如果直接编译卡进度条常亮可尝试将906-bcm-ns-uart1.patch或906-BCM5301x-uart1.patch（根据内核版本选择）下载到target/linux/bcm53xx/patches-内核版本/

编译K3的屏幕控制组件

使用OpenWrt Snapshot源码编译lwz322/k3screenctrl使用的编译文件，在这里添加了luci-app-k3screenctrl的config文件/file/k3screenctrl，具体的介绍可以参考上面的链接

k3screenctrl_build

build k3screenctrl via OpenWrt Snapshot source and support luci-app-k3screenctrl

考察K3的DENPENDS

看了文档和官方的./targe/linux/image/Makefile以及coolsnowwolf/lede下的提交记录，官方文档有对DEPENDS的说明

Dependency Types

Various types of dependencies can be specified, which require a bit of explanation for their differences. More documentation is available at Using Dependencies

+	Package will depend on package and will select it when selected.
	Package will depend on package and will be invisible until is selected.
@FOO	Package depends on the config symbol CONFIG_FOO and will be invisible unless CONFIG_FOO is set. This usually used for depending on certain Linux versions or targets, e.g. @TARGET_foo will make a package only available for target foo. You can also use boolean expressions for complex dependencies, e.g. @(!TARGET_foo&&!TARGET_bar) will make the package unavailable for foo and bar.
+FOO:	Package will depend on if CONFIG_FOO is set, and will select when it is selected itself. The typical use case would be if there compile time options for this package toggling features that depend on external libraries. Note that the + replaces the @. There is limited support for boolean operators here compared to the @ type above. Negation ! is only supported to negate the whole condition. Parentheses are ignored, so use them only for readability. Like C, && has a higher precedence than ||. So +(YYY||FOO&&BAR):package will select package if CONFIG_YYY is set or if both CONFIG_FOO and CONFIG_BAR are set.
@FOO:	Package will depend on if CONFIG_FOO is set, and will be invisible until is selected when CONFIG_FOO is set.

Some typical config symbols for (conditional) dependencies are:

TARGET_	Target is selected
TARGET__	If the target has subtargets, subtarget is selected. If not, profile is selected. This is in addition to TARGET_
TARGET_	Target with subtarget and profile is selected.
LINUX_3_X	Linux version used is 3.x.*
LINUX_2_6_X	Linux version used is 2.6.x.* (:1: only used for backfire and earlier)
LINUX_2_4	Linux version is 2.4 ( only used in backfire and earlier, and only for target brcm-2.4)
USE_UCLIBC, USE_GLIBC, USE_EGLIBC	To (not) depend on a certain libc.
BROKEN	Package doesn't build or work, and should only be visible if “Show broken targets/packages” is selected. Prevents the package from failing builds by accidentally selecting it.
IPV6	IPv6 support in packages is selected.

Note that the syntax above applies to the DEPENDS field only.

用官方代码的master，19.07.4，19.07.3，以及coolsnowwolf/lede测试了下

	master	19.07.4	lean/lede	older
image/Makefile	phicomm_k3	phicomm-k3	phicomm-k3	phicomm-k3
menuconfig	bcm53xx引入subtarget		引入subtarget
k3screenctrl/Makefile	generic_DEVICE_phicomm_k3	DEVICE_phicomm-k3	generic_DEVICE_phicomm-k3	DEVICE_phicomm-k3

考虑到用lede安装这个分支的k3screenctrl的人也挺多的，还是照顾兼容性吧，所以综合下上面几种情况写成

DEPENDS:=@(TARGET_bcm53xx_generic_DEVICE_phicomm_k3||TARGET_bcm53xx_generic_DEVICE_phicomm-k3||TARGET_bcm53xx_DEVICE_phicomm-k3)