🐛 | GPIO documentation not up to date (usage of GPIO control) #1093

alexander-sterzer · 2020-10-16T11:40:52Z

Bug

Neither /RPi-Jukebox-RFID/scripts/gpio-buttons.py nor /RPi-Jukebox-RFID/misc/sampleconfigs/gpio-buttons.py.sample exists after using the one line installer --> GPIO Buttons cannot be integrated with Phoniebox.

What I did

Followed the instructions from https://github.com/MiczFlor/RPi-Jukebox-RFID/wiki/INSTALL-stretch to install the latest Raspian Buster/Phoniebox SW + Spotify. When asked about GPIO support I selected yes.

What happened

No GPIO scripts are available after installation. Both /RPi-Jukebox-RFID/misc/sampleconfigs/gpio-buttons.py.sample and /RPi-Jukebox-RFID/scripts/gpio-buttons.py are not available to configure GPIOs.

I expected this to happen

/RPi-Jukebox-RFID/scripts/gpio-buttons.py should be available after installation (as it was with previous installations).

Further information that might help

pi@raspberrypi:~ $ journalctl -u mopidy
-- Logs begin at Fri 2020-10-16 11:53:30 BST, end at Fri 2020-10-16 12:17:09 BST
-- No entries --

Software

Base image and version

Otherwise the output of cat /etc/os-release

PRETTY_NAME="Raspbian GNU/Linux 10 (buster)"
NAME="Raspbian GNU/Linux"
VERSION_ID="10"
VERSION="10 (buster)"
VERSION_CODENAME=buster
ID=raspbian
ID_LIKE=debian
HOME_URL="http://www.raspbian.org/"
SUPPORT_URL="http://www.raspbian.org/RaspbianForums"
BUG_REPORT_URL="http://www.raspbian.org/RaspbianBugs"

Branch / Release

master

Installscript

cd; rm buster-install-*; wget https://raw.githubusercontent.com/MiczFlor/RPi-Jukebox-RFID/master/scripts/installscripts/buster-install-default.sh; chmod +x buster-install-default.sh; ./buster-install-default.sh

Hardware

RaspberryPi version

3 B+

RFID Reader

16c0:27db HXGCoLtd Keyboard

Soundcard

Hifiberry Miniamp

Other notable hardware

GPIO settings not available

The text was updated successfully, but these errors were encountered:

s-martin · 2020-10-16T11:45:54Z

Since 2.0 these files are not used anymore, but GPIO control is used.

But as this isn't updated in the wiki yet, I consider this an documentation bug.

Thanks for the reminder ☺️

s-martin · 2020-10-18T09:07:11Z

I added some updates to the wiki:
https://github.com/MiczFlor/RPi-Jukebox-RFID/wiki/Using-GPIO-hardware-buttons

Dodo121188 · 2020-10-19T13:02:36Z

@s-martin can you give me the path, where i can change the pins of the buttons, please?

s-martin · 2020-10-19T19:07:31Z

Update the pins here:
~/RPi-Jukebox-RFID/settings/gpio_settings.ini

You can find more examples here:
https://github.com/MiczFlor/RPi-Jukebox-RFID/tree/develop/components/gpio_control/example_configs

Then restarting the service with sudo systemctl restart phoniebox-gpio-control will activate the new settings.

0x0lli · 2020-10-19T22:40:41Z

nothing works for me.
RPI 3B+ / buster-full / installscript 2.11 / miniamp / 0,96" OLED / RFID RC-522 all up and running
only the rotary encoder isn't. Its connected à la https://github.com/MiczFlor/RPi-Jukebox-RFID/wiki/Audio-RotaryKnobVolume without capacitors. I edited:

sudo nano /home/pi/RPi-Jukebox-RFID/components/gpio_control/gpio_control.py
config = configparser.ConfigParser(inline_comment_prefixes=";")
config_path = os.path.expanduser('home/pi/RPi-Jukebox-RFID/setting/gpio_settings.ini')
#tried the above line using a slash before home ( config_path = os.path.expanduser('/home/pi/RPi-Jukebox-RFID/setting/gpio_settings.ini') )

sudo nano /home/pi/RPi-Jukebox-RFID/settings/gpio_settings.ini
sudo nano /home/pi/RPi-Jukebox-RFID/.config/phoniebox/gpio_settings.ini
[DEFAULT]
enabled: True
[VolumeControl]
enabled: True
Type: RotaryEncoder
PinUp: 5
PinDown: 6
timeBase: 0.02
functionCallDown: functionCallVolD
functionCallUp: functionCallVolU
#everything else is commented in bash

sudo nano /home/pi/RPi-Jukebox-RFID/components/gpio_control/install.sh
if [[ ! -f ~/.config/phoniebox/gpio_settings.ini ]]; then
mkdir -p ~/.config/phoniebox && cp /home/pi/RPi-Jukebox-RFID/settings/gpio_settings.ini ~/.config/phoniebox/gpio_settings.ini

I edited this out of mere desperation.

Huseriato · 2020-10-20T05:55:23Z

I saw your comment on #1101: I'm currently documenting my setup. I'm not sure, if I did something special about it, but I used another wiring than in the documentation and created a new gpio_settings.ini from scratch.

First of all, I'm using DEBO ROT SWITCH from reichelt. I don't know, if this is a different version (it's from JoyIt).

This is my wiring:

Rotary Encoder	PIN Raspberry PI	Description
GND	Pin 14	Ground
VCC (+)	Pin 17	3.3V
DT	Pin 16	GPIO 23
CLK	Pin 32	GPIO 12

SW is unused. Theoretically this is pressing the button. But I think the press is nothing for the kids (they will rotate the knob, while pressing).

This is my VolumeControl section in the gpio_settings.ini:

[VolumeControl]
enabled: True
Type: RotaryEncoder
PinUp: 12
PinDown: 23
pull_up: True
hold_time: 0.3
timeBase: 0.1
functionCallUp: functionCallVolU
functionCallDown: functionCallVolD

If this does not work, you can consider scripting a little bit. Because you might see better, what's happening behind the scenes:
https://thepihut.com/blogs/raspberry-pi-tutorials/how-to-use-a-rotary-encoder-with-the-raspberry-pi (this is not the solution, but you can do this, to analyse the problem better).

Dodo121188 · 2020-10-20T08:36:51Z

@s-martin
thx for help!
if i change the "Vol.Change%" in settings to 5% and press the vol button, the volume goes 25% up, not 5%. Only if i set settings to 1% and in Editor "hold_time" to 0.1, the button turns the volume 5%. Is there another way to raise the volume to 5% per button when i set it ro 5% in settings,too?

s-martin · 2020-10-20T09:01:19Z

@0x0lli:
It's important that you edit the gpio_settings.ini file you reference in gpio_control.py.

I suggest you use /home/pi/RPi-Jukebox-RFID/settings/gpio_settings.ini (first slash is necessary)

What's the output of tail -n 500 /var/log/syslog?

0x0lli · 2020-10-20T15:32:01Z

@Huseriato @s-martin thanks for your help and patience!!!

after all, it was a cheap but oh-so-bitter-mistake that I made; apparently, I didnt copy-paste the directory information but wrote a part of it myself. an "s" was missing in .../setting/...
shame on me

alexander-sterzer · 2020-10-22T11:11:24Z

sudo systemctl

Update the pins here:
~/RPi-Jukebox-RFID/settings/gpio_settings.ini

You can find more examples here:
https://github.com/MiczFlor/RPi-Jukebox-RFID/tree/develop/components/gpio_control/example_configs

Then restarting the service with sudo systemctl restart phoniebox-gpio-control will activate the new settings.

I guess it would help many people to add the command how to restart the gpio service to the gpio wiki. I was doing many (time consuming) reboots when playing around with the gpio settings before finding this command.

themorlan · 2020-10-22T19:54:09Z

@s-martin I wrote updates to the wiki pages. How can I submit them to you ?

s-martin · 2020-10-22T19:56:26Z

@s-martin I wrote updates to the wiki pages. How can I submit them to you ?

Can't you just click Edit on the page? I don't know, if special permissions are required.

Otherwise just post them here in this issue, if you like.

themorlan · 2020-10-22T20:18:30Z

I did not want to deploy them before releasing 2.0 because they dont apply to current master version.

Control Jukebox with buttons / GPIO

Add buttons to your jukebox to control volume, skip tracks and more.

Before we start:
One of the plus points about this projects, at least in my mind,
was the fact that you don't need a soldering iron to build it.
Everything is USB, plug and play, thank you, boot and go.

Many, many fellow jukebox tweakers have contacted me to push
the envelope a bit further and add buttons to the jukebox.
Buttons to change the volume and skip between tracks in a playlist.

Enough said, here we go.

Pin numbering on the RPi

On your RPi there are pin numbers printed on the board. In the following we are not referring to the board numbers, but the Broadcom (BCM) pin numbering for the GPIO pins. You can find more information on this issue on the pin numbering section of the GPIO Zero documentation site.

Any pin marked “GPIO” in the diagram above can be used as a pin number. A button attached to “GPIO17” would be specified in the script as pin number 17 rather than 11 (which would be the count on the board).

Update September 2020

The service which provides the functionality of GPIO-Control-Devices has seen numerous changes in the past. The most recent version was originally designed by @veloxidSchweiz und @veloxid. It has now been integrated in the one-line installscript and support also RotaryEncoders in addition to normal buttons.

How to connect the buttons

In the default configuration the GPIO-control-service uses the new pinout for minimal interferance with other GPIO-Devices, which are fixed on some PINs.

Here is how to connect the buttons using the new pinout:

Volume Down GPIO6 (PIN35) and GND
Volume Up GPIO5 (PIN29) and GND
Play/Pause/Halt (or how you call it) GPIO27 (PIN13) and GND
Next GPIO23 (PIN16) and GND
Previous GPIO22 (PIN15) and GND
Shutdown (you need to hold button for 2 secs for shutdown) GPIO3 (PIN5) and GND

!!! IMPORTANT Only when using the above listed pins for wiring your shutdown pin you will be able to power-up the Raspberry PI from firmware halt. !!!

How to install the GPIO-Control-Service

When using the interactive version of the one-line installscript you will be asked if you want to activate the GPIO-Control-Service.
If you want to install the service outside the one-line installscript you need the command sudo bash /home/pi/RPi-Jukebox-RFID/components/gpio_control/install.sh

Where to find the configuration of the GPIO-Service

The configuration file can be found here: /home/pi/RPi-Jukebox-RFID/settings/gpio_settings.ini

Additional information:

Circuit example(s) for the button wiring

You will be using push buttons, which are essentially the same as arcade buttons, meaning: when you press them down, they are ON, when you let go, the are OFF. So skipping a track is tapping a button once, changing the volume, each tap changes it a bit. The updated GPIO from pullrequest #306 added the option to hold down the volume buttons and change every 0.3 seconds the volume according to the configured volume steps.

There are a number of different ways to connect a button. The easiest one is well explained on O'Reilly's RPi site:

Rotary knob for volume control (Drehknopf für Lautstärke)

Update September 2020

The service which provides the functionality of GPIO-Control-Devices has seen numerous changes in the past. The most recent version was originally designed by @veloxidSchweiz und @veloxid. It has now been integrated in the one-line installscript and support also RotaryEncoders in addition to normal buttons.

Originally taken from the Phoniebox@GitHub issues forum*
Tested with this rotary know hardware

To install the GPIO-Control-Service check the GPIO-Button-Section of the wiki

Circuit diagram

(capacitors are optionally)

Tested version: Used 3.3V Pin on Raspberry Pi. Connected everything without Capacitors.

  .---------------.                      .---------------.
  |               |                      |               |
  |           CLK |----------------------| GPIO 5        |
  |               |                      |               |
  |           DT  |----------------------| GPIO 6        |
  |               |                      |               |
  |           SW  |                      |               |
  |               |                      |               |
  |           +   |----------------------| 3.3V          |
  |               |                      |               |
  |           GND |----------------------| GND           |
  |               |                      |               |
  '---------------'                      '---------------'
       KY-040                                Raspberry

Once you've got the hardware done, edit /home/pi/RPi-Jukebox-RFID/settings/gpio_settings.ini and change:

[VolumeControl]
enabled: True
Type: TwoButtonControl ;or RotaryEncoder

to

[VolumeControl]
enabled: True
Type: RotaryEncoder

After that restart the GPIO-Service: sudo systemctl restart phoniebox-gpio-control.service

Huseriato · 2020-10-23T08:23:51Z

Volume Down GPIO6 (PIN35) and GND

GPIO6 is Pin 31.
PIN35 is GPIO19

So something is wrong here. Thank your for documentation. I prefer not to use PIN35, because it's reserved by HifiBerry Boards (Sound interface): https://www.hifiberry.com/docs/hardware/gpio-usage-of-hifiberry-boards/

s-martin · 2020-10-23T09:01:24Z

@Huseriato good catch

s-martin · 2020-11-29T19:20:26Z

Updated the wiki and users report it works, so close this here.

Please feel free to reopen the issue, if you still experience problems.

alexander-sterzer added the bug label Oct 16, 2020

s-martin added this to the 2.2 milestone Oct 16, 2020

s-martin added the documentation label Oct 16, 2020

s-martin changed the title ~~🐛 | GPIO scripts missing after installation~~ 🐛 | GPIO documentation not up to date (usage of GPIO control) Oct 16, 2020

0x0lli mentioned this issue Oct 19, 2020

🚀 Call a command before something is played and when playing stops #1101

Open

s-martin modified the milestones: 2.2, 2.3 Nov 23, 2020

s-martin closed this as completed Nov 29, 2020

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

🐛 | GPIO documentation not up to date (usage of GPIO control) #1093

🐛 | GPIO documentation not up to date (usage of GPIO control) #1093

alexander-sterzer commented Oct 16, 2020

s-martin commented Oct 16, 2020

s-martin commented Oct 18, 2020

Dodo121188 commented Oct 19, 2020

s-martin commented Oct 19, 2020

0x0lli commented Oct 19, 2020 •

edited

Loading

Huseriato commented Oct 20, 2020 •

edited

Loading

Dodo121188 commented Oct 20, 2020

s-martin commented Oct 20, 2020

0x0lli commented Oct 20, 2020

alexander-sterzer commented Oct 22, 2020

themorlan commented Oct 22, 2020

s-martin commented Oct 22, 2020

themorlan commented Oct 22, 2020

Huseriato commented Oct 23, 2020

s-martin commented Oct 23, 2020

s-martin commented Nov 29, 2020

🐛 | GPIO documentation not up to date (usage of GPIO control) #1093

🐛 | GPIO documentation not up to date (usage of GPIO control) #1093

Comments

alexander-sterzer commented Oct 16, 2020

Bug

What I did

What happened

I expected this to happen

Further information that might help

Software

Base image and version

Branch / Release

Installscript

Hardware

RaspberryPi version

RFID Reader

Soundcard

Other notable hardware

s-martin commented Oct 16, 2020

s-martin commented Oct 18, 2020

Dodo121188 commented Oct 19, 2020

s-martin commented Oct 19, 2020

0x0lli commented Oct 19, 2020 • edited Loading

Huseriato commented Oct 20, 2020 • edited Loading

Dodo121188 commented Oct 20, 2020

s-martin commented Oct 20, 2020

0x0lli commented Oct 20, 2020

@Huseriato @s-martin thanks for your help and patience!!!

alexander-sterzer commented Oct 22, 2020

themorlan commented Oct 22, 2020

s-martin commented Oct 22, 2020

themorlan commented Oct 22, 2020

Control Jukebox with buttons / GPIO

Pin numbering on the RPi

Update September 2020

How to connect the buttons

How to install the GPIO-Control-Service

Where to find the configuration of the GPIO-Service

Additional information:

Circuit example(s) for the button wiring

Rotary knob for volume control (Drehknopf für Lautstärke)

Update September 2020

Circuit diagram

Huseriato commented Oct 23, 2020

s-martin commented Oct 23, 2020

s-martin commented Nov 29, 2020

0x0lli commented Oct 19, 2020 •

edited

Loading

Huseriato commented Oct 20, 2020 •

edited

Loading