Don't have nuts

[hasecilu]

The STEMFIE system consists of several components as fasteners, shafts, gears, etc.

I think it's beneficial to have more components available on the workbench.

---

Beams

Straight

• U-shaped - https://www.stemfie.org/parts?view=article&id=126:u-shaped-symmetric&catid=46
• T-shaped - https://www.stemfie.org/parts?view=article&id=123:t-shaped-symmetric&catid=46
• L-shaped - also, we have general case for $90°<\alpha<180°$

Angled

• Square ended - https://www.stemfie.org/parts?view=article&id=125:square-ends&catid=26
• Box section - we have both cases - https://www.stemfie.org/parts?view=article&id=124:box-section&catid=26
• Threaded - https://www.stemfie.org/parts?view=article&id=128:threaded-ends&catid=26

Braces

Straight

• Slotted - Single end - https://www.stemfie.org/parts?view=article&id=136:slotted-single-end&catid=23
• Slotted - both ends - https://www.stemfie.org/parts?view=article&id=132:slotted-both-ends&catid=23
• Slotted - sequential - https://www.stemfie.org/parts?view=article&id=135:slotted-sequential&catid=23
• Slotted - centered - https://www.stemfie.org/parts?view=article&id=133:slotted-centered&catid=23
• Slotted - full length - https://www.stemfie.org/parts?view=article&id=134:slotted-full-length&catid=23

Angled

• 90° asymmetric - https://www.stemfie.org/parts?view=category&id=49

Connectors

https://www.stemfie.org/parts?view=article&id=138:beam-through-hole&catid=37

• 1 way
• 2 ways 90°
• 2 ways 180°
• 3 ways
• 4 ways

Fasteners

Nuts

Cam-locking

• Open - https://www.stemfie.org/parts?view=article&id=140:open&catid=62

Threaded

• Barrel through hole center - https://www.stemfie.org/parts?view=article&id=144:barrel-through-hole-center&catid=20
• Open - https://www.stemfie.org/parts?view=article&id=143:open&catid=20
• Barrel threaded center - https://www.stemfie.org/parts?view=article&id=141:barrel-threaded-center&catid=20
• Cap nuts - https://www.stemfie.org/parts?view=article&id=142:cap-nuts&catid=20

Pins

• Spring pins locating unidirectional - https://www.stemfie.org/parts?view=article&id=148:spring-pin-locating-unidirectional&catid=63
• Spring pin inner - https://www.stemfie.org/parts?view=article&id=147:spring-pin-inner&catid=63
• Cam locking - https://www.stemfie.org/parts?view=article&id=145:cam-locking&catid=63
• Spring pin locating bidirectional - https://www.stemfie.org/parts?view=article&id=146:spring-pin-locating-bidirectional&catid=63

Screws

• Fully threaded RHD- https://www.stemfie.org/parts?view=article&id=151:fully-threaded-rhd&catid=31
• Shoulder screws RHD - https://www.stemfie.org/parts?view=article&id=150:shoulder-screws-rhd&catid=31
• Fully threaded STEMFIE HEAD - https://www.stemfie.org/parts?view=article&id=194:fully-threaded-stemfie-head&catid=31

Spacers

• Fixed - https://www.stemfie.org/parts?view=article&id=152:fixed&catid=64
• Free - https://www.stemfie.org/parts?view=article&id=153:free&catid=64

Threaded rods

• Fully threaded - https://www.stemfie.org/parts?view=article&id=154:fully-threaded&catid=65

Washers

• Fixed - https://www.stemfie.org/parts?view=article&id=155:fixed&catid=66
• Free - https://www.stemfie.org/parts?view=article&id=156:free&catid=66

Plates

• Triangular plate - https://www.stemfie.org/parts?view=article&id=173:3-triangular&catid=68
• Square plate - in realy we hace rectangular plate - https://www.stemfie.org/parts?view=article&id=175:4-square&catid=68
• Hexagonal plate - https://www.stemfie.org/parts?view=article&id=171:6-hexagonal&catid=68

Shafts

• Plain - https://www.stemfie.org/parts?view=article&id=157:plain&catid=35

Springs

• Rotor - https://www.stemfie.org/parts?view=article&id=158:rotor&catid=67

Tools

• Driver Nut - https://www.stemfie.org/parts?view=article&id=161:driver-nut-spn-tol-0034&catid=40
• Driver Screw Nut - https://www.stemfie.org/parts?view=article&id=159:driver-screw-nut-spn-tol-0001&catid=40
• Driver Nut Screw RHD - https://www.stemfie.org/parts?view=article&id=181:spn-tol-0035&catid=40
• Spanner Nut - https://www.stemfie.org/parts?view=article&id=160:spanner-nut-spn-tol-0004&catid=40

[Stemfie3D]

I fully agree. The complete set of CAD files for adding new parts to the workbench can be fetched from get.stemfie.org.

[hasecilu]

If there is no response I could step as maintainer in my fork... ideally parts would be parametrically created, but for the time being could make a command to download from cloud, any help is appreciated.