec */
    uint16_t seek_settle;  /* msec */
    uint16_t motor_delay;  /* msec */
    uint16_t auto_off;     /* msec */
};

/* CMD_SWITCH_FW_MODE */
#define FW_MODE_BOOTLOADER 0
#define FW_MODE_NORMAL 1

#endif