diff --git a/source/_integrations/hwam.markdown b/source/_integrations/hwam.markdown
new file mode 100644
index 000000000000..1d098d89f96b
--- /dev/null
+++ b/source/_integrations/hwam.markdown
@@ -0,0 +1,108 @@
+---
+title: HWAM® SmartControl™
+description: Sensors, switches and buttons of HWAM® SmartControl™ wood burning stoves.
+ha_category:
+  - Climate
+  - Sensor
+  - Button
+  - Switch
+ha_iot_class: Local Polling
+ha_release: 2024.11
+ha_config_flow: true
+ha_codeowners:
+  - '@lordyavin'
+ha_domain: hwam
+ha_platforms:
+  - button
+  - select
+  - sensor
+  - switch
+ha_integration_type: integration
+---
+## Introduction
+
+The HWAM® SmartControl™ integration allows you to control and monitor your HWAM®
+wood-burning stove through Home Assistant, providing advanced climate control and
+efficient combustion management.
+
+HWAM® SmartControl™ is an electronic air control system developed in collaboration
+with DTU (Denmark's Technical University) to achieve the cleanest possible combustion.
+HWAM® SmartControl™ controls the whole process, whereby you automatically achieve the
+best possible combustion every time.
+
+HWAM® SmartControl™ stoves feature the following additional components compared to
+conventional stoves:
+
+- Airbox with 3 air valves and software.
+- Lambda probe that measures the oxygen level in the stove.
+- Temperature sensor that measures the temperature in the stove.
+- Room sensor tells the stove what temperature is in the room.
+
+All these components work together when the HWAM® SmartControl™ stove is in use
+and automatically ensure eco-friendly and efficient combustion. The only thing
+the user must do is to arrange some firewood and light the fire. HWAM® SmartControl™
+will take care of the rest.
+
+{% include integrations/config_flow.md %}
+
+## Entities
+
+The following controllable entities are available:
+
+### Button
+
+- **Start** (`start`) - The button to start the combustion.
+
+### Select
+
+- **Burn Level** (`burn_level`) - The burn level presets: 0-5
+
+#### Burn Levels
+
+- **Level 0** HWAM Smart Control runs at lowest
+possible combustion temperature to maintain correct combustion
+over the longest possible time, taking into account the room
+temperature.
+- **Level 1-4** At these levels, the system aims
+to achieve a constant room temperature. Therefore, once you
+have found the heat level that suits you best, do not turn the
+level up and down. At level 1-4, the system starts up gently
+until it finds the right level of flue gas temperature compared
+to the desired room temperature. For normal operation, levels
+2-3 are recommended.
+- **Level 5** Level 5 is a booster level intended only for situations
+where the stove needs to produce a lot of heat within a short
+period of time. The stove should NOT run at level 5 for a long
+period of time. NB! If level 5 is chosen, a lot of wood is needed
+to maintain correct combustion. Therefore, re-stoking alarms may
+sound even if there are still flames and unburned wood in the
+combustion chamber.
+
+### Sensor
+
+- **Oxygen Level** (%) (`oxygen_level`) - The level of oxygen in the combustion gases.
+- **Burning Phase** (`phase`) - The state/phase of the burning algorithm.
+- **Room Temperature** (°C) (`room_temperature`) - The room temperature as reported by the remote sensor.
+- **Stove Temperature** (°C) (`stove_temperature`) - The temperature within the combustion chamber. Aka the temperature of the fire.
+- **Valve 1-3 Position** (%) (`valve[1-3]_position`) - The positions of the air valves.
+
+### Switch
+
+- **Night Lowering** (`night_lowering`) - Enable or disable night lowering.
+  Adjustment of the start and end time for night lowering is yet not supported.
+  
+## Prerequisites
+
+You need a stove that is equipped with an Airbox that runs a compatible firmware
+which is connected to your local network. You should find the IP address via your
+routers list of network devices. Auto discovery is yet not supported.
+
+Tested firmware:
+
+- **fw version**  - 3.23.0
+- **wifi version** - 12.6.0
+
+## Automation Examples
+
+The most simple automation is to shut down all thermostats when the stove is started
+and to set them back to automatic when the stove goes into standby mode.