-
Notifications
You must be signed in to change notification settings - Fork 0
/
printer-20240803_215744.cfg
92 lines (83 loc) · 2.13 KB
/
printer-20240803_215744.cfg
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
[include mainsail.cfg]
# Enable object exclusion
[exclude_object]
# Enable arcs support
[gcode_arcs]
resolution: 0.1
[include KAMP_Settings.cfg]
###########################
### MCU DEFINITIONS ###
###########################
[include config/mcu_definitions/host.cfg]
[include config/mcu_definitions/gbb15.cfg]
[include config/mcu_definitions/ebb36.cfg]
[include config/mcu_definitions/pico.cfg]
###########################
### HARDWARE COMPONENTS ###
###########################
#[include config/hardware/adxl.cfg]
[include config/hardware/extruder.cfg]
#[include config/hardware/fans.cfg]
[include config/hardware/heater_bed.cfg]
#[include config/hardware/lights.cfg]
[include config/hardware/probe/*.cfg]
#[include config/hardware/status_leds.cfg]
[include config/hardware/xy.cfg]
[include config/hardware/z.cfg]
#[include config/hardware/tones.cfg]
#[include config/hardware/display.cfg]
[include config/hardware/temperature_sensors/*.cfg]
[include config/corexy.cfg]
#####################
### MACROS FOLDER ###
#####################
[include macros/homing/*.cfg]
[include macros/base/*.cfg]
[include macros/probing/*.cfg]
[include macros/helpers/*.cfg]
#[include macros/calibration/*.cfg]
#[include macros/miscs/*.cfg]
#[include macros/monitoring/*.cfg]
#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*# -0.003472, 0.031944, 0.025000, 0.007986
#*# 0.010764, 0.015972, 0.025000, 0.020139
#*# 0.009722, 0.020139, 0.042361, 0.020833
#*# x_count = 4
#*# y_count = 3
#*# mesh_x_pps = 2
#*# mesh_y_pps = 2
#*# algo = lagrange
#*# tension = 0.2
#*# min_x = 40.0
#*# max_x = 133.99
#*# min_y = 53.0
#*# max_y = 127.0
#*#
#*# [probe]
#*# z_offset = 8.955
#*#
#*# [extruder]
#*# control = pid
#*# pid_kp = 22.683
#*# pid_ki = 2.749
#*# pid_kd = 46.785
#*#
#*# [heater_bed]
#*# control = pid
#*# pid_kp = 57.712
#*# pid_ki = 7.544
#*# pid_kd = 110.375
#*#
#*# [input_shaper]
#*# shaper_type_x = mzv
#*# shaper_freq_x = 86.4
#*# shaper_type_y = mzv
#*# shaper_freq_y = 65.2
#*#
#*# [stepper_z]
#*# position_endstop = -1.675