-
Notifications
You must be signed in to change notification settings - Fork 272
/
axi_multicut.sv
237 lines (214 loc) · 7.88 KB
/
axi_multicut.sv
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
// Copyright (c) 2014-2019 ETH Zurich, University of Bologna
//
// Copyright and related rights are licensed under the Solderpad Hardware
// License, Version 0.51 (the "License"); you may not use this file except in
// compliance with the License. You may obtain a copy of the License at
// http://solderpad.org/licenses/SHL-0.51. Unless required by applicable law
// or agreed to in writing, software, hardware and materials distributed under
// this License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR
// CONDITIONS OF ANY KIND, either express or implied. See the License for the
// specific language governing permissions and limitations under the License.
//
// Authors:
// - Wolfgang Roenninger <wroennin@iis.ee.ethz.ch>
// - Andreas Kurth <akurth@iis.ee.ethz.ch>
// - Fabian Schuiki <fschuiki@iis.ee.ethz.ch>
// - Stefan Mach <smach@iis.ee.ethz.ch>
// Multiple AXI4 cuts.
//
// These can be used to relax timing pressure on very long AXI busses.
module axi_multicut #(
parameter int unsigned NoCuts = 32'd1, // Number of cuts.
// AXI channel structs
parameter type aw_chan_t = logic,
parameter type w_chan_t = logic,
parameter type b_chan_t = logic,
parameter type ar_chan_t = logic,
parameter type r_chan_t = logic,
// AXI request & response structs
parameter type axi_req_t = logic,
parameter type axi_resp_t = logic
) (
input logic clk_i, // Clock
input logic rst_ni, // Asynchronous reset active low
// slave port
input axi_req_t slv_req_i,
output axi_resp_t slv_resp_o,
// master port
output axi_req_t mst_req_o,
input axi_resp_t mst_resp_i
);
if (NoCuts == '0) begin : gen_no_cut
// degenerate case, connect input to output
assign mst_req_o = slv_req_i;
assign slv_resp_o = mst_resp_i;
end else begin : gen_axi_cut
// instantiate all needed cuts
axi_req_t [NoCuts:0] cut_req;
axi_resp_t [NoCuts:0] cut_resp;
// connect slave to the lowest index
assign cut_req[0] = slv_req_i;
assign slv_resp_o = cut_resp[0];
// AXI cuts
for (genvar i = 0; i < NoCuts; i++) begin : gen_axi_cuts
axi_cut #(
.Bypass ( 1'b0 ),
.aw_chan_t ( aw_chan_t ),
.w_chan_t ( w_chan_t ),
.b_chan_t ( b_chan_t ),
.ar_chan_t ( ar_chan_t ),
.r_chan_t ( r_chan_t ),
.axi_req_t ( axi_req_t ),
.axi_resp_t ( axi_resp_t )
) i_cut (
.clk_i,
.rst_ni,
.slv_req_i ( cut_req[i] ),
.slv_resp_o ( cut_resp[i] ),
.mst_req_o ( cut_req[i+1] ),
.mst_resp_i ( cut_resp[i+1] )
);
end
// connect master to the highest index
assign mst_req_o = cut_req[NoCuts];
assign cut_resp[NoCuts] = mst_resp_i;
end
// Check the invariants
// pragma translate_off
`ifndef VERILATOR
initial begin
assert(NoCuts >= 0);
end
`endif
// pragma translate_on
endmodule
`include "axi/assign.svh"
`include "axi/typedef.svh"
// interface wrapper
module axi_multicut_intf #(
parameter int unsigned ADDR_WIDTH = 0, // The address width.
parameter int unsigned DATA_WIDTH = 0, // The data width.
parameter int unsigned ID_WIDTH = 0, // The ID width.
parameter int unsigned USER_WIDTH = 0, // The user data width.
parameter int unsigned NUM_CUTS = 0 // The number of cuts.
) (
input logic clk_i,
input logic rst_ni,
AXI_BUS.Slave in,
AXI_BUS.Master out
);
typedef logic [ID_WIDTH-1:0] id_t;
typedef logic [ADDR_WIDTH-1:0] addr_t;
typedef logic [DATA_WIDTH-1:0] data_t;
typedef logic [DATA_WIDTH/8-1:0] strb_t;
typedef logic [USER_WIDTH-1:0] user_t;
`AXI_TYPEDEF_AW_CHAN_T(aw_chan_t, addr_t, id_t, user_t)
`AXI_TYPEDEF_W_CHAN_T(w_chan_t, data_t, strb_t, user_t)
`AXI_TYPEDEF_B_CHAN_T(b_chan_t, id_t, user_t)
`AXI_TYPEDEF_AR_CHAN_T(ar_chan_t, addr_t, id_t, user_t)
`AXI_TYPEDEF_R_CHAN_T(r_chan_t, data_t, id_t, user_t)
`AXI_TYPEDEF_REQ_T(axi_req_t, aw_chan_t, w_chan_t, ar_chan_t)
`AXI_TYPEDEF_RESP_T(axi_resp_t, b_chan_t, r_chan_t)
axi_req_t slv_req, mst_req;
axi_resp_t slv_resp, mst_resp;
`AXI_ASSIGN_TO_REQ(slv_req, in)
`AXI_ASSIGN_FROM_RESP(in, slv_resp)
`AXI_ASSIGN_FROM_REQ(out, mst_req)
`AXI_ASSIGN_TO_RESP(mst_resp, out)
axi_multicut #(
.NoCuts ( NUM_CUTS ),
.aw_chan_t ( aw_chan_t ),
.w_chan_t ( w_chan_t ),
.b_chan_t ( b_chan_t ),
.ar_chan_t ( ar_chan_t ),
.r_chan_t ( r_chan_t ),
.axi_req_t ( axi_req_t ),
.axi_resp_t ( axi_resp_t )
) i_axi_multicut (
.clk_i,
.rst_ni,
.slv_req_i ( slv_req ),
.slv_resp_o ( slv_resp ),
.mst_req_o ( mst_req ),
.mst_resp_i ( mst_resp )
);
// Check the invariants.
// pragma translate_off
`ifndef VERILATOR
initial begin
assert (ADDR_WIDTH > 0) else $fatal(1, "Wrong addr width parameter");
assert (DATA_WIDTH > 0) else $fatal(1, "Wrong data width parameter");
assert (ID_WIDTH > 0) else $fatal(1, "Wrong id width parameter");
assert (USER_WIDTH > 0) else $fatal(1, "Wrong user width parameter");
assert (in.AXI_ADDR_WIDTH == ADDR_WIDTH) else $fatal(1, "Wrong interface definition");
assert (in.AXI_DATA_WIDTH == DATA_WIDTH) else $fatal(1, "Wrong interface definition");
assert (in.AXI_ID_WIDTH == ID_WIDTH) else $fatal(1, "Wrong interface definition");
assert (in.AXI_USER_WIDTH == USER_WIDTH) else $fatal(1, "Wrong interface definition");
assert (out.AXI_ADDR_WIDTH == ADDR_WIDTH) else $fatal(1, "Wrong interface definition");
assert (out.AXI_DATA_WIDTH == DATA_WIDTH) else $fatal(1, "Wrong interface definition");
assert (out.AXI_ID_WIDTH == ID_WIDTH) else $fatal(1, "Wrong interface definition");
assert (out.AXI_USER_WIDTH == USER_WIDTH) else $fatal(1, "Wrong interface definition");
end
`endif
// pragma translate_on
endmodule
module axi_lite_multicut_intf #(
// The address width.
parameter int unsigned ADDR_WIDTH = 0,
// The data width.
parameter int unsigned DATA_WIDTH = 0,
// The number of cuts.
parameter int unsigned NUM_CUTS = 0
) (
input logic clk_i ,
input logic rst_ni ,
AXI_LITE.Slave in ,
AXI_LITE.Master out
);
typedef logic [ADDR_WIDTH-1:0] addr_t;
typedef logic [DATA_WIDTH-1:0] data_t;
typedef logic [DATA_WIDTH/8-1:0] strb_t;
`AXI_LITE_TYPEDEF_AW_CHAN_T(aw_chan_t, addr_t)
`AXI_LITE_TYPEDEF_W_CHAN_T(w_chan_t, data_t, strb_t)
`AXI_LITE_TYPEDEF_B_CHAN_T(b_chan_t)
`AXI_LITE_TYPEDEF_AR_CHAN_T(ar_chan_t, addr_t)
`AXI_LITE_TYPEDEF_R_CHAN_T(r_chan_t, data_t)
`AXI_LITE_TYPEDEF_REQ_T(axi_req_t, aw_chan_t, w_chan_t, ar_chan_t)
`AXI_LITE_TYPEDEF_RESP_T(axi_resp_t, b_chan_t, r_chan_t)
axi_req_t slv_req, mst_req;
axi_resp_t slv_resp, mst_resp;
`AXI_LITE_ASSIGN_TO_REQ(slv_req, in)
`AXI_LITE_ASSIGN_FROM_RESP(in, slv_resp)
`AXI_LITE_ASSIGN_FROM_REQ(out, mst_req)
`AXI_LITE_ASSIGN_TO_RESP(mst_resp, out)
axi_multicut #(
.NoCuts ( NUM_CUTS ),
.aw_chan_t ( aw_chan_t ),
.w_chan_t ( w_chan_t ),
.b_chan_t ( b_chan_t ),
.ar_chan_t ( ar_chan_t ),
.r_chan_t ( r_chan_t ),
.axi_req_t ( axi_req_t ),
.axi_resp_t ( axi_resp_t )
) i_axi_multicut (
.clk_i,
.rst_ni,
.slv_req_i ( slv_req ),
.slv_resp_o ( slv_resp ),
.mst_req_o ( mst_req ),
.mst_resp_i ( mst_resp )
);
// Check the invariants.
// pragma translate_off
`ifndef VERILATOR
initial begin
assert (ADDR_WIDTH > 0) else $fatal(1, "Wrong addr width parameter");
assert (DATA_WIDTH > 0) else $fatal(1, "Wrong data width parameter");
assert (in.AXI_ADDR_WIDTH == ADDR_WIDTH) else $fatal(1, "Wrong interface definition");
assert (in.AXI_DATA_WIDTH == DATA_WIDTH) else $fatal(1, "Wrong interface definition");
assert (out.AXI_ADDR_WIDTH == ADDR_WIDTH) else $fatal(1, "Wrong interface definition");
assert (out.AXI_DATA_WIDTH == DATA_WIDTH) else $fatal(1, "Wrong interface definition");
end
`endif
// pragma translate_on
endmodule