zc_pcie_dma.tcl

#*****************************************************************************************
# Vivado (TM) v2019.2 (64-bit)
#
# zc_pcie_dma.tcl: Tcl script for re-creating project 'zc_pcie_dma'
#
# Generated by Vivado on Wed Nov 25 04:01:05 +07 2020
# IP Build 2700528 on Thu Nov  7 00:09:20 MST 2019
#
# This file contains the Vivado Tcl commands for re-creating the project to the state*
# when this script was generated. In order to re-create the project, please source this
# file in the Vivado Tcl Shell.
#
# * Note that the runs in the created project will be configured the same way as the
#   original project, however they will not be launched automatically. To regenerate the
#   run results please launch the synthesis/implementation runs as needed.
#
#*****************************************************************************************
# NOTE: In order to use this script for source control purposes, please make sure that the
#       following files are added to the source control system:-
#
# 1. This project restoration tcl script (zc_pcie_dma.tcl) that was generated.
#
# 2. The following source(s) files that were local or imported into the original project.
#    (Please see the '$orig_proj_dir' and '$origin_dir' variable setting below at the start of the script)
#
#    "/home/user/Documents/Vivado/zc_pcie_dma/zc_pcie_dma.srcs/sources_1/imports/hdl/pcie_7x_0_pipe_clock.v"
#    "/home/user/Documents/Vivado/zc_pcie_dma/zc_pcie_dma.srcs/sources_1/imports/hdl/pcie_7x_0_support.v"
#    "/home/user/Documents/Vivado/zc_pcie_dma/zc_pcie_dma.srcs/sources_1/imports/hdl/zc_pcie_dma.v"
#    "/home/user/Documents/Vivado/zc_pcie_dma/zc_pcie_dma.srcs/sources_1/ip/pcie_7x_0/pcie_7x_0.xci"
#    "/home/user/Documents/Vivado/zc_pcie_dma/zc_pcie_dma.srcs/constrs_1/imports/hdl/zc706.xdc"
#
# 3. The following remote source files that were added to the original project:-
#
#    <none>
#
#*****************************************************************************************

# Set the reference directory for source file relative paths (by default the value is script directory path)
set origin_dir "."

# Use origin directory path location variable, if specified in the tcl shell
if { [info exists ::origin_dir_loc] } {
  set origin_dir $::origin_dir_loc
}

# Set the project name
set _xil_proj_name_ "zc_pcie_dma"

# Use project name variable, if specified in the tcl shell
if { [info exists ::user_project_name] } {
  set _xil_proj_name_ $::user_project_name
}

variable script_file
set script_file "zc_pcie_dma.tcl"

# Help information for this script
proc print_help {} {
  variable script_file
  puts "\nDescription:"
  puts "Recreate a Vivado project from this script. The created project will be"
  puts "functionally equivalent to the original project for which this script was"
  puts "generated. The script contains commands for creating a project, filesets,"
  puts "runs, adding/importing sources and setting properties on various objects.\n"
  puts "Syntax:"
  puts "$script_file"
  puts "$script_file -tclargs \[--origin_dir <path>\]"
  puts "$script_file -tclargs \[--project_name <name>\]"
  puts "$script_file -tclargs \[--help\]\n"
  puts "Usage:"
  puts "Name                   Description"
  puts "-------------------------------------------------------------------------"
  puts "\[--origin_dir <path>\]  Determine source file paths wrt this path. Default"
  puts "                       origin_dir path value is \".\", otherwise, the value"
  puts "                       that was set with the \"-paths_relative_to\" switch"
  puts "                       when this script was generated.\n"
  puts "\[--project_name <name>\] Create project with the specified name. Default"
  puts "                       name is the name of the project from where this"
  puts "                       script was generated.\n"
  puts "\[--help\]               Print help information for this script"
  puts "-------------------------------------------------------------------------\n"
  exit 0
}

if { $::argc > 0 } {
  for {set i 0} {$i < $::argc} {incr i} {
    set option [string trim [lindex $::argv $i]]
    switch -regexp -- $option {
      "--origin_dir"   { incr i; set origin_dir [lindex $::argv $i] }
      "--project_name" { incr i; set _xil_proj_name_ [lindex $::argv $i] }
      "--help"         { print_help }
      default {
        if { [regexp {^-} $option] } {
          puts "ERROR: Unknown option '$option' specified, please type '$script_file -tclargs --help' for usage info.\n"
          return 1
        }
      }
    }
  }
}

# Set the directory path for the original project from where this script was exported
set orig_proj_dir "[file normalize "$origin_dir/../"]"

# Create project
create_project ${_xil_proj_name_} ./${_xil_proj_name_} -part xc7z045ffg900-2

# Set the directory path for the new project
set proj_dir [get_property directory [current_project]]

# Set project properties
set obj [current_project]
set_property -name "board_part" -value "xilinx.com:zc706:part0:1.4" -objects $obj
set_property -name "default_lib" -value "xil_defaultlib" -objects $obj
set_property -name "enable_vhdl_2008" -value "1" -objects $obj
set_property -name "ip_cache_permissions" -value "read write" -objects $obj
set_property -name "ip_output_repo" -value "$proj_dir/${_xil_proj_name_}.cache/ip" -objects $obj
set_property -name "mem.enable_memory_map_generation" -value "1" -objects $obj
set_property -name "platform.board_id" -value "zc706" -objects $obj
set_property -name "sim.central_dir" -value "$proj_dir/${_xil_proj_name_}.ip_user_files" -objects $obj
set_property -name "sim.ip.auto_export_scripts" -value "1" -objects $obj
set_property -name "simulator_language" -value "Mixed" -objects $obj
set_property -name "webtalk.activehdl_export_sim" -value "11" -objects $obj
set_property -name "webtalk.ies_export_sim" -value "11" -objects $obj
set_property -name "webtalk.modelsim_export_sim" -value "11" -objects $obj
set_property -name "webtalk.questa_export_sim" -value "11" -objects $obj
set_property -name "webtalk.riviera_export_sim" -value "11" -objects $obj
set_property -name "webtalk.vcs_export_sim" -value "11" -objects $obj
set_property -name "webtalk.xcelium_export_sim" -value "2" -objects $obj
set_property -name "webtalk.xsim_export_sim" -value "11" -objects $obj
set_property -name "xpm_libraries" -value "XPM_CDC XPM_FIFO XPM_MEMORY" -objects $obj

# Create 'sources_1' fileset (if not found)
if {[string equal [get_filesets -quiet sources_1] ""]} {
  create_fileset -srcset sources_1
}

# Set 'sources_1' fileset object
set obj [get_filesets sources_1]
# Import local files from the original project
set files [list \
 [file normalize "${origin_dir}/hdl/pcie_7x_0_pipe_clock.v"]\
 [file normalize "${origin_dir}/hdl/pcie_7x_0_support.v"]\
 [file normalize "${origin_dir}/hdl/zc_pcie_dma.v" ]\
]
set imported_files [import_files -fileset sources_1 $files]

# Set 'sources_1' fileset file properties for remote files
# None

# Set 'sources_1' fileset file properties for local files
# None

# Set 'sources_1' fileset properties
set obj [get_filesets sources_1]
set_property -name "top" -value "zc_pcie_dma" -objects $obj

# Set 'sources_1' fileset object
set obj [get_filesets sources_1]
# Import local files from the original project
set files [list \
 [file normalize "${origin_dir}/ip/pcie_7x_0.xci" ]\
]
set imported_files [import_files -fileset sources_1 $files]

# Set 'sources_1' fileset file properties for remote files
# None

# Set 'sources_1' fileset file properties for local files
set file "pcie_7x_0/pcie_7x_0.xci"
set file_obj [get_files -of_objects [get_filesets sources_1] [list "*$file"]]
set_property -name "generate_files_for_reference" -value "0" -objects $file_obj
set_property -name "registered_with_manager" -value "1" -objects $file_obj
if { ![get_property "is_locked" $file_obj] } {
  set_property -name "synth_checkpoint_mode" -value "Singular" -objects $file_obj
}


# Create 'constrs_1' fileset (if not found)
if {[string equal [get_filesets -quiet constrs_1] ""]} {
  create_fileset -constrset constrs_1
}

# Set 'constrs_1' fileset object
set obj [get_filesets constrs_1]

# Add/Import constrs file and set constrs file properties
set file "[file normalize ${origin_dir}/hdl/zc706.xdc]"
set file_imported [import_files -fileset constrs_1 [list $file]]
set file "hdl/zc706.xdc"
set file_obj [get_files -of_objects [get_filesets constrs_1] [list "*$file"]]
set_property -name "file_type" -value "XDC" -objects $file_obj

# Set 'constrs_1' fileset properties
set obj [get_filesets constrs_1]

# Create 'sim_1' fileset (if not found)
if {[string equal [get_filesets -quiet sim_1] ""]} {
  create_fileset -simset sim_1
}

# Set 'sim_1' fileset object
set obj [get_filesets sim_1]
# Empty (no sources present)

# Set 'sim_1' fileset properties
set obj [get_filesets sim_1]
set_property -name "top" -value "zc_pcie_dma" -objects $obj
set_property -name "top_lib" -value "xil_defaultlib" -objects $obj

# Set 'utils_1' fileset object
set obj [get_filesets utils_1]
# Empty (no sources present)

# Set 'utils_1' fileset properties
set obj [get_filesets utils_1]


# Adding sources referenced in BDs, if not already added


# Proc to create BD zynq_soc
proc cr_bd_zynq_soc { parentCell } {

  # CHANGE DESIGN NAME HERE
  set design_name zynq_soc

  common::send_msg_id "BD_TCL-003" "INFO" "Currently there is no design <$design_name> in project, so creating one..."

  create_bd_design $design_name

  set bCheckIPsPassed 1
  ##################################################################
  # CHECK IPs
  ##################################################################
  set bCheckIPs 1
  if { $bCheckIPs == 1 } {
     set list_check_ips "\ 
  xilinx.com:ip:axi_dma:7.1\
  xilinx.com:ip:axi_gpio:2.0\
  xilinx.com:ip:axis_data_fifo:2.0\
  xilinx.com:ip:processing_system7:5.5\
  xilinx.com:ip:proc_sys_reset:5.0\
  xilinx.com:ip:xlconcat:2.1\
  "

   set list_ips_missing ""
   common::send_msg_id "BD_TCL-006" "INFO" "Checking if the following IPs exist in the project's IP catalog: $list_check_ips ."

   foreach ip_vlnv $list_check_ips {
      set ip_obj [get_ipdefs -all $ip_vlnv]
      if { $ip_obj eq "" } {
         lappend list_ips_missing $ip_vlnv
      }
   }

   if { $list_ips_missing ne "" } {
      catch {common::send_msg_id "BD_TCL-115" "ERROR" "The following IPs are not found in the IP Catalog:\n  $list_ips_missing\n\nResolution: Please add the repository containing the IP(s) to the project." }
      set bCheckIPsPassed 0
   }

  }

  if { $bCheckIPsPassed != 1 } {
    common::send_msg_id "BD_TCL-1003" "WARNING" "Will not continue with creation of design due to the error(s) above."
    return 3
  }

  variable script_folder

  if { $parentCell eq "" } {
     set parentCell [get_bd_cells /]
  }

  # Get object for parentCell
  set parentObj [get_bd_cells $parentCell]
  if { $parentObj == "" } {
     catch {common::send_msg_id "BD_TCL-100" "ERROR" "Unable to find parent cell <$parentCell>!"}
     return
  }

  # Make sure parentObj is hier blk
  set parentType [get_property TYPE $parentObj]
  if { $parentType ne "hier" } {
     catch {common::send_msg_id "BD_TCL-101" "ERROR" "Parent <$parentObj> has TYPE = <$parentType>. Expected to be <hier>."}
     return
  }

  # Save current instance; Restore later
  set oldCurInst [current_bd_instance .]

  # Set parent object as current
  current_bd_instance $parentObj


  # Create interface ports
  set DDR [ create_bd_intf_port -mode Master -vlnv xilinx.com:interface:ddrx_rtl:1.0 DDR ]

  set FIXED_IO [ create_bd_intf_port -mode Master -vlnv xilinx.com:display_processing_system7:fixedio_rtl:1.0 FIXED_IO ]

  set GPIO_0 [ create_bd_intf_port -mode Master -vlnv xilinx.com:interface:gpio_rtl:1.0 GPIO_0 ]

  set M_AXIS_MM2S_0 [ create_bd_intf_port -mode Master -vlnv xilinx.com:interface:axis_rtl:1.0 M_AXIS_MM2S_0 ]

  set M_AXIS_MM2S_1 [ create_bd_intf_port -mode Master -vlnv xilinx.com:interface:axis_rtl:1.0 M_AXIS_MM2S_1 ]

  set S_AXIS_S2MM_0 [ create_bd_intf_port -mode Slave -vlnv xilinx.com:interface:axis_rtl:1.0 S_AXIS_S2MM_0 ]
  set_property -dict [ list \
   CONFIG.HAS_TKEEP {0} \
   CONFIG.HAS_TLAST {0} \
   CONFIG.HAS_TREADY {1} \
   CONFIG.HAS_TSTRB {0} \
   CONFIG.LAYERED_METADATA {undef} \
   CONFIG.TDATA_NUM_BYTES {8} \
   CONFIG.TDEST_WIDTH {0} \
   CONFIG.TID_WIDTH {0} \
   CONFIG.TUSER_WIDTH {0} \
   ] $S_AXIS_S2MM_0

  set S_AXIS_S2MM_1 [ create_bd_intf_port -mode Slave -vlnv xilinx.com:interface:axis_rtl:1.0 S_AXIS_S2MM_1 ]
  set_property -dict [ list \
   CONFIG.HAS_TKEEP {1} \
   CONFIG.HAS_TLAST {1} \
   CONFIG.HAS_TREADY {1} \
   CONFIG.HAS_TSTRB {0} \
   CONFIG.LAYERED_METADATA {undef} \
   CONFIG.TDATA_NUM_BYTES {1} \
   CONFIG.TDEST_WIDTH {0} \
   CONFIG.TID_WIDTH {0} \
   CONFIG.TUSER_WIDTH {0} \
   ] $S_AXIS_S2MM_1


  # Create ports
  set m_axis_aclk_0 [ create_bd_port -dir I -type clk m_axis_aclk_0 ]
  set s_axis_aclk_0 [ create_bd_port -dir I -type clk s_axis_aclk_0 ]
  set s_axis_aresetn_0 [ create_bd_port -dir I -type rst s_axis_aresetn_0 ]

  # Create instance: axi_dma_0, and set properties
  set axi_dma_0 [ create_bd_cell -type ip -vlnv xilinx.com:ip:axi_dma:7.1 axi_dma_0 ]
  set_property -dict [ list \
   CONFIG.c_include_sg {0} \
   CONFIG.c_m_axi_mm2s_data_width {64} \
   CONFIG.c_m_axi_s2mm_data_width {64} \
   CONFIG.c_m_axis_mm2s_tdata_width {64} \
   CONFIG.c_mm2s_burst_size {32} \
   CONFIG.c_s2mm_burst_size {32} \
   CONFIG.c_s_axis_s2mm_tdata_width {64} \
   CONFIG.c_sg_include_stscntrl_strm {0} \
 ] $axi_dma_0

  # Create instance: axi_dma_1, and set properties
  set axi_dma_1 [ create_bd_cell -type ip -vlnv xilinx.com:ip:axi_dma:7.1 axi_dma_1 ]
  set_property -dict [ list \
   CONFIG.c_include_sg {0} \
   CONFIG.c_sg_include_stscntrl_strm {0} \
 ] $axi_dma_1

  # Create instance: axi_gpio_0, and set properties
  set axi_gpio_0 [ create_bd_cell -type ip -vlnv xilinx.com:ip:axi_gpio:2.0 axi_gpio_0 ]
  set_property -dict [ list \
   CONFIG.C_ALL_INPUTS {1} \
 ] $axi_gpio_0

  # Create instance: axis_data_fifo_0, and set properties
  set axis_data_fifo_0 [ create_bd_cell -type ip -vlnv xilinx.com:ip:axis_data_fifo:2.0 axis_data_fifo_0 ]
  set_property -dict [ list \
   CONFIG.FIFO_DEPTH {1024} \
   CONFIG.FIFO_MODE {2} \
   CONFIG.HAS_TKEEP {1} \
   CONFIG.HAS_TLAST {1} \
   CONFIG.IS_ACLK_ASYNC {1} \
   CONFIG.TDATA_NUM_BYTES {8} \
 ] $axis_data_fifo_0

  # Create instance: axis_data_fifo_1, and set properties
  set axis_data_fifo_1 [ create_bd_cell -type ip -vlnv xilinx.com:ip:axis_data_fifo:2.0 axis_data_fifo_1 ]
  set_property -dict [ list \
   CONFIG.FIFO_DEPTH {1024} \
   CONFIG.FIFO_MODE {2} \
   CONFIG.HAS_TKEEP {1} \
   CONFIG.HAS_TLAST {1} \
   CONFIG.IS_ACLK_ASYNC {1} \
   CONFIG.TDATA_NUM_BYTES {8} \
 ] $axis_data_fifo_1

  # Create instance: axis_data_fifo_2, and set properties
  set axis_data_fifo_2 [ create_bd_cell -type ip -vlnv xilinx.com:ip:axis_data_fifo:2.0 axis_data_fifo_2 ]
  set_property -dict [ list \
   CONFIG.FIFO_DEPTH {16} \
   CONFIG.FIFO_MODE {2} \
   CONFIG.HAS_TKEEP {1} \
   CONFIG.IS_ACLK_ASYNC {1} \
   CONFIG.TDATA_NUM_BYTES {4} \
 ] $axis_data_fifo_2

  # Create instance: axis_data_fifo_3, and set properties
  set axis_data_fifo_3 [ create_bd_cell -type ip -vlnv xilinx.com:ip:axis_data_fifo:2.0 axis_data_fifo_3 ]
  set_property -dict [ list \
   CONFIG.FIFO_DEPTH {16} \
   CONFIG.FIFO_MODE {2} \
   CONFIG.HAS_TKEEP {1} \
   CONFIG.IS_ACLK_ASYNC {1} \
   CONFIG.TDATA_NUM_BYTES {4} \
 ] $axis_data_fifo_3

  # Create instance: processing_system7_0, and set properties
  set processing_system7_0 [ create_bd_cell -type ip -vlnv xilinx.com:ip:processing_system7:5.5 processing_system7_0 ]
  set_property -dict [ list \
   CONFIG.PCW_ACT_APU_PERIPHERAL_FREQMHZ {666.666687} \
   CONFIG.PCW_ACT_CAN_PERIPHERAL_FREQMHZ {10.000000} \
   CONFIG.PCW_ACT_DCI_PERIPHERAL_FREQMHZ {10.158730} \
   CONFIG.PCW_ACT_ENET0_PERIPHERAL_FREQMHZ {25.000000} \
   CONFIG.PCW_ACT_ENET1_PERIPHERAL_FREQMHZ {10.000000} \
   CONFIG.PCW_ACT_FPGA0_PERIPHERAL_FREQMHZ {50.000000} \
   CONFIG.PCW_ACT_FPGA1_PERIPHERAL_FREQMHZ {10.000000} \
   CONFIG.PCW_ACT_FPGA2_PERIPHERAL_FREQMHZ {10.000000} \
   CONFIG.PCW_ACT_FPGA3_PERIPHERAL_FREQMHZ {10.000000} \
   CONFIG.PCW_ACT_PCAP_PERIPHERAL_FREQMHZ {200.000000} \
   CONFIG.PCW_ACT_QSPI_PERIPHERAL_FREQMHZ {200.000000} \
   CONFIG.PCW_ACT_SDIO_PERIPHERAL_FREQMHZ {50.000000} \
   CONFIG.PCW_ACT_SMC_PERIPHERAL_FREQMHZ {10.000000} \
   CONFIG.PCW_ACT_SPI_PERIPHERAL_FREQMHZ {10.000000} \
   CONFIG.PCW_ACT_TPIU_PERIPHERAL_FREQMHZ {200.000000} \
   CONFIG.PCW_ACT_TTC0_CLK0_PERIPHERAL_FREQMHZ {111.111115} \
   CONFIG.PCW_ACT_TTC0_CLK1_PERIPHERAL_FREQMHZ {111.111115} \
   CONFIG.PCW_ACT_TTC0_CLK2_PERIPHERAL_FREQMHZ {111.111115} \
   CONFIG.PCW_ACT_TTC1_CLK0_PERIPHERAL_FREQMHZ {111.111115} \
   CONFIG.PCW_ACT_TTC1_CLK1_PERIPHERAL_FREQMHZ {111.111115} \
   CONFIG.PCW_ACT_TTC1_CLK2_PERIPHERAL_FREQMHZ {111.111115} \
   CONFIG.PCW_ACT_UART_PERIPHERAL_FREQMHZ {50.000000} \
   CONFIG.PCW_ACT_WDT_PERIPHERAL_FREQMHZ {111.111115} \
   CONFIG.PCW_APU_PERIPHERAL_FREQMHZ {667.000000} \
   CONFIG.PCW_ARMPLL_CTRL_FBDIV {40} \
   CONFIG.PCW_CAN0_GRP_CLK_ENABLE {0} \
   CONFIG.PCW_CAN0_PERIPHERAL_ENABLE {0} \
   CONFIG.PCW_CAN_PERIPHERAL_DIVISOR0 {1} \
   CONFIG.PCW_CAN_PERIPHERAL_DIVISOR1 {1} \
   CONFIG.PCW_CAN_PERIPHERAL_FREQMHZ {100} \
   CONFIG.PCW_CLK0_FREQ {50000000} \
   CONFIG.PCW_CLK1_FREQ {10000000} \
   CONFIG.PCW_CLK2_FREQ {10000000} \
   CONFIG.PCW_CLK3_FREQ {10000000} \
   CONFIG.PCW_CPU_CPU_PLL_FREQMHZ {1333.333} \
   CONFIG.PCW_CPU_PERIPHERAL_DIVISOR0 {2} \
   CONFIG.PCW_DCI_PERIPHERAL_DIVISOR0 {15} \
   CONFIG.PCW_DCI_PERIPHERAL_DIVISOR1 {7} \
   CONFIG.PCW_DDRPLL_CTRL_FBDIV {32} \
   CONFIG.PCW_DDR_DDR_PLL_FREQMHZ {1066.667} \
   CONFIG.PCW_DDR_PERIPHERAL_DIVISOR0 {2} \
   CONFIG.PCW_DDR_RAM_HIGHADDR {0x3FFFFFFF} \
   CONFIG.PCW_DUAL_PARALLEL_QSPI_DATA_MODE {x8} \
   CONFIG.PCW_ENET0_ENET0_IO {MIO 16 .. 27} \
   CONFIG.PCW_ENET0_GRP_MDIO_ENABLE {1} \
   CONFIG.PCW_ENET0_GRP_MDIO_IO {MIO 52 .. 53} \
   CONFIG.PCW_ENET0_PERIPHERAL_DIVISOR0 {8} \
   CONFIG.PCW_ENET0_PERIPHERAL_DIVISOR1 {5} \
   CONFIG.PCW_ENET0_PERIPHERAL_ENABLE {1} \
   CONFIG.PCW_ENET0_PERIPHERAL_FREQMHZ {100 Mbps} \
   CONFIG.PCW_ENET0_RESET_ENABLE {1} \
   CONFIG.PCW_ENET0_RESET_IO {MIO 47} \
   CONFIG.PCW_ENET1_PERIPHERAL_DIVISOR0 {1} \
   CONFIG.PCW_ENET1_PERIPHERAL_DIVISOR1 {1} \
   CONFIG.PCW_ENET1_RESET_ENABLE {0} \
   CONFIG.PCW_ENET_RESET_ENABLE {1} \
   CONFIG.PCW_ENET_RESET_SELECT {Share reset pin} \
   CONFIG.PCW_EN_EMIO_TTC0 {1} \
   CONFIG.PCW_EN_ENET0 {1} \
   CONFIG.PCW_EN_GPIO {1} \
   CONFIG.PCW_EN_I2C0 {1} \
   CONFIG.PCW_EN_QSPI {1} \
   CONFIG.PCW_EN_SDIO0 {1} \
   CONFIG.PCW_EN_TTC0 {1} \
   CONFIG.PCW_EN_UART1 {1} \
   CONFIG.PCW_EN_USB0 {1} \
   CONFIG.PCW_FCLK0_PERIPHERAL_DIVISOR0 {5} \
   CONFIG.PCW_FCLK0_PERIPHERAL_DIVISOR1 {4} \
   CONFIG.PCW_FCLK1_PERIPHERAL_DIVISOR0 {1} \
   CONFIG.PCW_FCLK1_PERIPHERAL_DIVISOR1 {1} \
   CONFIG.PCW_FCLK2_PERIPHERAL_DIVISOR0 {1} \
   CONFIG.PCW_FCLK2_PERIPHERAL_DIVISOR1 {1} \
   CONFIG.PCW_FCLK3_PERIPHERAL_DIVISOR0 {1} \
   CONFIG.PCW_FCLK3_PERIPHERAL_DIVISOR1 {1} \
   CONFIG.PCW_FPGA_FCLK0_ENABLE {1} \
   CONFIG.PCW_FPGA_FCLK1_ENABLE {0} \
   CONFIG.PCW_FPGA_FCLK2_ENABLE {0} \
   CONFIG.PCW_FPGA_FCLK3_ENABLE {0} \
   CONFIG.PCW_GPIO_MIO_GPIO_ENABLE {1} \
   CONFIG.PCW_GPIO_MIO_GPIO_IO {MIO} \
   CONFIG.PCW_I2C0_GRP_INT_ENABLE {0} \
   CONFIG.PCW_I2C0_I2C0_IO {MIO 50 .. 51} \
   CONFIG.PCW_I2C0_PERIPHERAL_ENABLE {1} \
   CONFIG.PCW_I2C0_RESET_ENABLE {1} \
   CONFIG.PCW_I2C0_RESET_IO {MIO 46} \
   CONFIG.PCW_I2C1_RESET_ENABLE {0} \
   CONFIG.PCW_I2C_PERIPHERAL_FREQMHZ {111.111115} \
   CONFIG.PCW_I2C_RESET_ENABLE {1} \
   CONFIG.PCW_I2C_RESET_SELECT {Share reset pin} \
   CONFIG.PCW_IOPLL_CTRL_FBDIV {30} \
   CONFIG.PCW_IO_IO_PLL_FREQMHZ {1000.000} \
   CONFIG.PCW_IRQ_F2P_INTR {1} \
   CONFIG.PCW_MIO_0_DIRECTION {out} \
   CONFIG.PCW_MIO_0_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_0_PULLUP {enabled} \
   CONFIG.PCW_MIO_0_SLEW {slow} \
   CONFIG.PCW_MIO_10_DIRECTION {inout} \
   CONFIG.PCW_MIO_10_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_10_PULLUP {enabled} \
   CONFIG.PCW_MIO_10_SLEW {slow} \
   CONFIG.PCW_MIO_11_DIRECTION {inout} \
   CONFIG.PCW_MIO_11_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_11_PULLUP {enabled} \
   CONFIG.PCW_MIO_11_SLEW {slow} \
   CONFIG.PCW_MIO_12_DIRECTION {inout} \
   CONFIG.PCW_MIO_12_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_12_PULLUP {enabled} \
   CONFIG.PCW_MIO_12_SLEW {slow} \
   CONFIG.PCW_MIO_13_DIRECTION {inout} \
   CONFIG.PCW_MIO_13_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_13_PULLUP {enabled} \
   CONFIG.PCW_MIO_13_SLEW {slow} \
   CONFIG.PCW_MIO_14_DIRECTION {in} \
   CONFIG.PCW_MIO_14_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_14_PULLUP {enabled} \
   CONFIG.PCW_MIO_14_SLEW {slow} \
   CONFIG.PCW_MIO_15_DIRECTION {in} \
   CONFIG.PCW_MIO_15_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_15_PULLUP {enabled} \
   CONFIG.PCW_MIO_15_SLEW {slow} \
   CONFIG.PCW_MIO_16_DIRECTION {out} \
   CONFIG.PCW_MIO_16_IOTYPE {HSTL 1.8V} \
   CONFIG.PCW_MIO_16_PULLUP {disabled} \
   CONFIG.PCW_MIO_16_SLEW {slow} \
   CONFIG.PCW_MIO_17_DIRECTION {out} \
   CONFIG.PCW_MIO_17_IOTYPE {HSTL 1.8V} \
   CONFIG.PCW_MIO_17_PULLUP {disabled} \
   CONFIG.PCW_MIO_17_SLEW {slow} \
   CONFIG.PCW_MIO_18_DIRECTION {out} \
   CONFIG.PCW_MIO_18_IOTYPE {HSTL 1.8V} \
   CONFIG.PCW_MIO_18_PULLUP {disabled} \
   CONFIG.PCW_MIO_18_SLEW {slow} \
   CONFIG.PCW_MIO_19_DIRECTION {out} \
   CONFIG.PCW_MIO_19_IOTYPE {HSTL 1.8V} \
   CONFIG.PCW_MIO_19_PULLUP {disabled} \
   CONFIG.PCW_MIO_19_SLEW {slow} \
   CONFIG.PCW_MIO_1_DIRECTION {out} \
   CONFIG.PCW_MIO_1_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_1_PULLUP {enabled} \
   CONFIG.PCW_MIO_1_SLEW {slow} \
   CONFIG.PCW_MIO_20_DIRECTION {out} \
   CONFIG.PCW_MIO_20_IOTYPE {HSTL 1.8V} \
   CONFIG.PCW_MIO_20_PULLUP {disabled} \
   CONFIG.PCW_MIO_20_SLEW {slow} \
   CONFIG.PCW_MIO_21_DIRECTION {out} \
   CONFIG.PCW_MIO_21_IOTYPE {HSTL 1.8V} \
   CONFIG.PCW_MIO_21_PULLUP {disabled} \
   CONFIG.PCW_MIO_21_SLEW {slow} \
   CONFIG.PCW_MIO_22_DIRECTION {in} \
   CONFIG.PCW_MIO_22_IOTYPE {HSTL 1.8V} \
   CONFIG.PCW_MIO_22_PULLUP {disabled} \
   CONFIG.PCW_MIO_22_SLEW {slow} \
   CONFIG.PCW_MIO_23_DIRECTION {in} \
   CONFIG.PCW_MIO_23_IOTYPE {HSTL 1.8V} \
   CONFIG.PCW_MIO_23_PULLUP {disabled} \
   CONFIG.PCW_MIO_23_SLEW {slow} \
   CONFIG.PCW_MIO_24_DIRECTION {in} \
   CONFIG.PCW_MIO_24_IOTYPE {HSTL 1.8V} \
   CONFIG.PCW_MIO_24_PULLUP {disabled} \
   CONFIG.PCW_MIO_24_SLEW {slow} \
   CONFIG.PCW_MIO_25_DIRECTION {in} \
   CONFIG.PCW_MIO_25_IOTYPE {HSTL 1.8V} \
   CONFIG.PCW_MIO_25_PULLUP {disabled} \
   CONFIG.PCW_MIO_25_SLEW {slow} \
   CONFIG.PCW_MIO_26_DIRECTION {in} \
   CONFIG.PCW_MIO_26_IOTYPE {HSTL 1.8V} \
   CONFIG.PCW_MIO_26_PULLUP {disabled} \
   CONFIG.PCW_MIO_26_SLEW {slow} \
   CONFIG.PCW_MIO_27_DIRECTION {in} \
   CONFIG.PCW_MIO_27_IOTYPE {HSTL 1.8V} \
   CONFIG.PCW_MIO_27_PULLUP {disabled} \
   CONFIG.PCW_MIO_27_SLEW {slow} \
   CONFIG.PCW_MIO_28_DIRECTION {inout} \
   CONFIG.PCW_MIO_28_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_28_PULLUP {disabled} \
   CONFIG.PCW_MIO_28_SLEW {slow} \
   CONFIG.PCW_MIO_29_DIRECTION {in} \
   CONFIG.PCW_MIO_29_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_29_PULLUP {disabled} \
   CONFIG.PCW_MIO_29_SLEW {slow} \
   CONFIG.PCW_MIO_2_DIRECTION {inout} \
   CONFIG.PCW_MIO_2_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_2_PULLUP {disabled} \
   CONFIG.PCW_MIO_2_SLEW {slow} \
   CONFIG.PCW_MIO_30_DIRECTION {out} \
   CONFIG.PCW_MIO_30_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_30_PULLUP {disabled} \
   CONFIG.PCW_MIO_30_SLEW {slow} \
   CONFIG.PCW_MIO_31_DIRECTION {in} \
   CONFIG.PCW_MIO_31_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_31_PULLUP {disabled} \
   CONFIG.PCW_MIO_31_SLEW {slow} \
   CONFIG.PCW_MIO_32_DIRECTION {inout} \
   CONFIG.PCW_MIO_32_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_32_PULLUP {disabled} \
   CONFIG.PCW_MIO_32_SLEW {slow} \
   CONFIG.PCW_MIO_33_DIRECTION {inout} \
   CONFIG.PCW_MIO_33_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_33_PULLUP {disabled} \
   CONFIG.PCW_MIO_33_SLEW {slow} \
   CONFIG.PCW_MIO_34_DIRECTION {inout} \
   CONFIG.PCW_MIO_34_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_34_PULLUP {disabled} \
   CONFIG.PCW_MIO_34_SLEW {slow} \
   CONFIG.PCW_MIO_35_DIRECTION {inout} \
   CONFIG.PCW_MIO_35_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_35_PULLUP {disabled} \
   CONFIG.PCW_MIO_35_SLEW {slow} \
   CONFIG.PCW_MIO_36_DIRECTION {in} \
   CONFIG.PCW_MIO_36_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_36_PULLUP {disabled} \
   CONFIG.PCW_MIO_36_SLEW {slow} \
   CONFIG.PCW_MIO_37_DIRECTION {inout} \
   CONFIG.PCW_MIO_37_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_37_PULLUP {disabled} \
   CONFIG.PCW_MIO_37_SLEW {slow} \
   CONFIG.PCW_MIO_38_DIRECTION {inout} \
   CONFIG.PCW_MIO_38_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_38_PULLUP {disabled} \
   CONFIG.PCW_MIO_38_SLEW {slow} \
   CONFIG.PCW_MIO_39_DIRECTION {inout} \
   CONFIG.PCW_MIO_39_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_39_PULLUP {disabled} \
   CONFIG.PCW_MIO_39_SLEW {slow} \
   CONFIG.PCW_MIO_3_DIRECTION {inout} \
   CONFIG.PCW_MIO_3_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_3_PULLUP {disabled} \
   CONFIG.PCW_MIO_3_SLEW {slow} \
   CONFIG.PCW_MIO_40_DIRECTION {inout} \
   CONFIG.PCW_MIO_40_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_40_PULLUP {disabled} \
   CONFIG.PCW_MIO_40_SLEW {slow} \
   CONFIG.PCW_MIO_41_DIRECTION {inout} \
   CONFIG.PCW_MIO_41_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_41_PULLUP {disabled} \
   CONFIG.PCW_MIO_41_SLEW {slow} \
   CONFIG.PCW_MIO_42_DIRECTION {inout} \
   CONFIG.PCW_MIO_42_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_42_PULLUP {disabled} \
   CONFIG.PCW_MIO_42_SLEW {slow} \
   CONFIG.PCW_MIO_43_DIRECTION {inout} \
   CONFIG.PCW_MIO_43_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_43_PULLUP {disabled} \
   CONFIG.PCW_MIO_43_SLEW {slow} \
   CONFIG.PCW_MIO_44_DIRECTION {inout} \
   CONFIG.PCW_MIO_44_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_44_PULLUP {disabled} \
   CONFIG.PCW_MIO_44_SLEW {slow} \
   CONFIG.PCW_MIO_45_DIRECTION {inout} \
   CONFIG.PCW_MIO_45_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_45_PULLUP {disabled} \
   CONFIG.PCW_MIO_45_SLEW {slow} \
   CONFIG.PCW_MIO_46_DIRECTION {out} \
   CONFIG.PCW_MIO_46_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_46_PULLUP {enabled} \
   CONFIG.PCW_MIO_46_SLEW {slow} \
   CONFIG.PCW_MIO_47_DIRECTION {out} \
   CONFIG.PCW_MIO_47_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_47_PULLUP {enabled} \
   CONFIG.PCW_MIO_47_SLEW {slow} \
   CONFIG.PCW_MIO_48_DIRECTION {out} \
   CONFIG.PCW_MIO_48_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_48_PULLUP {disabled} \
   CONFIG.PCW_MIO_48_SLEW {slow} \
   CONFIG.PCW_MIO_49_DIRECTION {in} \
   CONFIG.PCW_MIO_49_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_49_PULLUP {disabled} \
   CONFIG.PCW_MIO_49_SLEW {slow} \
   CONFIG.PCW_MIO_4_DIRECTION {inout} \
   CONFIG.PCW_MIO_4_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_4_PULLUP {disabled} \
   CONFIG.PCW_MIO_4_SLEW {slow} \
   CONFIG.PCW_MIO_50_DIRECTION {inout} \
   CONFIG.PCW_MIO_50_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_50_PULLUP {enabled} \
   CONFIG.PCW_MIO_50_SLEW {slow} \
   CONFIG.PCW_MIO_51_DIRECTION {inout} \
   CONFIG.PCW_MIO_51_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_51_PULLUP {enabled} \
   CONFIG.PCW_MIO_51_SLEW {slow} \
   CONFIG.PCW_MIO_52_DIRECTION {out} \
   CONFIG.PCW_MIO_52_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_52_PULLUP {disabled} \
   CONFIG.PCW_MIO_52_SLEW {slow} \
   CONFIG.PCW_MIO_53_DIRECTION {inout} \
   CONFIG.PCW_MIO_53_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_53_PULLUP {disabled} \
   CONFIG.PCW_MIO_53_SLEW {slow} \
   CONFIG.PCW_MIO_5_DIRECTION {inout} \
   CONFIG.PCW_MIO_5_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_5_PULLUP {disabled} \
   CONFIG.PCW_MIO_5_SLEW {slow} \
   CONFIG.PCW_MIO_6_DIRECTION {out} \
   CONFIG.PCW_MIO_6_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_6_PULLUP {disabled} \
   CONFIG.PCW_MIO_6_SLEW {slow} \
   CONFIG.PCW_MIO_7_DIRECTION {out} \
   CONFIG.PCW_MIO_7_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_7_PULLUP {disabled} \
   CONFIG.PCW_MIO_7_SLEW {slow} \
   CONFIG.PCW_MIO_8_DIRECTION {out} \
   CONFIG.PCW_MIO_8_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_8_PULLUP {disabled} \
   CONFIG.PCW_MIO_8_SLEW {slow} \
   CONFIG.PCW_MIO_9_DIRECTION {out} \
   CONFIG.PCW_MIO_9_IOTYPE {LVCMOS 1.8V} \
   CONFIG.PCW_MIO_9_PULLUP {enabled} \
   CONFIG.PCW_MIO_9_SLEW {slow} \
   CONFIG.PCW_MIO_TREE_PERIPHERALS {Quad SPI Flash#Quad SPI Flash#Quad SPI Flash#Quad SPI Flash#Quad SPI Flash#Quad SPI Flash#Quad SPI Flash#USB Reset#Quad SPI Flash#Quad SPI Flash#Quad SPI Flash#Quad SPI Flash#Quad SPI Flash#Quad SPI Flash#SD 0#SD 0#Enet 0#Enet 0#Enet 0#Enet 0#Enet 0#Enet 0#Enet 0#Enet 0#Enet 0#Enet 0#Enet 0#Enet 0#USB 0#USB 0#USB 0#USB 0#USB 0#USB 0#USB 0#USB 0#USB 0#USB 0#USB 0#USB 0#SD 0#SD 0#SD 0#SD 0#SD 0#SD 0#I2C Reset#ENET Reset#UART 1#UART 1#I2C 0#I2C 0#Enet 0#Enet 0} \
   CONFIG.PCW_MIO_TREE_SIGNALS {qspi1_ss_b#qspi0_ss_b#qspi0_io[0]#qspi0_io[1]#qspi0_io[2]#qspi0_io[3]/HOLD_B#qspi0_sclk#reset#qspi_fbclk#qspi1_sclk#qspi1_io[0]#qspi1_io[1]#qspi1_io[2]#qspi1_io[3]#cd#wp#tx_clk#txd[0]#txd[1]#txd[2]#txd[3]#tx_ctl#rx_clk#rxd[0]#rxd[1]#rxd[2]#rxd[3]#rx_ctl#data[4]#dir#stp#nxt#data[0]#data[1]#data[2]#data[3]#clk#data[5]#data[6]#data[7]#clk#cmd#data[0]#data[1]#data[2]#data[3]#reset#reset#tx#rx#scl#sda#mdc#mdio} \
   CONFIG.PCW_NAND_GRP_D8_ENABLE {0} \
   CONFIG.PCW_NAND_PERIPHERAL_ENABLE {0} \
   CONFIG.PCW_NOR_GRP_A25_ENABLE {0} \
   CONFIG.PCW_NOR_GRP_CS0_ENABLE {0} \
   CONFIG.PCW_NOR_GRP_CS1_ENABLE {0} \
   CONFIG.PCW_NOR_GRP_SRAM_CS0_ENABLE {0} \
   CONFIG.PCW_NOR_GRP_SRAM_CS1_ENABLE {0} \
   CONFIG.PCW_NOR_GRP_SRAM_INT_ENABLE {0} \
   CONFIG.PCW_NOR_PERIPHERAL_ENABLE {0} \
   CONFIG.PCW_PCAP_PERIPHERAL_DIVISOR0 {5} \
   CONFIG.PCW_PJTAG_PERIPHERAL_ENABLE {0} \
   CONFIG.PCW_PRESET_BANK0_VOLTAGE {LVCMOS 1.8V} \
   CONFIG.PCW_PRESET_BANK1_VOLTAGE {LVCMOS 1.8V} \
   CONFIG.PCW_QSPI_GRP_FBCLK_ENABLE {1} \
   CONFIG.PCW_QSPI_GRP_FBCLK_IO {MIO 8} \
   CONFIG.PCW_QSPI_GRP_IO1_ENABLE {1} \
   CONFIG.PCW_QSPI_GRP_IO1_IO {MIO 0 9 .. 13} \
   CONFIG.PCW_QSPI_GRP_SINGLE_SS_ENABLE {0} \
   CONFIG.PCW_QSPI_GRP_SS1_ENABLE {0} \
   CONFIG.PCW_QSPI_INTERNAL_HIGHADDRESS {0xFDFFFFFF} \
   CONFIG.PCW_QSPI_PERIPHERAL_DIVISOR0 {5} \
   CONFIG.PCW_QSPI_PERIPHERAL_ENABLE {1} \
   CONFIG.PCW_QSPI_PERIPHERAL_FREQMHZ {200} \
   CONFIG.PCW_QSPI_QSPI_IO {MIO 1 .. 6} \
   CONFIG.PCW_SD0_GRP_CD_ENABLE {1} \
   CONFIG.PCW_SD0_GRP_CD_IO {MIO 14} \
   CONFIG.PCW_SD0_GRP_POW_ENABLE {0} \
   CONFIG.PCW_SD0_GRP_WP_ENABLE {1} \
   CONFIG.PCW_SD0_GRP_WP_IO {MIO 15} \
   CONFIG.PCW_SD0_PERIPHERAL_ENABLE {1} \
   CONFIG.PCW_SD0_SD0_IO {MIO 40 .. 45} \
   CONFIG.PCW_SDIO_PERIPHERAL_DIVISOR0 {20} \
   CONFIG.PCW_SDIO_PERIPHERAL_FREQMHZ {50} \
   CONFIG.PCW_SDIO_PERIPHERAL_VALID {1} \
   CONFIG.PCW_SMC_PERIPHERAL_DIVISOR0 {1} \
   CONFIG.PCW_SPI_PERIPHERAL_DIVISOR0 {1} \
   CONFIG.PCW_TPIU_PERIPHERAL_DIVISOR0 {1} \
   CONFIG.PCW_TTC0_CLK0_PERIPHERAL_FREQMHZ {133.333333} \
   CONFIG.PCW_TTC0_CLK1_PERIPHERAL_FREQMHZ {133.333333} \
   CONFIG.PCW_TTC0_CLK2_PERIPHERAL_FREQMHZ {133.333333} \
   CONFIG.PCW_TTC0_PERIPHERAL_ENABLE {1} \
   CONFIG.PCW_TTC0_TTC0_IO {EMIO} \
   CONFIG.PCW_TTC_PERIPHERAL_FREQMHZ {50} \
   CONFIG.PCW_UART1_GRP_FULL_ENABLE {0} \
   CONFIG.PCW_UART1_PERIPHERAL_ENABLE {1} \
   CONFIG.PCW_UART1_UART1_IO {MIO 48 .. 49} \
   CONFIG.PCW_UART_PERIPHERAL_DIVISOR0 {20} \
   CONFIG.PCW_UART_PERIPHERAL_FREQMHZ {50} \
   CONFIG.PCW_UART_PERIPHERAL_VALID {1} \
   CONFIG.PCW_UIPARAM_ACT_DDR_FREQ_MHZ {533.333374} \
   CONFIG.PCW_UIPARAM_DDR_BANK_ADDR_COUNT {3} \
   CONFIG.PCW_UIPARAM_DDR_BL {8} \
   CONFIG.PCW_UIPARAM_DDR_BOARD_DELAY0 {0.521} \
   CONFIG.PCW_UIPARAM_DDR_BOARD_DELAY1 {0.636} \
   CONFIG.PCW_UIPARAM_DDR_BOARD_DELAY2 {0.54} \
   CONFIG.PCW_UIPARAM_DDR_BOARD_DELAY3 {0.621} \
   CONFIG.PCW_UIPARAM_DDR_BUS_WIDTH {32 Bit} \
   CONFIG.PCW_UIPARAM_DDR_CL {7} \
   CONFIG.PCW_UIPARAM_DDR_COL_ADDR_COUNT {10} \
   CONFIG.PCW_UIPARAM_DDR_CWL {6} \
   CONFIG.PCW_UIPARAM_DDR_DEVICE_CAPACITY {2048 MBits} \
   CONFIG.PCW_UIPARAM_DDR_DQS_TO_CLK_DELAY_0 {0.226} \
   CONFIG.PCW_UIPARAM_DDR_DQS_TO_CLK_DELAY_1 {0.278} \
   CONFIG.PCW_UIPARAM_DDR_DQS_TO_CLK_DELAY_2 {0.184} \
   CONFIG.PCW_UIPARAM_DDR_DQS_TO_CLK_DELAY_3 {0.309} \
   CONFIG.PCW_UIPARAM_DDR_DRAM_WIDTH {8 Bits} \
   CONFIG.PCW_UIPARAM_DDR_ECC {Disabled} \
   CONFIG.PCW_UIPARAM_DDR_FREQ_MHZ {533.333313} \
   CONFIG.PCW_UIPARAM_DDR_MEMORY_TYPE {DDR 3} \
   CONFIG.PCW_UIPARAM_DDR_PARTNO {Custom} \
   CONFIG.PCW_UIPARAM_DDR_ROW_ADDR_COUNT {15} \
   CONFIG.PCW_UIPARAM_DDR_SPEED_BIN {DDR3_1066F} \
   CONFIG.PCW_UIPARAM_DDR_TRAIN_DATA_EYE {1} \
   CONFIG.PCW_UIPARAM_DDR_TRAIN_READ_GATE {1} \
   CONFIG.PCW_UIPARAM_DDR_TRAIN_WRITE_LEVEL {1} \
   CONFIG.PCW_UIPARAM_DDR_T_FAW {30.0} \
   CONFIG.PCW_UIPARAM_DDR_T_RAS_MIN {36.0} \
   CONFIG.PCW_UIPARAM_DDR_T_RC {49.5} \
   CONFIG.PCW_UIPARAM_DDR_T_RCD {7} \
   CONFIG.PCW_UIPARAM_DDR_T_RP {7} \
   CONFIG.PCW_UIPARAM_DDR_USE_INTERNAL_VREF {1} \
   CONFIG.PCW_USB0_PERIPHERAL_ENABLE {1} \
   CONFIG.PCW_USB0_PERIPHERAL_FREQMHZ {60} \
   CONFIG.PCW_USB0_RESET_ENABLE {1} \
   CONFIG.PCW_USB0_RESET_IO {MIO 7} \
   CONFIG.PCW_USB0_USB0_IO {MIO 28 .. 39} \
   CONFIG.PCW_USB1_RESET_ENABLE {0} \
   CONFIG.PCW_USB_RESET_ENABLE {1} \
   CONFIG.PCW_USB_RESET_SELECT {Share reset pin} \
   CONFIG.PCW_USE_FABRIC_INTERRUPT {1} \
   CONFIG.PCW_USE_S_AXI_HP0 {1} \
   CONFIG.PCW_WDT_PERIPHERAL_ENABLE {0} \
   CONFIG.PCW_WDT_PERIPHERAL_FREQMHZ {133.333333} \
   CONFIG.preset {ZC706} \
 ] $processing_system7_0

  # Create instance: ps7_0_axi_periph, and set properties
  set ps7_0_axi_periph [ create_bd_cell -type ip -vlnv xilinx.com:ip:axi_interconnect:2.1 ps7_0_axi_periph ]
  set_property -dict [ list \
   CONFIG.NUM_MI {4} \
   CONFIG.NUM_SI {5} \
 ] $ps7_0_axi_periph

  # Create instance: rst_ps7_0_50M, and set properties
  set rst_ps7_0_50M [ create_bd_cell -type ip -vlnv xilinx.com:ip:proc_sys_reset:5.0 rst_ps7_0_50M ]

  # Create instance: xlconcat_0, and set properties
  set xlconcat_0 [ create_bd_cell -type ip -vlnv xilinx.com:ip:xlconcat:2.1 xlconcat_0 ]
  set_property -dict [ list \
   CONFIG.NUM_PORTS {4} \
 ] $xlconcat_0

  # Create interface connections
  connect_bd_intf_net -intf_net S01_AXI_1 [get_bd_intf_pins axi_dma_0/M_AXI_MM2S] [get_bd_intf_pins ps7_0_axi_periph/S01_AXI]
  connect_bd_intf_net -intf_net S02_AXI_1 [get_bd_intf_pins axi_dma_0/M_AXI_S2MM] [get_bd_intf_pins ps7_0_axi_periph/S02_AXI]
  connect_bd_intf_net -intf_net S_AXIS_0_1 [get_bd_intf_ports S_AXIS_S2MM_0] [get_bd_intf_pins axis_data_fifo_0/S_AXIS]
  connect_bd_intf_net -intf_net S_AXIS_0_2 [get_bd_intf_ports S_AXIS_S2MM_1] [get_bd_intf_pins axis_data_fifo_2/S_AXIS]
  connect_bd_intf_net -intf_net axi_dma_0_M_AXIS_MM2S [get_bd_intf_pins axi_dma_0/M_AXIS_MM2S] [get_bd_intf_pins axis_data_fifo_1/S_AXIS]
  connect_bd_intf_net -intf_net axi_dma_1_M_AXIS_MM2S [get_bd_intf_pins axi_dma_1/M_AXIS_MM2S] [get_bd_intf_pins axis_data_fifo_3/S_AXIS]
  connect_bd_intf_net -intf_net axi_dma_1_M_AXI_MM2S [get_bd_intf_pins axi_dma_1/M_AXI_MM2S] [get_bd_intf_pins ps7_0_axi_periph/S03_AXI]
  connect_bd_intf_net -intf_net axi_dma_1_M_AXI_S2MM [get_bd_intf_pins axi_dma_1/M_AXI_S2MM] [get_bd_intf_pins ps7_0_axi_periph/S04_AXI]
  connect_bd_intf_net -intf_net axi_gpio_0_GPIO [get_bd_intf_ports GPIO_0] [get_bd_intf_pins axi_gpio_0/GPIO]
  connect_bd_intf_net -intf_net axis_data_fifo_0_M_AXIS [get_bd_intf_pins axi_dma_0/S_AXIS_S2MM] [get_bd_intf_pins axis_data_fifo_0/M_AXIS]
  connect_bd_intf_net -intf_net axis_data_fifo_1_M_AXIS [get_bd_intf_ports M_AXIS_MM2S_0] [get_bd_intf_pins axis_data_fifo_1/M_AXIS]
  connect_bd_intf_net -intf_net axis_data_fifo_2_M_AXIS [get_bd_intf_pins axi_dma_1/S_AXIS_S2MM] [get_bd_intf_pins axis_data_fifo_2/M_AXIS]
  connect_bd_intf_net -intf_net axis_data_fifo_3_M_AXIS [get_bd_intf_ports M_AXIS_MM2S_1] [get_bd_intf_pins axis_data_fifo_3/M_AXIS]
  connect_bd_intf_net -intf_net processing_system7_0_DDR [get_bd_intf_ports DDR] [get_bd_intf_pins processing_system7_0/DDR]
  connect_bd_intf_net -intf_net processing_system7_0_FIXED_IO [get_bd_intf_ports FIXED_IO] [get_bd_intf_pins processing_system7_0/FIXED_IO]
  connect_bd_intf_net -intf_net processing_system7_0_M_AXI_GP0 [get_bd_intf_pins processing_system7_0/M_AXI_GP0] [get_bd_intf_pins ps7_0_axi_periph/S00_AXI]
  connect_bd_intf_net -intf_net ps7_0_axi_periph_M00_AXI [get_bd_intf_pins axi_dma_0/S_AXI_LITE] [get_bd_intf_pins ps7_0_axi_periph/M00_AXI]
  connect_bd_intf_net -intf_net ps7_0_axi_periph_M01_AXI [get_bd_intf_pins processing_system7_0/S_AXI_HP0] [get_bd_intf_pins ps7_0_axi_periph/M01_AXI]
  connect_bd_intf_net -intf_net ps7_0_axi_periph_M02_AXI [get_bd_intf_pins axi_gpio_0/S_AXI] [get_bd_intf_pins ps7_0_axi_periph/M02_AXI]
  connect_bd_intf_net -intf_net ps7_0_axi_periph_M03_AXI [get_bd_intf_pins axi_dma_1/S_AXI_LITE] [get_bd_intf_pins ps7_0_axi_periph/M03_AXI]

  # Create port connections
  connect_bd_net -net axi_dma_0_mm2s_introut [get_bd_pins axi_dma_0/mm2s_introut] [get_bd_pins xlconcat_0/In0]
  connect_bd_net -net axi_dma_0_s2mm_introut [get_bd_pins axi_dma_0/s2mm_introut] [get_bd_pins xlconcat_0/In1]
  connect_bd_net -net axi_dma_1_mm2s_introut [get_bd_pins axi_dma_1/mm2s_introut] [get_bd_pins xlconcat_0/In3]
  connect_bd_net -net axi_dma_1_s2mm_introut [get_bd_pins axi_dma_1/s2mm_introut] [get_bd_pins xlconcat_0/In2]
  connect_bd_net -net m_axis_aclk_0_1 [get_bd_ports m_axis_aclk_0] [get_bd_pins axis_data_fifo_1/m_axis_aclk] [get_bd_pins axis_data_fifo_3/m_axis_aclk]
  connect_bd_net -net processing_system7_0_FCLK_CLK0 [get_bd_pins axi_dma_0/m_axi_mm2s_aclk] [get_bd_pins axi_dma_0/m_axi_s2mm_aclk] [get_bd_pins axi_dma_0/s_axi_lite_aclk] [get_bd_pins axi_dma_1/m_axi_mm2s_aclk] [get_bd_pins axi_dma_1/m_axi_s2mm_aclk] [get_bd_pins axi_dma_1/s_axi_lite_aclk] [get_bd_pins axi_gpio_0/s_axi_aclk] [get_bd_pins axis_data_fifo_0/m_axis_aclk] [get_bd_pins axis_data_fifo_1/s_axis_aclk] [get_bd_pins axis_data_fifo_2/m_axis_aclk] [get_bd_pins axis_data_fifo_3/s_axis_aclk] [get_bd_pins processing_system7_0/FCLK_CLK0] [get_bd_pins processing_system7_0/M_AXI_GP0_ACLK] [get_bd_pins processing_system7_0/S_AXI_HP0_ACLK] [get_bd_pins ps7_0_axi_periph/ACLK] [get_bd_pins ps7_0_axi_periph/M00_ACLK] [get_bd_pins ps7_0_axi_periph/M01_ACLK] [get_bd_pins ps7_0_axi_periph/M02_ACLK] [get_bd_pins ps7_0_axi_periph/M03_ACLK] [get_bd_pins ps7_0_axi_periph/S00_ACLK] [get_bd_pins ps7_0_axi_periph/S01_ACLK] [get_bd_pins ps7_0_axi_periph/S02_ACLK] [get_bd_pins ps7_0_axi_periph/S03_ACLK] [get_bd_pins ps7_0_axi_periph/S04_ACLK] [get_bd_pins rst_ps7_0_50M/slowest_sync_clk]
  connect_bd_net -net processing_system7_0_FCLK_RESET0_N [get_bd_pins processing_system7_0/FCLK_RESET0_N] [get_bd_pins rst_ps7_0_50M/ext_reset_in]
  connect_bd_net -net rst_ps7_0_50M_interconnect_aresetn [get_bd_pins axis_data_fifo_1/s_axis_aresetn] [get_bd_pins axis_data_fifo_3/s_axis_aresetn] [get_bd_pins rst_ps7_0_50M/interconnect_aresetn]
  connect_bd_net -net rst_ps7_0_50M_peripheral_aresetn [get_bd_pins axi_dma_0/axi_resetn] [get_bd_pins axi_dma_1/axi_resetn] [get_bd_pins axi_gpio_0/s_axi_aresetn] [get_bd_pins ps7_0_axi_periph/ARESETN] [get_bd_pins ps7_0_axi_periph/M00_ARESETN] [get_bd_pins ps7_0_axi_periph/M01_ARESETN] [get_bd_pins ps7_0_axi_periph/M02_ARESETN] [get_bd_pins ps7_0_axi_periph/M03_ARESETN] [get_bd_pins ps7_0_axi_periph/S00_ARESETN] [get_bd_pins ps7_0_axi_periph/S01_ARESETN] [get_bd_pins ps7_0_axi_periph/S02_ARESETN] [get_bd_pins ps7_0_axi_periph/S03_ARESETN] [get_bd_pins ps7_0_axi_periph/S04_ARESETN] [get_bd_pins rst_ps7_0_50M/peripheral_aresetn]
  connect_bd_net -net s_axis_aclk_0_1 [get_bd_ports s_axis_aclk_0] [get_bd_pins axis_data_fifo_0/s_axis_aclk] [get_bd_pins axis_data_fifo_2/s_axis_aclk]
  connect_bd_net -net s_axis_aresetn_0_1 [get_bd_ports s_axis_aresetn_0] [get_bd_pins axis_data_fifo_0/s_axis_aresetn] [get_bd_pins axis_data_fifo_2/s_axis_aresetn]
  connect_bd_net -net xlconcat_0_dout [get_bd_pins processing_system7_0/IRQ_F2P] [get_bd_pins xlconcat_0/dout]

  # Create address segments
  assign_bd_address -offset 0x00000000 -range 0x40000000 -target_address_space [get_bd_addr_spaces axi_dma_0/Data_MM2S] [get_bd_addr_segs processing_system7_0/S_AXI_HP0/HP0_DDR_LOWOCM] -force
  assign_bd_address -offset 0x00000000 -range 0x40000000 -target_address_space [get_bd_addr_spaces axi_dma_0/Data_S2MM] [get_bd_addr_segs processing_system7_0/S_AXI_HP0/HP0_DDR_LOWOCM] -force
  assign_bd_address -offset 0x00000000 -range 0x40000000 -target_address_space [get_bd_addr_spaces axi_dma_1/Data_MM2S] [get_bd_addr_segs processing_system7_0/S_AXI_HP0/HP0_DDR_LOWOCM] -force
  assign_bd_address -offset 0x00000000 -range 0x40000000 -target_address_space [get_bd_addr_spaces axi_dma_1/Data_S2MM] [get_bd_addr_segs processing_system7_0/S_AXI_HP0/HP0_DDR_LOWOCM] -force
  assign_bd_address -offset 0x40400000 -range 0x00010000 -target_address_space [get_bd_addr_spaces processing_system7_0/Data] [get_bd_addr_segs axi_dma_0/S_AXI_LITE/Reg] -force
  assign_bd_address -offset 0x40410000 -range 0x00010000 -target_address_space [get_bd_addr_spaces processing_system7_0/Data] [get_bd_addr_segs axi_dma_1/S_AXI_LITE/Reg] -force
  assign_bd_address -offset 0x41200000 -range 0x00010000 -target_address_space [get_bd_addr_spaces processing_system7_0/Data] [get_bd_addr_segs axi_gpio_0/S_AXI/Reg] -force

  # Exclude Address Segments
  exclude_bd_addr_seg -offset 0x40400000 -range 0x00010000 -target_address_space [get_bd_addr_spaces axi_dma_0/Data_MM2S] [get_bd_addr_segs axi_dma_0/S_AXI_LITE/Reg]
  exclude_bd_addr_seg -offset 0x40410000 -range 0x00010000 -target_address_space [get_bd_addr_spaces axi_dma_0/Data_MM2S] [get_bd_addr_segs axi_dma_1/S_AXI_LITE/Reg]
  exclude_bd_addr_seg -offset 0x41200000 -range 0x00010000 -target_address_space [get_bd_addr_spaces axi_dma_0/Data_MM2S] [get_bd_addr_segs axi_gpio_0/S_AXI/Reg]
  exclude_bd_addr_seg -offset 0x40400000 -range 0x00010000 -target_address_space [get_bd_addr_spaces axi_dma_0/Data_S2MM] [get_bd_addr_segs axi_dma_0/S_AXI_LITE/Reg]
  exclude_bd_addr_seg -offset 0x40410000 -range 0x00010000 -target_address_space [get_bd_addr_spaces axi_dma_0/Data_S2MM] [get_bd_addr_segs axi_dma_1/S_AXI_LITE/Reg]
  exclude_bd_addr_seg -offset 0x41200000 -range 0x00010000 -target_address_space [get_bd_addr_spaces axi_dma_0/Data_S2MM] [get_bd_addr_segs axi_gpio_0/S_AXI/Reg]
  exclude_bd_addr_seg -offset 0x40400000 -range 0x00010000 -target_address_space [get_bd_addr_spaces axi_dma_1/Data_MM2S] [get_bd_addr_segs axi_dma_0/S_AXI_LITE/Reg]
  exclude_bd_addr_seg -offset 0x40410000 -range 0x00010000 -target_address_space [get_bd_addr_spaces axi_dma_1/Data_MM2S] [get_bd_addr_segs axi_dma_1/S_AXI_LITE/Reg]
  exclude_bd_addr_seg -offset 0x41200000 -range 0x00010000 -target_address_space [get_bd_addr_spaces axi_dma_1/Data_MM2S] [get_bd_addr_segs axi_gpio_0/S_AXI/Reg]
  exclude_bd_addr_seg -offset 0x40400000 -range 0x00010000 -target_address_space [get_bd_addr_spaces axi_dma_1/Data_S2MM] [get_bd_addr_segs axi_dma_0/S_AXI_LITE/Reg]
  exclude_bd_addr_seg -offset 0x40410000 -range 0x00010000 -target_address_space [get_bd_addr_spaces axi_dma_1/Data_S2MM] [get_bd_addr_segs axi_dma_1/S_AXI_LITE/Reg]
  exclude_bd_addr_seg -offset 0x41200000 -range 0x00010000 -target_address_space [get_bd_addr_spaces axi_dma_1/Data_S2MM] [get_bd_addr_segs axi_gpio_0/S_AXI/Reg]
  exclude_bd_addr_seg -target_address_space [get_bd_addr_spaces processing_system7_0/Data] [get_bd_addr_segs processing_system7_0/S_AXI_HP0/HP0_DDR_LOWOCM]

  # Perform GUI Layout
  regenerate_bd_layout -layout_string {
   "ActiveEmotionalView":"Default View",
   "Default View_ScaleFactor":"1.36074",
   "Default View_TopLeft":"-180,492",
   "ExpandedHierarchyInLayout":"",
   "guistr":"# # String gsaved with Nlview 7.0.21  2019-05-29 bk=1.5064 VDI=41 GEI=36 GUI=JA:9.0 TLS
#  -string -flagsOSRD
preplace port DDR -pg 1 -lvl 5 -x 1740 -y 240 -defaultsOSRD
preplace port FIXED_IO -pg 1 -lvl 5 -x 1740 -y 260 -defaultsOSRD
preplace port S_AXIS_S2MM_0 -pg 1 -lvl 0 -x -10 -y 560 -defaultsOSRD
preplace port M_AXIS_MM2S_0 -pg 1 -lvl 5 -x 1740 -y 860 -defaultsOSRD
preplace port GPIO_0 -pg 1 -lvl 5 -x 1740 -y 550 -defaultsOSRD
preplace port S_AXIS_S2MM_1 -pg 1 -lvl 0 -x -10 -y 720 -defaultsOSRD
preplace port M_AXIS_MM2S_1 -pg 1 -lvl 5 -x 1740 -y 1020 -defaultsOSRD
preplace port s_axis_aclk_0 -pg 1 -lvl 0 -x -10 -y 740 -defaultsOSRD
preplace port m_axis_aclk_0 -pg 1 -lvl 0 -x -10 -y 1010 -defaultsOSRD
preplace port s_axis_aresetn_0 -pg 1 -lvl 0 -x -10 -y 580 -defaultsOSRD
preplace inst processing_system7_0 -pg 1 -lvl 4 -x 1470 -y 320 -defaultsOSRD
preplace inst axi_dma_0 -pg 1 -lvl 2 -x 620 -y 520 -defaultsOSRD
preplace inst ps7_0_axi_periph -pg 1 -lvl 3 -x 1050 -y 310 -defaultsOSRD
preplace inst rst_ps7_0_50M -pg 1 -lvl 1 -x 220 -y 400 -defaultsOSRD
preplace inst xlconcat_0 -pg 1 -lvl 3 -x 1050 -y 740 -defaultsOSRD
preplace inst axis_data_fifo_0 -pg 1 -lvl 1 -x 220 -y 590 -defaultsOSRD
preplace inst axis_data_fifo_1 -pg 1 -lvl 4 -x 1470 -y 860 -defaultsOSRD
preplace inst axi_gpio_0 -pg 1 -lvl 4 -x 1470 -y 550 -defaultsOSRD
preplace inst axi_dma_1 -pg 1 -lvl 2 -x 620 -y 780 -defaultsOSRD
preplace inst axis_data_fifo_2 -pg 1 -lvl 1 -x 220 -y 750 -defaultsOSRD
preplace inst axis_data_fifo_3 -pg 1 -lvl 4 -x 1470 -y 1020 -defaultsOSRD
preplace netloc processing_system7_0_FCLK_CLK0 1 0 5 30 300 400 300 860 620 1220 460 1680
preplace netloc processing_system7_0_FCLK_RESET0_N 1 0 5 40 840 420J 640 NJ 640 NJ 640 1690
preplace netloc rst_ps7_0_50M_peripheral_aresetn 1 1 3 410 390 870 610 1210J
preplace netloc axi_dma_0_mm2s_introut 1 2 1 850 560n
preplace netloc axi_dma_0_s2mm_introut 1 2 1 810 580n
preplace netloc xlconcat_0_dout 1 3 1 1200 360n
preplace netloc s_axis_aclk_0_1 1 0 1 10 600n
preplace netloc m_axis_aclk_0_1 1 0 4 NJ 1010 NJ 1010 NJ 1010 1190
preplace netloc s_axis_aresetn_0_1 1 0 1 20 580n
preplace netloc rst_ps7_0_50M_interconnect_aresetn 1 1 3 390 400 830J 840 1200
preplace netloc axi_dma_1_s2mm_introut 1 2 1 790 750n
preplace netloc axi_dma_1_mm2s_introut 1 2 1 870 770n
preplace netloc axis_data_fifo_0_M_AXIS 1 1 1 430 490n
preplace netloc axi_dma_0_M_AXIS_MM2S 1 2 2 820 830 NJ
preplace netloc S_AXIS_0_1 1 0 1 NJ 560
preplace netloc axis_data_fifo_1_M_AXIS 1 4 1 NJ 860
preplace netloc S02_AXI_1 1 2 1 790 110n
preplace netloc processing_system7_0_DDR 1 4 1 NJ 240
preplace netloc ps7_0_axi_periph_M00_AXI 1 1 3 430 10 NJ 10 1220
preplace netloc S01_AXI_1 1 2 1 780 90n
preplace netloc ps7_0_axi_periph_M01_AXI 1 3 1 N 300
preplace netloc axi_dma_1_M_AXI_S2MM 1 2 1 840 150n
preplace netloc processing_system7_0_FIXED_IO 1 4 1 NJ 260
preplace netloc processing_system7_0_M_AXI_GP0 1 2 3 880 630 NJ 630 1700
preplace netloc axi_gpio_0_GPIO 1 4 1 NJ 550
preplace netloc axi_dma_1_M_AXI_MM2S 1 2 1 800 130n
preplace netloc ps7_0_axi_periph_M02_AXI 1 3 1 1210 320n
preplace netloc axis_data_fifo_3_M_AXIS 1 4 1 NJ 1020
preplace netloc axis_data_fifo_2_M_AXIS 1 1 1 N 750
preplace netloc ps7_0_axi_periph_M03_AXI 1 1 3 430 650 NJ 650 1190
preplace netloc S_AXIS_0_2 1 0 1 NJ 720
preplace netloc axi_dma_1_M_AXIS_MM2S 1 2 2 780 990 NJ
levelinfo -pg 1 -10 220 620 1050 1470 1740
pagesize -pg 1 -db -bbox -sgen -180 0 1890 1110
"
}

  # Restore current instance
  current_bd_instance $oldCurInst

  validate_bd_design
  save_bd_design
  close_bd_design $design_name 
}
# End of cr_bd_zynq_soc()
cr_bd_zynq_soc ""
set_property REGISTERED_WITH_MANAGER "1" [get_files zynq_soc.bd ] 
set_property SYNTH_CHECKPOINT_MODE "Hierarchical" [get_files zynq_soc.bd ] 

# Create 'synth_1' run (if not found)
if {[string equal [get_runs -quiet synth_1] ""]} {
    create_run -name synth_1 -part xc7z045ffg900-2 -flow {Vivado Synthesis 2019} -strategy "Vivado Synthesis Defaults" -report_strategy {No Reports} -constrset constrs_1
} else {
  set_property strategy "Vivado Synthesis Defaults" [get_runs synth_1]
  set_property flow "Vivado Synthesis 2019" [get_runs synth_1]
}
set obj [get_runs synth_1]
set_property set_report_strategy_name 1 $obj
set_property report_strategy {Vivado Synthesis Default Reports} $obj
set_property set_report_strategy_name 0 $obj
# Create 'synth_1_synth_report_utilization_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs synth_1] synth_1_synth_report_utilization_0] "" ] } {
  create_report_config -report_name synth_1_synth_report_utilization_0 -report_type report_utilization:1.0 -steps synth_design -runs synth_1
}
set obj [get_report_configs -of_objects [get_runs synth_1] synth_1_synth_report_utilization_0]
if { $obj != "" } {

}
set obj [get_runs synth_1]
set_property -name "strategy" -value "Vivado Synthesis Defaults" -objects $obj

# set the current synth run
current_run -synthesis [get_runs synth_1]

# Create 'impl_1' run (if not found)
if {[string equal [get_runs -quiet impl_1] ""]} {
    create_run -name impl_1 -part xc7z045ffg900-2 -flow {Vivado Implementation 2019} -strategy "Vivado Implementation Defaults" -report_strategy {No Reports} -constrset constrs_1 -parent_run synth_1
} else {
  set_property strategy "Vivado Implementation Defaults" [get_runs impl_1]
  set_property flow "Vivado Implementation 2019" [get_runs impl_1]
}
set obj [get_runs impl_1]
set_property set_report_strategy_name 1 $obj
set_property report_strategy {Vivado Implementation Default Reports} $obj
set_property set_report_strategy_name 0 $obj
# Create 'impl_1_init_report_timing_summary_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_init_report_timing_summary_0] "" ] } {
  create_report_config -report_name impl_1_init_report_timing_summary_0 -report_type report_timing_summary:1.0 -steps init_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_init_report_timing_summary_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "0" -objects $obj
set_property -name "options.max_paths" -value "10" -objects $obj

}
# Create 'impl_1_opt_report_drc_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_opt_report_drc_0] "" ] } {
  create_report_config -report_name impl_1_opt_report_drc_0 -report_type report_drc:1.0 -steps opt_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_opt_report_drc_0]
if { $obj != "" } {

}
# Create 'impl_1_opt_report_timing_summary_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_opt_report_timing_summary_0] "" ] } {
  create_report_config -report_name impl_1_opt_report_timing_summary_0 -report_type report_timing_summary:1.0 -steps opt_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_opt_report_timing_summary_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "0" -objects $obj
set_property -name "options.max_paths" -value "10" -objects $obj

}
# Create 'impl_1_power_opt_report_timing_summary_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_power_opt_report_timing_summary_0] "" ] } {
  create_report_config -report_name impl_1_power_opt_report_timing_summary_0 -report_type report_timing_summary:1.0 -steps power_opt_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_power_opt_report_timing_summary_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "0" -objects $obj
set_property -name "options.max_paths" -value "10" -objects $obj

}
# Create 'impl_1_place_report_io_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_place_report_io_0] "" ] } {
  create_report_config -report_name impl_1_place_report_io_0 -report_type report_io:1.0 -steps place_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_place_report_io_0]
if { $obj != "" } {

}
# Create 'impl_1_place_report_utilization_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_place_report_utilization_0] "" ] } {
  create_report_config -report_name impl_1_place_report_utilization_0 -report_type report_utilization:1.0 -steps place_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_place_report_utilization_0]
if { $obj != "" } {

}
# Create 'impl_1_place_report_control_sets_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_place_report_control_sets_0] "" ] } {
  create_report_config -report_name impl_1_place_report_control_sets_0 -report_type report_control_sets:1.0 -steps place_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_place_report_control_sets_0]
if { $obj != "" } {
set_property -name "options.verbose" -value "1" -objects $obj

}
# Create 'impl_1_place_report_incremental_reuse_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_place_report_incremental_reuse_0] "" ] } {
  create_report_config -report_name impl_1_place_report_incremental_reuse_0 -report_type report_incremental_reuse:1.0 -steps place_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_place_report_incremental_reuse_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "0" -objects $obj

}
# Create 'impl_1_place_report_incremental_reuse_1' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_place_report_incremental_reuse_1] "" ] } {
  create_report_config -report_name impl_1_place_report_incremental_reuse_1 -report_type report_incremental_reuse:1.0 -steps place_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_place_report_incremental_reuse_1]
if { $obj != "" } {
set_property -name "is_enabled" -value "0" -objects $obj

}
# Create 'impl_1_place_report_timing_summary_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_place_report_timing_summary_0] "" ] } {
  create_report_config -report_name impl_1_place_report_timing_summary_0 -report_type report_timing_summary:1.0 -steps place_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_place_report_timing_summary_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "0" -objects $obj
set_property -name "options.max_paths" -value "10" -objects $obj

}
# Create 'impl_1_post_place_power_opt_report_timing_summary_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_post_place_power_opt_report_timing_summary_0] "" ] } {
  create_report_config -report_name impl_1_post_place_power_opt_report_timing_summary_0 -report_type report_timing_summary:1.0 -steps post_place_power_opt_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_post_place_power_opt_report_timing_summary_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "0" -objects $obj
set_property -name "options.max_paths" -value "10" -objects $obj

}
# Create 'impl_1_phys_opt_report_timing_summary_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_phys_opt_report_timing_summary_0] "" ] } {
  create_report_config -report_name impl_1_phys_opt_report_timing_summary_0 -report_type report_timing_summary:1.0 -steps phys_opt_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_phys_opt_report_timing_summary_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "0" -objects $obj
set_property -name "options.max_paths" -value "10" -objects $obj

}
# Create 'impl_1_route_report_drc_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_drc_0] "" ] } {
  create_report_config -report_name impl_1_route_report_drc_0 -report_type report_drc:1.0 -steps route_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_drc_0]
if { $obj != "" } {

}
# Create 'impl_1_route_report_methodology_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_methodology_0] "" ] } {
  create_report_config -report_name impl_1_route_report_methodology_0 -report_type report_methodology:1.0 -steps route_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_methodology_0]
if { $obj != "" } {

}
# Create 'impl_1_route_report_power_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_power_0] "" ] } {
  create_report_config -report_name impl_1_route_report_power_0 -report_type report_power:1.0 -steps route_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_power_0]
if { $obj != "" } {

}
# Create 'impl_1_route_report_route_status_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_route_status_0] "" ] } {
  create_report_config -report_name impl_1_route_report_route_status_0 -report_type report_route_status:1.0 -steps route_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_route_status_0]
if { $obj != "" } {

}
# Create 'impl_1_route_report_timing_summary_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_timing_summary_0] "" ] } {
  create_report_config -report_name impl_1_route_report_timing_summary_0 -report_type report_timing_summary:1.0 -steps route_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_timing_summary_0]
if { $obj != "" } {
set_property -name "options.max_paths" -value "10" -objects $obj

}
# Create 'impl_1_route_report_incremental_reuse_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_incremental_reuse_0] "" ] } {
  create_report_config -report_name impl_1_route_report_incremental_reuse_0 -report_type report_incremental_reuse:1.0 -steps route_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_incremental_reuse_0]
if { $obj != "" } {

}
# Create 'impl_1_route_report_clock_utilization_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_clock_utilization_0] "" ] } {
  create_report_config -report_name impl_1_route_report_clock_utilization_0 -report_type report_clock_utilization:1.0 -steps route_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_clock_utilization_0]
if { $obj != "" } {

}
# Create 'impl_1_route_report_bus_skew_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_bus_skew_0] "" ] } {
  create_report_config -report_name impl_1_route_report_bus_skew_0 -report_type report_bus_skew:1.1 -steps route_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_bus_skew_0]
if { $obj != "" } {
set_property -name "options.warn_on_violation" -value "1" -objects $obj

}
# Create 'impl_1_post_route_phys_opt_report_timing_summary_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_post_route_phys_opt_report_timing_summary_0] "" ] } {
  create_report_config -report_name impl_1_post_route_phys_opt_report_timing_summary_0 -report_type report_timing_summary:1.0 -steps post_route_phys_opt_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_post_route_phys_opt_report_timing_summary_0]
if { $obj != "" } {
set_property -name "options.max_paths" -value "10" -objects $obj
set_property -name "options.warn_on_violation" -value "1" -objects $obj

}
# Create 'impl_1_post_route_phys_opt_report_bus_skew_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_post_route_phys_opt_report_bus_skew_0] "" ] } {
  create_report_config -report_name impl_1_post_route_phys_opt_report_bus_skew_0 -report_type report_bus_skew:1.1 -steps post_route_phys_opt_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_post_route_phys_opt_report_bus_skew_0]
if { $obj != "" } {
set_property -name "options.warn_on_violation" -value "1" -objects $obj

}
set obj [get_runs impl_1]
set_property -name "strategy" -value "Vivado Implementation Defaults" -objects $obj
set_property -name "steps.phys_opt_design.is_enabled" -value "1" -objects $obj
set_property -name "steps.write_bitstream.args.readback_file" -value "0" -objects $obj
set_property -name "steps.write_bitstream.args.verbose" -value "0" -objects $obj

# set the current impl run
current_run -implementation [get_runs impl_1]

puts "INFO: Project created:${_xil_proj_name_}"
# Create 'drc_1' gadget (if not found)
if {[string equal [get_dashboard_gadgets  [ list "drc_1" ] ] ""]} {
create_dashboard_gadget -name {drc_1} -type drc
}
set obj [get_dashboard_gadgets [ list "drc_1" ] ]
set_property -name "reports" -value "impl_1#impl_1_route_report_drc_0" -objects $obj

# Create 'methodology_1' gadget (if not found)
if {[string equal [get_dashboard_gadgets  [ list "methodology_1" ] ] ""]} {
create_dashboard_gadget -name {methodology_1} -type methodology
}
set obj [get_dashboard_gadgets [ list "methodology_1" ] ]
set_property -name "reports" -value "impl_1#impl_1_route_report_methodology_0" -objects $obj

# Create 'power_1' gadget (if not found)
if {[string equal [get_dashboard_gadgets  [ list "power_1" ] ] ""]} {
create_dashboard_gadget -name {power_1} -type power
}
set obj [get_dashboard_gadgets [ list "power_1" ] ]
set_property -name "reports" -value "impl_1#impl_1_route_report_power_0" -objects $obj

# Create 'timing_1' gadget (if not found)
if {[string equal [get_dashboard_gadgets  [ list "timing_1" ] ] ""]} {
create_dashboard_gadget -name {timing_1} -type timing
}
set obj [get_dashboard_gadgets [ list "timing_1" ] ]
set_property -name "reports" -value "impl_1#impl_1_route_report_timing_summary_0" -objects $obj

# Create 'utilization_1' gadget (if not found)
if {[string equal [get_dashboard_gadgets  [ list "utilization_1" ] ] ""]} {
create_dashboard_gadget -name {utilization_1} -type utilization
}
set obj [get_dashboard_gadgets [ list "utilization_1" ] ]
set_property -name "reports" -value "synth_1#synth_1_synth_report_utilization_0" -objects $obj
set_property -name "run.step" -value "synth_design" -objects $obj
set_property -name "run.type" -value "synthesis" -objects $obj

# Create 'utilization_2' gadget (if not found)
if {[string equal [get_dashboard_gadgets  [ list "utilization_2" ] ] ""]} {
create_dashboard_gadget -name {utilization_2} -type utilization
}
set obj [get_dashboard_gadgets [ list "utilization_2" ] ]
set_property -name "reports" -value "impl_1#impl_1_place_report_utilization_0" -objects $obj

move_dashboard_gadget -name {utilization_1} -row 0 -col 0
move_dashboard_gadget -name {power_1} -row 1 -col 0
move_dashboard_gadget -name {drc_1} -row 2 -col 0
move_dashboard_gadget -name {timing_1} -row 0 -col 1
move_dashboard_gadget -name {utilization_2} -row 1 -col 1
move_dashboard_gadget -name {methodology_1} -row 2 -col 1