lock_321_notrun.yaml

substitutions:
  device_name: test-lock32
  entity_name: test_lock32
  friendly_name: test lock32
  device_name_wifi: testlock32
#========================================================================================================================

#pinout_mapping ESP32
  i2c_sda_pin:                GPIO21            # Пин sda для работы с шиной I2C магнитного энкодера AS560 
  i2c_scl_pin:                GPIO22            # Пин scl для работы с шиной I2C магнитного энкодера AS560
  as5600_dir_pin:             GPIO23            # Пин dir магнитного энкодера AS5600 
 
  a4988_step_pin:             GPIO14            # Пин step драйвера шагового двигателя a4988 (TMC2209 V3.0)
  a4988_dir_pin:              GPIO27            # Пин dir  драйвера  шагового двигателя a4988 (TMC2209 V3.0)
  a4988_sleep_pin:            GPIO4             # Пин sleep драйвера шагового двигателя a4988 (TMC2209 V3.0)
  grow_sensing_pin:           GPIO18            # пин wakeup сканера отпечатков  
  door_pos_pin:               GPIO32            # пин датчика (геркона) положения двери открыто/закрыто
  key_out_pin:                GPIO33            # пин сенсорной кнопки открытия замка
  dfplayer_tx_pin:            GPIO17            # пин RX DF-плеера
  dfplayer_rx_pin:            GPIO16            # пин TX DF-плеера
  finger_grow_tx_pin:         GPIO1             # пин RX сканера отпечатков
  finger_grow_rx_pin:         GPIO3             # пин TX сканера отпечатков
#========================================================================================================================
uart:
  - id: player
    tx_pin: $dfplayer_tx_pin                    # пин RX DF-плеера
    rx_pin: $dfplayer_rx_pin:                   # пин TX DF-плеера
    baud_rate: 9600
  - id: finger_grow 
    tx_pin: $finger_grow_tx_pin                 # пин RX сканера отпечатков
    rx_pin: $finger_grow_rx_pin                 # пин TX сканера отпечатков
    baud_rate: 57600
#======================================================================================================================== 
esphome:
  name: ${device_name}
  name_add_mac_suffix: false

esp32:
  board: esp32dev
  framework:
    type: esp-idf
    version: recommended

logger:

api:
  reboot_timeout: 50min
  #encryption:
   # key: !secret api_password
#===============================================================================  
  actions:
    - action: dfplayer_play_mp3
      variables:
        file: int
      then:
        - dfplayer.play_mp3:
            file: !lambda 'return file;'
    - action: dfplayer_set_volume
      variables:
        volume: int
      then:
        - dfplayer.set_volume: !lambda 'return volume;'
    - action: dfplayer_set_eq
      variables:
        preset: int
      then:
        - dfplayer.set_eq: !lambda 'return static_cast<dfplayer::EqPreset>(preset);'
    - action: dfplayer_reset
      then:
        - dfplayer.reset
    - action: dfplayer_volume_up
      then:
        - dfplayer.volume_up

    - action: dfplayer_volume_down
      then:
        - dfplayer.volume_down
#=============================================================================== 
# API for fingerprint GROW
    - action: enroll
      variables:
        finger_id: int
        num_scans: int
      then:
        - dfplayer.play_mp3:
            file: 5
        - delay: 3s   
        - dfplayer.play_mp3:
            file: 3
        - fingerprint_grow.enroll:
            finger_id: !lambda 'return finger_id;'
            num_scans: !lambda 'return num_scans;'
    - action: cancel_enroll
      then:
        - fingerprint_grow.cancel_enroll:
    - action: delete
      variables:
        finger_id: int
      then:
        - fingerprint_grow.delete:
            finger_id: !lambda 'return finger_id;'
    - action: delete_all
      then:
        - fingerprint_grow.delete_all:

ota:
  platform: esphome
  password: !secret ota_password

safe_mode:
  reboot_timeout: 50min

wifi:
  ssid: !secret wifi_ssid
  password: !secret wifi_password
  fast_connect: on
  reboot_timeout: 50min
  ap:
    ssid: ${device_name_wifi}
    #password: !secret wifi_ap_password

#========================================================================================================================
i2c:
  sda: $i2c_sda_pin
  scl: $i2c_scl_pin
  scan: true
  id: bus_a

as5600:
    id: my_as5600
    dir_pin: $as5600_dir_pin
    start_position: 0deg
    range: 360deg


globals:
  - id: full_cycle
    type: int
    restore_value: yes
    initial_value: '0'

  - id: prev_angle
    type: int
    restore_value: yes
    initial_value: '0'

  - id: press_button_out
    type: bool
    restore_value: no
    initial_value: 'false'

button:
  - platform: template
    name: "Full Cycle Reset"
    id: full_cycle_reset
    on_press:
      - lambda: |-
          id(full_cycle) = 0;

#=============================================================================== 
captive_portal:
stepper:
  - platform: a4988
    id: my_stepper
    step_pin: 
      number: $a4988_step_pin
#      ignore_strapping_warning: true
    dir_pin:
      number: $a4988_dir_pin
      inverted: true
      allow_other_uses: true
    sleep_pin:
      number: $a4988_sleep_pin
      inverted: true
#      ignore_strapping_warning: true
    max_speed: 2550 steps/s
number:
  - platform: template
    name: Position stepper
    optimistic: true
    min_value: 0
    id: number_pos
    max_value: 9000
    step: 0.5
    set_action:
      then:
        - stepper.set_target:
            id: my_stepper
            target: !lambda return x;            


#=============================================================================== 
time: # Время берем из Home Assistant
  - platform: homeassistant
    id: homeassistant_time
#===============================================================================

#=============================================================================== 
# DFPLAYER
#=============================================================================== 
dfplayer:
  uart_id: player
  id: player_lock
  # on_finished_playback:
  #   then:
  #     logger.log: 'Somebody press play!'
#===============================================================================
# FINGER GROW
#===============================================================================

fingerprint_grow:
  sensing_pin: 
    number: $grow_sensing_pin
    allow_other_uses: true
  uart_id: finger_grow 
  on_finger_scan_matched: # палец распознан
    - fingerprint_grow.aura_led_control:
        state: FLASHING
        speed: 25
        color: GREEN
        count: 5 
    - delay: 1s    
    - lock.unlock: Gimdow #открываем замок
    - delay: 1s
    - text_sensor.template.publish:
       id: fingerprint_state
       state: !lambda 'return "Finger " + to_string(finger_id) + ", confidence " + to_string(confidence);'
    - if:
        condition:
          lambda: 'return confidence > 50;'
        then:
          - homeassistant.tag_scanned: !lambda |-
              switch (finger_id) {
                case 0:
                  return "Person 1";
                case 1:
                  return "Person 2";
                default:
                  return "person_unknown";
              }
    - binary_sensor.template.publish: # включаем сеснор о правильном распозновании
        id: success_scanned
        state: ON
#    - delay: 2s
    - script.execute: breathing_light
  on_finger_scan_unmatched: # палец не распознан
    - text_sensor.template.publish:
        id: fingerprint_state
        state: "Unauthorized finger"
    # - dfplayer.play_mp3:
    #     file: 2         
    - fingerprint_grow.aura_led_control:
        state: FLASHING
        speed: 25
        color: RED
        count: 5
    - delay: 1s
    - script.execute: breathing_light
  on_enrollment_scan: # запись пальца в память
    - text_sensor.template.publish:
        id: fingerprint_state
        state: "Finger scanned"
    - fingerprint_grow.aura_led_control:
        state: FLASHING
        speed: 25
        color: Green
        count: 3
    - fingerprint_grow.aura_led_control:
        state: ALWAYS_ON
        speed: 0
        color: PURPLE
        count: 0
    - if:        
        condition:
          lambda: 'return scan_num < 5;'
        then:    
          - dfplayer.play_mp3:
              file: 7             
  on_enrollment_done: # запись пальца прошла успешно
    - text_sensor.template.publish:
        id: fingerprint_state
        state: "Enrolled fingerprint"
    - dfplayer.play_mp3:
        file: 4          
    - fingerprint_grow.aura_led_control:
          state: FLASHING
          speed: 15
          color: GREEN
          count: 3
    - delay: 2s
    - script.execute: breathing_light
  on_enrollment_failed: # неудачная запись пальца
    - text_sensor.template.publish:
        id: fingerprint_state
        state: "Failed to enroll fingerprint"
    - fingerprint_grow.aura_led_control:
        state: FLASHING
        speed: 25
        color: RED
        count: 4
    - dfplayer.play_mp3:
        file: 6           
    - delay: 2s
    - script.execute: breathing_light

#===============================================================================
# SENSOR
#===============================================================================
#-------------------------------------------------------------------------------
# Optional template text sensor for visual feedback
text_sensor:
  - platform: template
    id: fingerprint_state
    name: "Fingerprint State"

#-------------------------------------------------------------------------------

sensor:
  - platform: uptime # Время работы после последней перезагрузки
    name: "uptime_${device_name}"

#===============================================================================

  - platform: as5600 
    update_interval: 100ms 
    name: Angle 
    id: angle
    unit_of_measurement: ° 
    accuracy_decimals: 0
    icon: mdi:rotate-right 
    out_of_range_mode: nan 
    filters: 
      - delta: 1 
      - lambda:  
          uint16_t deg = (uint16_t)floor(x * as5600::RAW_TO_DEGREES * id(my_as5600).get_range_scale()); 
          return deg % 360;
    on_value:
      then:
        - lambda: |-
            if (((id(prev_angle) > 310 && x < 50) || (id(prev_angle) < x)) && !(id(prev_angle) < 50 && x > 310))
              id(full_cycle) += (id(prev_angle) > x ? 359 - id(prev_angle) + x : x - id(prev_angle));
            else if ((id(prev_angle) < 50 && x > 310) || (id(prev_angle) > x))
              id(full_cycle) -= (id(prev_angle) < x ? 359 - x + id(prev_angle) : id(prev_angle) - x);
            id(prev_angle) = x;

  - platform: template
    update_interval: 100ms
    name: "Full cycle"
    lambda: |-
      return id(full_cycle);

  - platform: template
    update_interval: 100ms
    name: "Position MAP"
    id: position_map
    lambda: |-
      return 9000 - min(9000, max(0, (int)remap(id(full_cycle), 0, 2018, 0, 9000)));

#===============================================================================    
         
  - platform: as5600
    update_interval: 100ms
    name: Position
    filters:
      - delta: 1
    raw_position:
      name: Raw Position
      filters:
        - delta: 1
    gain:
      name: Gain
      filters:
        - delta: 1
    magnitude:
      name: Magnitude
      filters:
        - delta: 1
    status:
      name: Status
      filters:
        - delta: 1

#===============================================================================    

binary_sensor:            
# ----------------------------  
# sensors fingerprint  
  - platform: fingerprint_grow
    id: fingerprint_enrolling
    name: "Fingerprint Enrolling"
    on_state:
      then:
        - fingerprint_grow.aura_led_control:
            state: ALWAYS_ON
            speed: 0
            color: PURPLE
            count: 0
# ----------------------------  
  - platform: template # сенсор удачного распознавания пальца
    name: success_scanned
    id: success_scanned
    icon: mdi:line-scan
    on_state:
      then:
        - delay: 5 s
        - binary_sensor.template.publish:
            id: success_scanned
            state: OFF
  # - platform: template # звонок
  #   name: zvonok
  #   id: zvonok
  #   icon: mdi:bell-ring
  #   on_state:
  #     then:
  #       - delay: 5 s
  #       - binary_sensor.template.publish:
  #           id: zvonok
  #           state: OFF
 
  - platform: status
    name: "${device_name}_status"

  - platform: gpio # сенсор прикосновения к сканеру
    filters:
      - delayed_on: 10ms
      - invert:
    pin: 
      number: $grow_sensing_pin
      allow_other_uses: true
    id: Finger_touch
    name: "Finger touch"
    icon: mdi:gesture-tap
    on_press:
      then:
        - if:  # включаем звонок
            condition:
              - binary_sensor.is_off: fingerprint_enrolling
            then:
              - fingerprint_grow.aura_led_control:
                  state: ALWAYS_ON
                  speed: 0
                  color: YELLOW
                  count: 0
    on_release:
      then:
        - script.execute: breathing_light
 
  - platform: gpio # геркон закрытия двери
    name: "Door sensor"
    id: Door_sensor
    device_class: door
    filters:
      - delayed_on: 200ms
      - delayed_off: 500ms
    pin:
      number: $door_pos_pin
      mode: INPUT_PULLUP
    on_state: 
      then:
        - script.execute: breathing_light 
        - if:
            condition:
              and: 
                - binary_sensor.is_off: Door_sensor
                - lambda: 'return id(press_button_out);'
            then:
              - delay: 0.5s
              - lock.lock: Gimdow #закрываем замок
              - delay: 0.5s
              - globals.set:
                  id: press_button_out
                  value: "false"
# ------------------
  # - platform: gpio
  #   pin: 
  #     number: GPIO27
  #     mode:
  #       input: true
  #       pulldown: true 
  #       pullup: True   
  #   id: button_out
  #   name: "button_out"
  #   filters:
  #     - delayed_on: 200ms         
    # on_state:
    #   then:
    #     - if:
    #         condition:
    #           - binary_sensor.is_on: button_out
    #         then:
    #           - script.execute: locking_door_button
    #           - dfplayer.play_mp3:
    #               file: 8                              
  - platform: gpio
    pin: 
      number: $key_out_pin
      allow_other_uses: true
      mode:
        input: true
        pulldown: true      
    id: button_out_light
    name: "button_out_light"
    filters:
      - delayed_on: 200ms      
    on_state:
      then:
        - if:
            condition:
              - binary_sensor.is_on: button_out_light
            then:  
              - script.execute: locking_door_button
              - dfplayer.play_mp3:
                  file: 8 
  # - platform: gpio
  #   pin: 
  #     number: GPIO27
  #     mode:
  #       input: true
  #       pulldown: true 
  #       pullup: True   
  #   id: button_out
  #   name: "button_out"
  #   filters:
  #     - delayed_on: 200ms         
    # on_state:
    #   then:
    #     - if:
    #         condition:
    #           - binary_sensor.is_on: button_out
    #         then:
    #           - script.execute: locking_door_button
    #           - dfplayer.play_mp3:
    #               file: 8                              
  #- platform: gpio
  #  pin: 
  #    number: GPIO12
  #    allow_other_uses: true
  #    mode:
  #      input: true
  #      pulldown: true      
  #  id: button_out_light_new
  #  name: "button_out_light_new"
  #  filters:
  #    - delayed_on: 200ms      
  #  on_state:
  #    then:
  #      - if:
  #          condition:
  #            - binary_sensor.is_on: button_out_light_new
  #          then:  
  #            - script.execute: locking_door_button
  #            - dfplayer.play_mp3:
  #                file: 8 

  #- platform: gpio # вход бинарного датчика открытия замка
  #  id: Lock_sensor
  #  name: "Lock sensor"
  #  filters:
  #    - delayed_on: 200ms
  #  pin:
  #    number: 33
  #    mode: INPUT_PULLUP
  #    allow_other_uses: true
  #  on_state: 
  #    then:
  #      - script.execute: breathing_light_zamok
# ----------------------------    
#===============================================================================
lock:
  - platform: template
    name: Lock
    optimistic: true
    lambda: |-
      if (id(position_map).state < 1)
      {
        return LOCK_STATE_UNLOCKED;
      } 
      else
      {
        return LOCK_STATE_LOCKED;
      }
    lock_action:
      - stepper.report_position:
          id: my_stepper
          position: !lambda |-
            return id(position_map).state;
      - stepper.set_target:
          id: my_stepper
          target: 9000
    unlock_action:
      - stepper.report_position:
          id: my_stepper
          position: !lambda |-
            return id(position_map).state;
      - stepper.set_target:
          id: my_stepper
          target: 0

# lock: # кнопки открытия/закрытия Gimdow с датчиком замка двери из ХА
  - platform: template
    name: Gimdow
    id: Gimdow
    optimistic: true
    assumed_state: false
    lock_action:
      - switch.turn_on: gate
      - delay: 300ms
      - switch.turn_off: gate
    unlock_action:
      - switch.turn_on: gate
      - delay: 200ms
      - switch.turn_off: gate
      - delay: 100ms
      - switch.turn_on: gate
      - delay: 200ms
      - switch.turn_off: gate
    lambda: |-
      if (id(Lock_sensor).state) {
        return LOCK_STATE_UNLOCKED;
      } else {
        return LOCK_STATE_LOCKED;
      }
#===============================================================================
# SCRIPT
#===============================================================================
script: #режим светодиода в зависимости от замка двери для возвращения значения после операций
  - id: breathing_light
    mode: restart
    then:
      - if:
          condition:
            - binary_sensor.is_off: Lock_sensor
          then:
            - fingerprint_grow.aura_led_control:
                state: BREATHING
                speed: 255
                color: BLUE
                count: 0
      - if:
          condition:
            and:
              - binary_sensor.is_on: Lock_sensor
              - binary_sensor.is_off: Door_sensor
          then:
            - fingerprint_grow.aura_led_control:
                state: BREATHING
                speed: 255
                color: GREEN
                count: 0
      - if:
          condition:
            - binary_sensor.is_on: Door_sensor
          then:
            - fingerprint_grow.aura_led_control:
                state: BREATHING
                speed: 255
                color: WHITE
                count: 0

#действие после нажатия кнопки на панели
  - id: locking_door_button
    mode: restart
    then:
      - globals.set:
          id: press_button_out
          value: "true"
      - if:
          condition:
            - binary_sensor.is_off: Lock_sensor
          then:
            - lock.unlock: Gimdow #открываем замок
            - delay: 1s
      - if:
          condition:
            and:
              - binary_sensor.is_on: Lock_sensor
              - binary_sensor.is_off: Door_sensor
          then:
            - lock.lock: Gimdow #закрываем замок 
            - delay: 0.5s          
      - wait_until:
          condition:
            not:
              - lambda: 'return id(press_button_out);'
          timeout: 5min              
      - if: 
          condition:
            and:
                - lambda: 'return id(press_button_out);'
                - binary_sensor.is_off: Door_sensor
          then:  
            - lock.lock: Gimdow #закрываем замок
            - delay: 0.5s
            - globals.set:
                id: press_button_out
                value: "false"

  - id: breathing_light_zamok #режим светодиода в зависимости от замка двери только для самого замка
    then:
      if:
        condition:
          - binary_sensor.is_off: Lock_sensor
        then:
          - fingerprint_grow.aura_led_control:
              state: FLASHING
              speed: 35
              color: GREEN
              count: 1
          - fingerprint_grow.aura_led_control:
              state: BREATHING
              speed: 255
              color: CYAN
              count: 0
        else:
          - fingerprint_grow.aura_led_control:
              state: FLASHING
              speed: 35
              color: GREEN
              count: 1
          - fingerprint_grow.aura_led_control:
              state: BREATHING
              speed: 85
              color: CYAN
              count: 0

#switch: # выход на управление брелком замка  
#  - platform: gpio
#    pin: GPIO27
#   inverted: true
#   id: gate  
#    name: "Switch gate close"